+ Reply to Thread
Page 1 of 2 1 2 LastLast
Results 1 to 10 of 20

Thread: Replacement stock on previously sporterized 1903a3 - several questions

Click here to increase the font size Click here to reduce the font size
  1. #1
    Legacy Member gentwocoog's Avatar
    Join Date
    Dec 2020
    Last On
    03-07-2022 @ 09:07 AM
    Location
    Houston, Texas
    Posts
    8
    Local Date
    03-28-2024
    Local Time
    07:34 AM

    Replacement stock on previously sporterized 1903a3 - several questions

    First post – thanks for letting join this site.

    My dad passed away last year and I inherited his sporterized 1903a3. He took a lot of mule and white tail deer (and maybe an elk or two) with it over the years. While he did a nice job sporterizing the original stock, it doesn’t come close to fitting me (6’3”, 240 lbs, long neck and arms). I’m planning to replace the stock with one from Boyd’s, then bed the action and float the barrel myself.

    Current specs are:
    • Remington-manufactured in 1942
    • Serial number: 41065XX
    • Original 2 groove barrel
    • Dad replaced the trigger with a Timney (very nice break) and added a scope.

    Questions:
    • What is the purpose of the “dual stock reinforcing bolts” on the original rifle?
    • Are these necessary in an aftermarket stock like Boyd’s?
    • From a fit and utility standpoint, am I missing something that might affect restocking the rifle (I’m not very concerned about aesthetics)?
    • Does anyone have experience with Boyd’s aftermarket stocks (good or bad)? Any other sources for completely inletted wood stocks for a 1903a3?

    Side note - due to his health, dad didn't shoot this rifle for the past 15 years minimum. I took it out of the case, loaded it, and bench shot 1 1/4" groups at 100 yards without tweaking a thing. Even with the 2 groove barrel, this is a fine rifle.

    Thanks for your advice – I look forward to providing feedback on the finished project to this board.
    Information
    Warning: This is a relatively older thread
    This discussion is older than 360 days. Some information contained in it may no longer be current.
    Last edited by gentwocoog; 12-08-2020 at 12:51 PM.

  2. Thank You to gentwocoog For This Useful Post:


  3. # ADS
    Friends and Sponsors
    Join Date
    October 2006
    Location
    Milsurps.Com
    Posts
    All Threads
    A Collector's View - The SMLE Short Magazine Lee Enfield 1903-1989. It is 300 8.5x11 inch pages with 1,000+ photo’s, most in color, and each book is serial-numbered.  Covering the SMLE from 1903 to the end of production in India in 1989 it looks at how each model differs and manufacturer differences from a collecting point of view along with the major accessories that could be attached to the rifle. For the record this is not a moneymaker, I hope just to break even, eventually, at $80/book plus shipping.  In the USA shipping is $5.00 for media mail.  I will accept PayPal, Zelle, MO and good old checks (and cash if you want to stop by for a tour!).  CLICK BANNER to send me a PM for International pricing and shipping. Manufacturer of various vintage rifle scopes for the 1903 such as our M73G4 (reproduction of the Weaver 330C) and Malcolm 8X Gen II (Unertl reproduction). Several of our scopes are used in the CMP Vintage Sniper competition on top of 1903 rifles. Brian Dick ... BDL Ltd. - Specializing in British and Commonwealth weapons Specializing in premium ammunition and reloading components. Your source for the finest in High Power Competition Gear. Here at T-bones Shipwrighting we specialise in vintage service rifle: re-barrelling, bedding, repairs, modifications and accurizing. We also provide importation services for firearms, parts and weapons, for both private or commercial businesses.
     

  4. #2
    Advisory Panel browningautorifle's Avatar
    Join Date
    Jul 2008
    Last On
    Yesterday @ 10:05 PM
    Location
    Victoria BC
    Posts
    29,836
    Real Name
    Jim
    Local Date
    03-28-2024
    Local Time
    06:34 AM
    Is the barrel original length and sights? I see the scope mount, if original it shouldn't need headspaced. If that's what you mean by space... Pics would be nice too.
    Regards, Jim

  5. Avoid Ads - Become a Contributing Member - Click HERE
  6. #3
    Legacy Member gentwocoog's Avatar
    Join Date
    Dec 2020
    Last On
    03-07-2022 @ 09:07 AM
    Location
    Houston, Texas
    Posts
    8
    Local Date
    03-28-2024
    Local Time
    07:34 AM
    Thread Starter
    Jim - Yes, the barrel is original length and stamped RA 11-43 at the bore. Any original iron sights have been removed. Apologies, I should have said that I would float the barrel in the new stock. Not replacing the barrel and headspacing is not an issue. I'll see about pics when I can.

