+ Reply to Thread
Results 1 to 8 of 8

Thread: my cleaned up 1873 Springfield

Click here to increase the font size Click here to reduce the font size
  1. #1
    Contributing Member ssgross's Avatar
    Join Date
    Jan 2020
    Last On
    Yesterday @ 09:35 PM
    Location
    Virginia
    Posts
    1,514
    Local Date
    03-19-2024
    Local Time
    04:04 AM

    my cleaned up 1873 Springfield

    Finally got some cases loaded and some time at the range on my way home from work. Fun evening.
    Here is the thread where I sourced, acquired, and cleaned up this treasure.
    https://www.milsurps.com/showthread.php?t=73637
    Attachment 120642Attachment 120643
    New starling brass from Midway. I found 20-1 alloy bullets at https://www.buffaloarms.com
    a few months ago, but all they had in stock at the time were 0.458, 395gr round nose from Lyman bullet mold 457124. I used my Lee manual for data, which listed loads for 385gr and 405gr cast bullets with IMR4064, which I have plenty of. I conservatively interpolated between the starting loads with 44gr.

    The target above was at 25 yards. My Labradar showed an average of 1590-1617 fps, with a standard deviation of 8fps...so I think I did my job loading! I was expecting about 1275fps based on what the manual said. Also, at 25yds I was impacting 8 inches or so high. in that group I was aiming at the bottom of the target backer to keep it on paper. I had the sight all the way down at the bottom (100yd marking). Making a drop chart from what I saw at 25yds predicted I was zeroed for ~350yds, and would hit >24 inches high at 100yds, which is the extent of my indoor facilities. So, after 3 rounds aiming on the floor at 100 yds just to see a hole on paper, I went back to being content at 25yds for this trip.

    BuffaloArms now has 500gr RN from Saeco Mould 1881. I just bought 6 boxes, and it now says out of stock. Now that I have a starting point, I'll dial down my loads for the 395 grainers to get something close to the original ballistics of 1350fps of 405gr. This should help my problem of shooting so high, e.g. at 1275fps a 100 yd zero would have meant only 1inch high at 25 yds. By the way, my bore slugs at a perfect .458, and is in perfect condition!
    Information
    Warning: This is a relatively older thread
    This discussion is older than 360 days. Some information contained in it may no longer be current.

  2. # ADS
    Friends and Sponsors
    Join Date
    October 2006
    Location
    Milsurps.Com
    Posts
    All Threads
    A Collector's View - The SMLE Short Magazine Lee Enfield 1903-1989. It is 300 8.5x11 inch pages with 1,000+ photo’s, most in color, and each book is serial-numbered.  Covering the SMLE from 1903 to the end of production in India in 1989 it looks at how each model differs and manufacturer differences from a collecting point of view along with the major accessories that could be attached to the rifle. For the record this is not a moneymaker, I hope just to break even, eventually, at $80/book plus shipping.  In the USA shipping is $5.00 for media mail.  I will accept PayPal, Zelle, MO and good old checks (and cash if you want to stop by for a tour!).  CLICK BANNER to send me a PM for International pricing and shipping. Manufacturer of various vintage rifle scopes for the 1903 such as our M73G4 (reproduction of the Weaver 330C) and Malcolm 8X Gen II (Unertl reproduction). Several of our scopes are used in the CMP Vintage Sniper competition on top of 1903 rifles. Brian Dick ... BDL Ltd. - Specializing in British and Commonwealth weapons Specializing in premium ammunition and reloading components. Your source for the finest in High Power Competition Gear. Here at T-bones Shipwrighting we specialise in vintage service rifle: re-barrelling, bedding, repairs, modifications and accurizing. We also provide importation services for firearms, parts and weapons, for both private or commercial businesses.
     

  3. #2
    Contributing Member ssgross's Avatar
    Join Date
    Jan 2020
    Last On
    Yesterday @ 09:35 PM
    Location
    Virginia
    Posts
    1,514
    Local Date
    03-19-2024
    Local Time
    04:04 AM
    Thread Starter
    For anyone out there with a LabRadar...I'll save you similar frustration by saying don't forget to change your settings to pistol velocities instead of rifle, otherwise you will get the dreaded "shot cannot be tracked" error. It worked flawlessly after I figured that out.

  4. Avoid Ads - Become a Contributing Member - Click HERE
  5. #3
    Contributing Member ssgross's Avatar
    Join Date
    Jan 2020
    Last On
    Yesterday @ 09:35 PM
    Location
    Virginia
    Posts
    1,514
    Local Date
    03-19-2024
    Local Time
    04:04 AM
    Thread Starter
    Hey, Jim, hoping your luck will continue...can you check the SRS for 168171? Maybe this rifle has a greater chance of a hit given it had rack numbers.

