+ Reply to Thread
Page 1 of 2 1 2 LastLast
Results 1 to 10 of 15

Thread: Makeover: De-sportered my 1896 carbine

Click here to increase the font size Click here to reduce the font size
  1. #1
    Legacy Member Warpspasm's Avatar
    Join Date
    Sep 2020
    Last On
    11-06-2021 @ 10:24 PM
    Location
    Maryland
    Posts
    13
    Local Date
    03-28-2024
    Local Time
    06:31 AM

    Makeover: De-sportered my 1896 carbine

    Even though some said "It's a nice sporter, leave it alone." a sporter wasn't what I wanted. I picked this sporter up gun up few weeks a go and after a few prayers went to work. I removed the rubber recoil pad, stripped off the shiny lacquer finish and removed the sling swivels. It was a challenge and I did some things I've never tried before, like shortening a handguard and carving by hand the inlets to allow it to fit over the receiver on one end and under the barrel band on the other. I hand carved an inlet to allow the steel buttplate to fit the stock too. I also plugged holes that were made from aftermarket sling swivels. Finally, I gave her 3 nice coats of BLOicon and ended up with 2 coats of Tom's 1/3 mix. I have to admit, I'm amazed by how well this turned out. Here are some pics. The first one is the rifle before any mods by me. The fifth one is the handguard before I started it's modifications.
    Information
    Warning: This is a relatively older thread
    This discussion is older than 360 days. Some information contained in it may no longer be current.

  2. # ADS
    Friends and Sponsors
    Join Date
    October 2006
    Location
    Milsurps.Com
    Posts
    All Threads
    A Collector's View - The SMLE Short Magazine Lee Enfield 1903-1989. It is 300 8.5x11 inch pages with 1,000+ photo’s, most in color, and each book is serial-numbered.  Covering the SMLE from 1903 to the end of production in India in 1989 it looks at how each model differs and manufacturer differences from a collecting point of view along with the major accessories that could be attached to the rifle. For the record this is not a moneymaker, I hope just to break even, eventually, at $80/book plus shipping.  In the USA shipping is $5.00 for media mail.  I will accept PayPal, Zelle, MO and good old checks (and cash if you want to stop by for a tour!).  CLICK BANNER to send me a PM for International pricing and shipping. Manufacturer of various vintage rifle scopes for the 1903 such as our M73G4 (reproduction of the Weaver 330C) and Malcolm 8X Gen II (Unertl reproduction). Several of our scopes are used in the CMP Vintage Sniper competition on top of 1903 rifles. Brian Dick ... BDL Ltd. - Specializing in British and Commonwealth weapons Specializing in premium ammunition and reloading components. Your source for the finest in High Power Competition Gear. Here at T-bones Shipwrighting we specialise in vintage service rifle: re-barrelling, bedding, repairs, modifications and accurizing. We also provide importation services for firearms, parts and weapons, for both private or commercial businesses.
     

  3. #2
    Advisory Panel browningautorifle's Avatar
    Join Date
    Jul 2008
    Last On
    Yesterday @ 10:05 PM
    Location
    Victoria BC
    Posts
    29,836
    Real Name
    Jim
    Local Date
    03-28-2024
    Local Time
    03:31 AM
    Looks good now, I understand not wanting in sporting config. I forget, did you say the bore was nice? I'd expect it was as those were the ones chosen for hunting rifles, not ugly bores.
    Regards, Jim

  4. Avoid Ads - Become a Contributing Member - Click HERE
  5. #3
    Legacy Member Warpspasm's Avatar
    Join Date
    Sep 2020
    Last On
    11-06-2021 @ 10:24 PM
    Location
    Maryland
    Posts
    13
    Local Date
    03-28-2024
    Local Time
    06:31 AM
    Thread Starter
    Quote Originally Posted by browningautorifleicon View Post
    Looks good now, I understand not wanting in sporting config. I forget, did you say the bore was nice? I'd expect it was as those were the ones chosen for hunting rifles, not ugly bores.
    The bore is almost pristine.

  6. Thank You to Warpspasm For This Useful Post:


  7. #4
    Advisory Panel browningautorifle's Avatar
    Join Date
    Jul 2008
    Last On
    Yesterday @ 10:05 PM
    Location
    Victoria BC
    Posts
    29,836
    Real Name
    Jim
    Local Date
    03-28-2024
    Local Time
    03:31 AM
    Quote Originally Posted by Warpspasm View Post
    almost pristine
    Makes it even better then.
    Regards, Jim

  8. #5
    Legacy Member Salt Flat's Avatar
    Join Date
    Nov 2011
    Last On
    Yesterday @ 03:57 PM
    Location
    USA
    Posts
    760
    Local Date
    03-28-2024
    Local Time
    03:31 AM
    Wow! That worked out great-- another one saved. Salt Flat

  9. #6
    Legacy Member HOOKED ON HISTORY's Avatar
    Join Date
    Mar 2011
    Last On
    Yesterday @ 06:06 PM
    Location
    MS/USA
    Posts
    3,991
    Local Date
    03-28-2024
    Local Time
    05:31 AM
    CPR worked on that one. Very nice work!