    ---------- Post added at 11:50 AM ---------- Previous post was at 11:45 AM ----------

    Steve - the original stock is at least 1 1/2" too short (LOP) (I'm a big guy) and I have to raise my face off the stock about an inch to see through the scope. I thought about spacers (I've used these successfully on shotguns) and a big recoil pad, but that doesn't address the scope issue. Also, I have a hard time with straight grips due to some early arthritis issues in my wrists. This is a rifle that should be shot and I want to be able to shoot it effectively and comfortably.

  7. #4
    Contributing Member ssgross's Avatar
    Join Date
    Jan 2020
    Last On
    Yesterday @ 09:16 PM
    Location
    Virginia
    Posts
    1,517
    Local Date
    03-28-2024
    Local Time
    09:34 AM
    I have fitted 2 Boyd's stocks from CMPicon, and one Minelli from Brownells - so my 2 cents really only applies if you plan to put one of these military stocks on it. If you like it as is, and it's current configuration has sentimental value, than spacers are the way to go. I have even seen some people add blocks inside a slip-on gel recoil pad you can get an extra ~2in, plus the 1in gel this way with no alterations or refinishing.
    On both of the Boyds, the fit was in the action was sloppy and required a lot of work, especially around the tang. The bottom of the tang area was cut very low, but the side walls very high and tight to where you could hear the wood creak when snugging the rear action screw. The flat on the receiver didn't even touch wood, and the front trigger screw bushing (attached to trigger guard) made contact with the recoil lug area to the point that the recoil lug didn't event touch wood. This required moving the whole action back quit a bit. The forearms were also very fat to where the lower band would not slide down at all unless the swivel screw was taken out...stock was way too fat to get the screw back in. Needless to say, it was a lot of work to get right.
    The Minelli stock fit in the action nearly perfect - could call it drop in. All I needed to do to satisfy my OCD was add a touch more clearance behind the tang. The outside, however, was even fatter than the Boyds stocks...but I'd rather work on profiling the outside, and finishing it however I want, then screw around with poor inletting for hours and hours on end any day.
    Just my 2 cents if your plans are to put it back to it's military configuration. I hunt with my 1903a4 Gibbs reproduction. I like carrying my 1903's in the woods way more than anything else.

  8. #5
    Legacy Member gentwocoog's Avatar
    Join Date
    Dec 2020
    Last On
    03-07-2022 @ 09:07 AM
    Location
    Houston, Texas
    Posts
    8
    Local Date
    03-28-2024
    Local Time
    07:34 AM
    Thread Starter

    pictures

    Attachment 113086Attachment 113085Attachment 113087Attachment 113088Attachment 113089

    Here are some quick pictures (definitely not a photographer by trade). Dad did a nice job refinishing the original stock, but it just doesn't fit. For him, it was a deer-killing machine. He bought it surplus after his Army discharge at the end of Korea.

    LOP is 12 3/4" and I need a minimum of 14". You can see how a cheek weld leaves your eyes 1-2" below the scope sight line.
    Last edited by gentwocoog; 12-08-2020 at 01:16 PM.

  9. #6
    Contributing Member ssgross's Avatar
    Join Date
    Jan 2020
    Last On
    Yesterday @ 09:16 PM
    Location
    Virginia
    Posts
    1,517
    Local Date
    03-28-2024
    Local Time
    09:34 AM
    Quote Originally Posted by gentwocoog View Post
    that I would float the barrel in the new stock.
    Also, if you do go with a full length stock, almost all 1903's like upward pressure in the last inch of the forend "barrel bed" area, and no other contact.

    ---------- Post added at 01:16 PM ---------- Previous post was at 01:14 PM ----------

    your pictures show the barrel has been cut down. there should be a slot cut parallel to the bore on top, in front of the date stamp, for the front sight key.

  10. #7
    Legacy Member gentwocoog's Avatar
    Join Date
    Dec 2020
    Last On
    03-07-2022 @ 09:07 AM
    Location
    Houston, Texas
    Posts
    8
    Local Date
    03-28-2024
    Local Time
    07:34 AM
    Thread Starter
    SS - Thanks for your insights re: Boyds and Minelli (I wasn't aware of them and will investigate). It wasn't obvious to me that the barrel had been cut down. Whoever did it did a good job as it isn't noticeable.

    Due to the drop in comb (that's a shotgun term, but I think it translates to rifles. I primarily shoot shotguns and pistols) and wrist arthritis issues, I'm going to go with a pistol grip, combed, aftermarket stock.

