+ Reply to Thread
Results 1 to 5 of 5

Thread: To steam or to boil. That is my question.

Click here to increase the font size Click here to reduce the font size
  1. #1
    Legacy Member gonzogeezer's Avatar
    Join Date
    Jun 2016
    Last On
    01-12-2024 @ 03:16 PM
    Location
    Harrisburg, PA
    Posts
    19
    Local Date
    03-18-2024
    Local Time
    11:45 PM

    To steam or to boil. That is my question.

    Hello All, I have managed to accumulate a bit of a pile of milsurp and other old pistols. I can’t resist an old .32. I think some of them Willkie benefit from some
    conservation, specifically trying to restore what can be restored I f the original finish. I’ve read the threads up here, watched all of Mark Novak’s Anvil YouTube videos on the subject. But I see here and from Mark that sometimes people steam the parts, sometimes they boil the parts, and sometimes they even do both.

    What is the rule? Is there a rule?

    Thanks.
    Information
    Warning: This is a relatively older thread
    This discussion is older than 360 days. Some information contained in it may no longer be current.

  2. # ADS
    Friends and Sponsors
    Join Date
    October 2006
    Location
    Milsurps.Com
    Posts
    All Threads
    A Collector's View - The SMLE Short Magazine Lee Enfield 1903-1989. It is 300 8.5x11 inch pages with 1,000+ photo’s, most in color, and each book is serial-numbered.  Covering the SMLE from 1903 to the end of production in India in 1989 it looks at how each model differs and manufacturer differences from a collecting point of view along with the major accessories that could be attached to the rifle. For the record this is not a moneymaker, I hope just to break even, eventually, at $80/book plus shipping.  In the USA shipping is $5.00 for media mail.  I will accept PayPal, Zelle, MO and good old checks (and cash if you want to stop by for a tour!).  CLICK BANNER to send me a PM for International pricing and shipping. Manufacturer of various vintage rifle scopes for the 1903 such as our M73G4 (reproduction of the Weaver 330C) and Malcolm 8X Gen II (Unertl reproduction). Several of our scopes are used in the CMP Vintage Sniper competition on top of 1903 rifles. Brian Dick ... BDL Ltd. - Specializing in British and Commonwealth weapons Specializing in premium ammunition and reloading components. Your source for the finest in High Power Competition Gear. Here at T-bones Shipwrighting we specialise in vintage service rifle: re-barrelling, bedding, repairs, modifications and accurizing. We also provide importation services for firearms, parts and weapons, for both private or commercial businesses.
     

  3. #2
    Contributing Member mmppres's Avatar
    Join Date
    Mar 2014
    Last On
    02-14-2024 @ 11:14 AM
    Location
    butler pa
    Age
    58
    Posts
    1,080
    Real Name
    mike
    Local Date
    03-18-2024
    Local Time
    11:45 PM
    I have restored alot of different firearms. Never really boiled them. Soaked the parts in a degreaser type liquid like purple power(very cheap) Then use your good thinner an finish.

  4. Avoid Ads - Become a Contributing Member - Click HERE
  5. #3
    Legacy Member gonzogeezer's Avatar
    Join Date
    Jun 2016
    Last On
    01-12-2024 @ 03:16 PM
    Location
    Harrisburg, PA
    Posts
    19
    Local Date
    03-18-2024
    Local Time
    11:45 PM
    Thread Starter
    I don’t see how that can convert rust.

