+ Reply to Thread
Page 1 of 3 1 2 3 LastLast
Results 1 to 10 of 25

Thread: Questions about “Grease, Rifle” history

Click here to increase the font size Click here to reduce the font size
  1. #1
    Legacy Member CalTex's Avatar
    Join Date
    Mar 2009
    Last On
    07-07-2022 @ 06:39 AM
    Posts
    9
    Local Date
    03-28-2024
    Local Time
    09:08 AM

    Questions about “Grease, Rifle” history

    This is not a “what grease should I use” thread, at least I hope not. After I answered a friend’s question about Garandicon lubrication, I realized that I know less about the grease history of this rifle than I would like. Looking around online and in books, I can’t find all that much documented either. Here is what I think I have learned from these sources and where I still have questions:

    - The original grease was “Stano-Rust No. 3” to spec SXS77, adopted in FY38. It is mentioned in the 7/40 edition of FM 23-5 as issued in a tube. Pictures of tubes can be found online. These show instructions on the tube to lube all the usual places, including the compensating spring. So definitely this grease goes back pretty far.

    - Following washout problems and maybe insufficient use of the Stano-Rust, Lubriplate 130-A was adopted in late ’42, following tests vs. several competitors, and provided in the little yellow-lidded containers added to the cleaning kits.

    - At some point apparently after WWII, the little containers marked Lubriplate 130-A were replaced by similar ones just marked “Grease, Rifle”, containing a darker grease that is widely called Plastilube, but sometimes also called Lubriplate. Does anyone know when exactly this change was made, and why?

    - One pound cans of this darker grease used to be widely available. For some reason, every one I have seen is dated 11/63. Coincidence, or what? The cans are marked as “Grease, Rifle”, made by International Lube. Corp, to spec MIL-G-46003, Amend 2.

    - You can still buy commercial Lubriplate 130-A today, and spec sheets are available online.

    - You can still buy a grease marketed as Plastilube today, and find a spec sheet for it. But the current Plastilube is a premium synthetic grease made by Henkel and targeted at brake pad applications, that I doubt has much if any similarity to “Grease, Rifle”.

    - Did Lubriplate 130-A meet the same spec (maybe an earlier revision) as the darker grease?

    - Can anyone comment on what exactly is in the darker grease?

    - The spec for the darker grease was rescinded in 1/09. But there are still some M14s in service. What grease do they use?

    I am hoping the experts here can help fill in or improve any of the above. Sorry for all the questions and thanks so much for any assistance.
    Information
    Warning: This is a relatively older thread
    This discussion is older than 360 days. Some information contained in it may no longer be current.
    Last edited by CalTex; 09-23-2020 at 01:27 PM.

  2. Thank You to CalTex For This Useful Post:


  3. # ADS
    Friends and Sponsors
    Join Date
    October 2006
    Posts
    All Threads
    A Collector's View - The SMLE Short Magazine Lee Enfield 1903-1989. It is 300 8.5x11 inch pages with 1,000+ photo’s, most in color, and each book is serial-numbered.  Covering the SMLE from 1903 to the end of production in India in 1989 it looks at how each model differs and manufacturer differences from a collecting point of view along with the major accessories that could be attached to the rifle. For the record this is not a moneymaker, I hope just to break even, eventually, at $80/book plus shipping.  In the USA shipping is $5.00 for media mail.  I will accept PayPal, Zelle, MO and good old checks (and cash if you want to stop by for a tour!).  CLICK BANNER to send me a PM for International pricing and shipping. Manufacturer of various vintage rifle scopes for the 1903 such as our M73G4 (reproduction of the Weaver 330C) and Malcolm 8X Gen II (Unertl reproduction). Several of our scopes are used in the CMP Vintage Sniper competition on top of 1903 rifles. Brian Dick ... BDL Ltd. - Specializing in British and Commonwealth weapons Specializing in premium ammunition and reloading components. Your source for the finest in High Power Competition Gear. Here at T-bones Shipwrighting we specialise in vintage service rifle: re-barrelling, bedding, repairs, modifications and accurizing. We also provide importation services for firearms, parts and weapons, for both private or commercial businesses.
     

  4. #2
    Contributing Member Singer B's Avatar
    Join Date
    Aug 2019
    Last On
    Yesterday @ 04:14 PM
    Location
    Desert Hot Springs, California
    Posts
    1,053
    Real Name
    Walt Meyer
    Local Date
    03-28-2024
    Local Time
    09:08 AM
    I use the Lubriplate 130-AA on my Garand and both of my M1icon carbines. Never failed me yet and they get used pretty regularly. I don't use it on my other rifles since I save it for the M1. I really only use Hoppes oil on those other guns and maybe some MCarbo grease on the rougher actions (like the MAS-36 I just obtained).
    Last edited by Singer B; 09-25-2020 at 04:04 PM.

  5. Avoid Ads - Become a Contributing Member - Click HERE
  6. #3
    Legacy Member ArizonaBeagle's Avatar
    Join Date
    Apr 2010
    Last On
    04-06-2023 @ 10:33 PM
    Location
    Paradise Valley Arizona
    Posts
    140
    Local Date
    03-28-2024
    Local Time
    07:08 AM

    Grease, Rifle.......

    I have used Lubriplate 630AA for years on Garands, M3-A1, AK's, Brownings and all other military weapons.
    I had used it on printing presses earlier in my life.