  6. #4
    Advisory Panel browningautorifle's Avatar
    Join Date
    Jul 2008
    Last On
    Today @ 12:35 AM
    Location
    Victoria BC
    Posts
    29,813
    Real Name
    Jim
    Local Date
    03-19-2024
    Local Time
    01:04 AM
    Quote Originally Posted by ssgross View Post
    SRS for 168171

    Nothing even close to that number in SRS #1...
    Regards, Jim

  7. Thank You to browningautorifle For This Useful Post:


  8. #5
    Contributing Member ssgross's Avatar
    Join Date
    Jan 2020
    Last On
    Yesterday @ 09:35 PM
    Location
    Virginia
    Posts
    1,514
    Local Date
    03-19-2024
    Local Time
    04:04 AM
    Thread Starter
    Twas worth a try. My 500 grainers came in. Those should match my rear sight as long as I get the velocity right.

  9. Thank You to ssgross For This Useful Post:


  10. #6
    Advisory Panel browningautorifle's Avatar
    Join Date
    Jul 2008
    Last On
    Today @ 12:35 AM
    Location
    Victoria BC
    Posts
    29,813
    Real Name
    Jim
    Local Date
    03-19-2024
    Local Time
    01:04 AM
    I tried those through a Ruger #3, an 1886 Winchester and a Marlin 1895 with no satisfactory effect...they were cast wheel weight but maybe just too long for my twist. I'll never know.
    Regards, Jim

  11. #7
    Contributing Member ssgross's Avatar
    Join Date
    Jan 2020
    Last On
    Yesterday @ 09:35 PM
    Location
    Virginia
    Posts
    1,514
    Local Date
    03-19-2024
    Local Time
    04:04 AM
    Thread Starter
    Quote Originally Posted by browningautorifleicon View Post
    with no satisfactory effect...they were cast wheel weight but maybe just too long for my twist. I'll never know.
    I have no experience with those firearms. From what I'm reading, wheel weights were in the range of ~10-1 antimony. "The Book" (Wolfe https://the4570book.com) specifically says to run away from anything with antimony in it for trapdoors, and to stick with the 20-1 tin, or less tin, for best accuracy. I have high hopes for these, but I'll be happy so long as I don't have to aim at the floor to get on paper like the others

    Been thinking about casting for myself over the last year...but the highly prized saeco 1881 mould has not presented itself.
    Last edited by ssgross; 10-19-2021 at 09:59 AM.

  12. #8
    Contributing Member ssgross's Avatar
    Join Date
    Jan 2020
    Last On
    Yesterday @ 09:35 PM
    Location
    Virginia
    Posts
    1,514
    Local Date
    03-19-2024
    Local Time
    04:04 AM
    Thread Starter
    Took this trapdoor back to the range tonight...with 20 rounds of 0.458, 500gr round nose, 20-1 alloy form buffaloarms.com. Here is tonights data.
    45-70-500
    Historical target (Wolfe's book): 1315 FPS, minimum acceptable 1270
    My results:
    500gr, 20-1 soft cast over 39gr. IMR4064
    MV average: 1305
    Min: 1262, Max 1339
    SD 17.8

    Took some cross-referencing between all my manuals to make this starting point. I'd say I darn near duplicated the original target!

    At 100yds, I put 4 out of 5 of these rounds within 2 inches of each other. I messed up the third shot and it flew 2 in. right of the group. My group impacted 12 inches above my point of aim, and 3 inches right. The M1879 sight was set all the way down. I double checked my front sight post and it is a perfect 0.100 above it's base...exactly what it is supposed to be. This load was very fun to shoot. Next trip I need to make sure my tape measure is in the bag so I can paste my "aiming" target in the exact spot needed to get me all over the bull.

    Maybe a third of my cases are showing pierced primers, the rest are fine. Instead of shelling out hundreds on the thicker skinned primers or magnum primers, I may purchase another firing pin and adjust it's max protrusion. They can be had ~$20.

    EDIT: Track of the wolf has the LEE M1873, 405gr hollow base mould back in stock. I got me one. I have no pot, no lead...but I have a mould now!

+ Reply to Thread

Similar Threads

  1. Help with identification on a Springfield Trap 1873
    By sllimb in forum Other U.S. Service Rifles
    Replies: 4
    Last Post: 12-21-2019, 02:59 PM
  2. Dating a Springfield 1873 TD ...
    By M100C in forum Other U.S. Service Rifles
    Replies: 5
    Last Post: 12-29-2017, 11:10 AM
  3. 1873 Springfield Trapdoor 45/70
    By invaliduser in forum Other U.S. Service Rifles
    Replies: 2
    Last Post: 11-03-2014, 09:06 AM
  4. Springfield 1873 Trapdoor help please.
    By Inverted99 in forum Other U.S. Service Rifles
    Replies: 13
    Last Post: 02-19-2012, 10:14 PM
  5. Springfield 1873 Mfg. Date
    By dshepnh in forum The Watering Hole OT (Off Topic) Forum
    Replies: 4
    Last Post: 03-29-2009, 07:41 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Raven Rocks