  6. #4
    Contributing Member ssgross's Avatar
    Join Date
    Jan 2020
    Last On
    Yesterday @ 09:35 PM
    Location
    Virginia
    Posts
    1,514
    Local Date
    03-19-2024
    Local Time
    12:45 AM
    Quote Originally Posted by gonzogeezer View Post
    sometimes people steam the parts, sometimes they boil the parts, and sometimes they even do both.
    If conserving by getting rid of red iron oxide without damaging the underlying finish (black iron oxide), either steaming or boiling should work just fine.
    Steaming seems to convert faster. In my opinion, boiling is easier to get right every time...it's like the difference between smoking a pork butt vs. something delicate. I've done both boiling and steaming, but with rust blueing, both from scratch on bare metal as well as adding new rust bluing over top of existing finish to darken or fill in worn spots. My results with steaming were always blotchy - like a car you just washed but let it sit and air dry - even after a several dozen iterations. Some people say steam and report it works for them - the guy at rustblue.com even has a paragraph on his site about preferring steaming with some loose reasoning. I've tried steaming a dozen times now, on a full barrel as well as a receiver and small parts. I've tried preheating the metal to 220F or so before steaming. I've tried introducing the part after the steam is roaring. Nothing ever works. There is always some condensation on the metal from the steam, and that results in disturbing the fine layer of rust, and thus blotchy spots. Some say they fill in with subsequent iterations as the black oxide evens out. I say hogwash. Tried it with 30+ iterations. The spots and rings do subside, but wouldn't go away and were still very noticeable no matter what. Every time I tried to steam, I ended up sanding back to bare metal and doing it again with boiling. Maybe I just don't know what I'm doing. If it works for someone out there or they swear by it, good for them go give yourself a cookie.

    I've never had any blotchiness rust bluing with boiling. Also, guys will say steaming is the cheaper route to go...no tank to buy, just get your pvc tube and cheap pot with lid and hot plate or burner. I say hogwash to that too. My boil setup is a 4" cellular pvc pipe, with a short 1500w water heater element screwed in the bottom. Element is 7.99 at Lowes. black iron nipple and coupler are used as there are only 3 threads on the element and with so little you can't get it tight enough in the pvc without stripping the plastic threads. $10 for the iron fittings, and the male half from an old extension cord. I soldered the ground wire to the iron fitting, then wrapped all tight in vinyl tape just in case there was a leak.
    Attachment 120127
    I used a scrap square of plywood with a hole cut, and some scrap 2x4 blocks to set it on. I then used a bungie cord to attach it to the rail of my back porch. The pvc softens after a while, and there is a mark from the bungie cord. But, after a hundred boils it still works just fine. In fact, I have it plugged in to a temp sensor so it stays at 210 while I apply the next coat solution of express blue. That way it's roaring boil in a couple seconds when I'm ready. Ran it like this for an entire weekend day and night...I had a lot of bluing to do...still using the same tube. No leaks. My first attempt was without the iron fittings. Got 2 boils before the threads started leaking.
    Last edited by ssgross; 09-15-2021 at 09:32 PM.

  7. The Following 5 Members Say Thank You to ssgross For This Useful Post:


  8. #5
    Contributing Member ssgross's Avatar
    Join Date
    Jan 2020
    Last On
    Yesterday @ 09:35 PM
    Location
    Virginia
    Posts
    1,514
    Local Date
    03-19-2024
    Local Time
    12:45 AM
    Well...I thought I might add one more point I just learned. My 1903a3 barreled action came back today from a parkerizing job. I had all my parts ready to go for assembly tonight, and I fit the stock before sending the action out. When I blued the parts a month ago, I boiled the cocking piece bolt collar, striker, and the little sleeve behind the striker. I don't like to have too many parts going all at once, so I did 8 iterations on these, and left them submerged in container of WD-40 while I did the safety lever, magazine cutoff, trigger, sear, and the floor plate from the milled bottom metal I was going to use. My water in the pot had gone down, so I put the steamer basket in and steamed this second round. They turned out fine, and I submerged them in the wd-40 and left it all there overnight. Next morning I wiped all the excess off the parts, and set them off to the side in a plastic container to wait on the action to come back.

    Well, there were noticeable blotches of surface rust on the floor plate, trigger, safety lever, and magazine cutoff, and none on any of the parts that were boiled. Lesson learned, steaming requires a final rinse or a boil to neutralize any residue left on the metal after the last iteration. The rust was very fine, and carded off with oil and steel wool without a trace left behind.

    I had forgotten I was still working on removing the pitting and sanding the trigger gaurd and so it is still in the white. When I blue it this weekend, I'll give all the parts a final boil in clean distilled water + baking soda to be safe.

+ Reply to Thread

Similar Threads

  1. How do you steam out dings and dents from walnut stocks?
    By Scott in Indiana in forum M1 Garand/M14/M1A Rifles
    Replies: 35
    Last Post: 12-13-2013, 05:25 PM
  2. Question about a question mark
    By Demo in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 5
    Last Post: 07-12-2011, 05:11 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Raven Rocks