    130 AA is calcium based and 630AA is lithium based.

    Their slogan is, "It's the film"

    From their website.......
    LUBRIPLATE No’s. 130-A & 130-AA are designed for those applications where a grease-type lubricant possessing extremely good water repellency and superior lubrication characteristics are desired. These products are recommended for plain bearings, cams, guides, open gears, slides and chassis lubrication and where temperatures do not exceed 170°F. (Note not exceed 170degrees)

    LUBRIPLATE No 630-AAA: is an NLGI No. 0 lubricant, is ideal for centralized lubricating systems. Also excellent for certain types of enclosed gear cases (medium speed – no seals) as the lubricant will re-feed itself into the gear train.
    Product Highlights Water resistant High anti-wear for extra lubricity Oxidation inhibited

    It's really good grease.

    AZB

  7. Thank You to ArizonaBeagle For This Useful Post:


  8. #4
    Legacy Member Orlando's Avatar
    Join Date
    Mar 2009
    Last On
    01-23-2024 @ 05:01 AM
    Location
    Ohio
    Posts
    325
    Local Date
    03-28-2024
    Local Time
    09:08 AM
    Early grease tube, as I remember gas trap era. Unfortunately its not in the best condition



  9. #5
    Legacy Member LavaTech's Avatar
    Join Date
    Mar 2009
    Last On
    01-17-2024 @ 05:29 PM
    Location
    Rural Reno, NV near Palomino Valley at the top of my mountain.
    Age
    65
    Posts
    63
    Local Date
    03-28-2024
    Local Time
    07:08 AM
    There were three rifle grease plastic tubs used that I am aware of. The first is Lubriplate brand marked and has a golden yellow lid with rounded knurl. The tub has a flat bottom with rounded edge. The second is identical to the brand marked tub but is instead marked "GREASE, RIFLE". The tub and knurl is the same. The third has a new container and lid also marked "GREASE, RIFLE" but with concave bottom and squared edge and has a lid that is bright yellow with a very different and easier to grasp knurl.

    If I am not mistaken, the intermediate tubs had remnants of lubriplate inside when I acquired them at Northridge about 12 years ago.
    Last edited by LavaTech; 09-25-2020 at 06:02 PM. Reason: clarity
    Appleseed Project: Where marksmanship meets history and the heritage begins.
    Revolutionary War Veterans Association http://www.appleseedinfo.org/
    Paying Tribute To April 19, 1775 Through Awareness, Learning & Marksmanship.

  10. #6
    Contributing Member Bob Seijas's Avatar
    Join Date
    Mar 2009
    Last On
    Yesterday @ 09:48 PM
    Location
    Montville, NJ and Delray Beach, FL
    Posts
    2,212
    Real Name
    Bob Seijas
    Local Date
    03-28-2024
    Local Time
    10:08 AM

    StanoRust

    I wrote this up in the GCAicon Journal several years ago.Attachment 111265
    Real men measure once and cut.

  11. #7
    Legacy Member Wineman's Avatar
    Join Date
    Aug 2009
    Last On
    03-23-2024 @ 12:25 PM
    Location
    Lodi California
    Posts
    273
    Real Name
    David Crippen
    Local Date
    03-28-2024
    Local Time
    07:08 AM
    Did the M1icon really need the heavy application of grease that we give it today or was the grease a reaction to using the rifle in harsh conditions of water etc.? I know that AR's seem to function better when slathered in lubricant, but the common wisdom is that grease attracts dirt and grit (I use cast bullet wax lube on my bike chains). I have been to CMPicon matches where if a little is good, a lot is much better. I grease mine as instructed, so I'm not a hater, just curious. The CMP website mentions that the rifle was designed to operate with minimal lubrication, but the experience was that it needed more. I have never dragged a rifle through, surf, sand, muck, dirt, ash or any other stoppage material. Just inquisitive about what we accept as gospel and how it came about.

    Dave

  12. #8
    Legacy Member old tanker's Avatar
    Join Date
    Apr 2017
    Last On
    Yesterday @ 10:13 AM
    Location
    Fort Knox, KY
    Age
    74
    Posts
    347
    Real Name
    Emil
    Local Date
    03-28-2024
    Local Time
    10:08 AM
    I also use Lubriplate 630AA for riffle grease,

  13. #9
    Legacy Member Daan Kemp's Avatar
    Join Date
    Jan 2016
    Last On
    Today @ 06:54 AM
    Location
    Centurion RSA
    Age
    73
    Posts
    1,392
    Real Name
    Daan Kemp
    Local Date
    03-28-2024
    Local Time
    04:08 PM
    I also wondered about the minimal lubrication on AR type rifles. The only one I had always worked better with more than recommended gun oil. As to grit, dust, etc, regular cleaning has always been the solution.

  14. #10
    Legacy Member Orlando's Avatar
    Join Date
    Mar 2009
    Last On
    01-23-2024 @ 05:01 AM
    Location
    Ohio
    Posts
    325
    Local Date
    03-28-2024
    Local Time
    09:08 AM
    If you are slathering the garand in grease you are lubricating wrong...................

+ Reply to Thread
Page 1 of 3 1 2 3 LastLast

Similar Threads

  1. Anyone have any Idea the History of this Rifle?
    By Macubus in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 8
    Last Post: 03-18-2017, 04:47 PM
  2. U.S. Plastic Rifle Butt Oiler Incorporating A Grease Pot
    By Flying10uk in forum Milsurps General Discussion Forum
    Replies: 0
    Last Post: 09-14-2016, 05:58 PM
  3. Springfield 1903 history, etc. questions
    By 4Marines in forum M1903/1903A3/A4 Springfield Rifle
    Replies: 4
    Last Post: 02-16-2016, 02:29 AM
  4. A questions on history as it may apply to a 1943 Savage.
    By Rumpelhardt in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 1
    Last Post: 04-17-2011, 10:32 PM
  5. The History of a Rifle
    By miketuite in forum M1903/1903A3/A4 Springfield Rifle
    Replies: 21
    Last Post: 03-09-2010, 12:52 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Raven Rocks