    CPR = Cost Prohibitive Restoration.
    Sometimes its not about the money.

  10. #7
    Legacy Member jon_norstog's Avatar
    Join Date
    Mar 2009
    Last On
    11-01-2021 @ 12:41 AM
    Location
    Portland, Oregon
    Age
    78
    Posts
    582
    Local Date
    03-28-2024
    Local Time
    03:31 AM
    Well it came out very nice! I like the horns on the barrel band - for use with a scabbard I guess. Can you do something about the front sight?

    jn

  11. #8
    Legacy Member Warpspasm's Avatar
    Join Date
    Sep 2020
    Last On
    11-06-2021 @ 10:24 PM
    Location
    Maryland
    Posts
    13
    Local Date
    03-28-2024
    Local Time
    06:31 AM
    Thread Starter
    Quote Originally Posted by jon_norstog View Post
    Well it came out very nice! I like the horns on the barrel band - for use with a scabbard I guess. Can you do something about the front sight?

    jn
    I'm still trying to decide what to do with the front sight. I'm just afraid of what's under that band and opening up a can of worms. I also still need to do something about a handguard spring clip and riveting it to the hand guard. That worries me too. LOL

  12. #9
    Advisory Panel browningautorifle's Avatar
    Join Date
    Jul 2008
    Last On
    Yesterday @ 10:05 PM
    Location
    Victoria BC
    Posts
    29,836
    Real Name
    Jim
    Local Date
    03-28-2024
    Local Time
    03:31 AM
    Quote Originally Posted by Warpspasm View Post
    I'm still trying to decide what to do with the front sight.
    I'll bet it's sweated or just press fitted. Do you SEE a key or cross pin there?
    Regards, Jim

  13. #10
    Legacy Member Warpspasm's Avatar
    Join Date
    Sep 2020
    Last On
    11-06-2021 @ 10:24 PM
    Location
    Maryland
    Posts
    13
    Local Date
    03-28-2024
    Local Time
    06:31 AM
    Thread Starter
    Quote Originally Posted by browningautorifleicon View Post
    I'll bet it's sweated or just press fitted. Do you SEE a key or cross pin there?
    I think you're probably correct about being sweated or press fitted. My concern is more about the condition of the barrel finish under the band, but mainly about what I put on there to replace the sight I have. Ideally, it would be real carbine front sight, but they're pretty much impossible to find and crazy expensive if do find one. I think I read that you can use a Springfield 1903 front sight, but I'm not certain about that. I want to do something though, and I'm open to suggestions.

    I'm sure most of us know, it's easy when you fool with this kind of stuff to get carried away with putting too much money into something that really has limited collector value. In the case of this carbine, unfortunately, whoever turned it into a sporter did a professional job and sanded the carbine stock to remove all of the markings, bobbed the butt .3" to fit a rubber recoil pad, and used what is probably a shortened rifle barrel (in great shape by the way). Who knows about the receiver? I've come to the conclusion that nobody knows for sure what range of serial numbers really covered the carbines. On the OTHER hand, many of us know these kind of projects aren't just about collector value. It's the challenge to make them as close as possible to an original and personalize them for your liking. The trick is knowing when to stop. So far, I'm still struggling with that trick. HAHAHAHA.

+ Reply to Thread
Page 1 of 2 1 2 LastLast

Similar Threads

  1. 1896 Carbine
    By Dadx3 in forum Krag Rifles
    Replies: 8
    Last Post: 04-06-2018, 12:00 AM
  2. 1896 Krag Carbine
    By 1563621 in forum Krag Rifles
    Replies: 1
    Last Post: 09-25-2016, 10:20 AM
  3. 1896 carbine
    By rice 123 in forum Krag Rifles
    Replies: 2
    Last Post: 02-20-2013, 07:21 PM
  4. RIC Carbine 1896
    By rkh in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 7
    Last Post: 03-26-2011, 06:56 PM
  5. Is my mod 1896 30-40 a carbine or rifle?
    By diggerdirect in forum Krag Rifles
    Replies: 3
    Last Post: 03-05-2010, 12:25 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Raven Rocks