    Do you know if the stock reinforcing bolts (you can see these in my pictures) are needed for an aftermarket stock?

    Finally, I've sold off all my father and father-in-law's centerfire rifles except for Dad's 1903a3 and my FIL's 1903a3 (also sporterized, but by a professional). I've shot a lot of deer rifles over the years including some pretty nice ones (FIL had a Weatherby Mark V), but nothing compares to the American Mauser. Those two won't be for sale and will be passed down. Glad you hunt with yours - they're meant to be used.

  11. Thank You to gentwocoog For This Useful Post:


  12. #8
    Contributing Member ssgross's Avatar
    Join Date
    Jan 2020
    Last On
    Yesterday @ 09:16 PM
    Location
    Virginia
    Posts
    1,517
    Local Date
    03-28-2024
    Local Time
    09:34 AM
    I don't think the original 1903 design had stock re-enforcing bolts - they were quickly added after initial testing. You'll find plenty of sporter stocks without them. Another option is to go with a old fashioned leather cheek pad to increase the comb height. Repro's of these are readily available.
    Last edited by ssgross; 12-08-2020 at 02:36 PM.

  13. #9
    Advisory Panel browningautorifle's Avatar
    Join Date
    Jul 2008
    Last On
    Yesterday @ 10:05 PM
    Location
    Victoria BC
    Posts
    29,836
    Real Name
    Jim
    Local Date
    03-28-2024
    Local Time
    06:34 AM
    Quote Originally Posted by gentwocoog View Post
    It wasn't obvious to me that the barrel had been cut down. Whoever did it did a good job as it isn't noticeable.
    But see, you can't fit that barrel with iron sights now. The rear sight goes on the dovetail but if you restock with military wood the best you could do is a faux '03A4 type. Also you need a safety as there's a civilian alteration installed.
    Regards, Jim

  14. #10
    Legacy Member ArtPahl's Avatar
    Join Date
    Jan 2015
    Last On
    03-22-2024 @ 10:51 AM
    Location
    Michigan
    Posts
    192
    Local Date
    03-28-2024
    Local Time
    09:34 AM
    The primary interest of the guys on this forum is to restore these rifles to their original configuration. If I understand your desire correctly, you are interested in using your Dad's A3 as a hunting rifle. I am one of the "old timers" like your Dad, who bought the A3's to convert to hunting rifles. Friends and I did several of them in the 1960's. In those days, Fajen and Bishop made semi finished sporter stocks. Mostly we used those since they were reasonably priced and saved us a lot of work. Both of those outfits were bought up by Midway USAicon and, I believe they are now shut down. In answer to your original question; no, you don't need the cross bolts--you won't be using the rifle for a club or a bayonet handle any more.

    I would suggest you look at Richards Microfit and see if they could fit your needs. I don't know if Boyds makes sporter stocks or not; you might check.

    Your Dad has given you a good start; your Timney trigger already has the safety. He replaced the stamped trigger guard with a milled one from an 03. The bolt handle has been forged for scope clearance.

    I recommend you read up on everything you can find on glass bedding and stock fitting and finishing. You have a fun project on your hands in addition to a labor of love.

    Incidently, not that it matters but one of my books indicates your rifle was produced in December of 1943. It was probably rebarreled in one of the government rebuilding facilities.

    I hope this helps.

+ Reply to Thread
Page 1 of 2 1 2 LastLast

Similar Threads

  1. Remington 1903A3 Sporterized, is it worth reconfiguring to it's former glory?
    By Southpaw_62 in forum M1903/1903A3/A4 Springfield Rifle
    Replies: 6
    Last Post: 02-06-2018, 09:56 AM
  2. 1903a3 with Lyman scope, was a sporterized that was tapped and drilled.
    By Todd2 in forum M1903/1903A3/A4 Springfield Rifle
    Replies: 6
    Last Post: 03-16-2016, 10:42 AM
  3. 1903A3 Rear Sight Removal / Replacement
    By BMorgan1953 in forum M1903/1903A3/A4 Springfield Rifle
    Replies: 6
    Last Post: 01-30-2013, 06:29 PM
  4. Replacement Springfield 1903A3 .30-06 Mil-Spec Barrel from Numrich
    By rugersworld in forum Gunsmithing for Old Milsurps
    Replies: 1
    Last Post: 06-26-2012, 05:23 AM
  5. Sporterized 1903A3
    By sporterized in forum M1903/1903A3/A4 Springfield Rifle
    Replies: 7
    Last Post: 05-06-2012, 01:12 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Raven Rocks