+ Reply to Thread
Results 1 to 6 of 6

Thread: Firing pin?

Click here to increase the font size Click here to reduce the font size
  1. #1
    Contributing Member ssgross's Avatar
    Join Date
    Jan 2020
    Last On
    Yesterday @ 09:16 PM
    Location
    Virginia
    Posts
    1,517
    Local Date
    03-28-2024
    Local Time
    08:42 AM

    Firing pin?

    My first times to the range with my trapdoor showed a mix of primers that split open.
    Attachment 121030Attachment 121031Attachment 121032Attachment 121033
    Took the pin out, and looks like there is some deformation in the tip...looks like previous pitting. The second 2 cases that didn't split show the imprint of the deformation.
    Attachment 121034Attachment 121035
    sorry, it's a hard part to focus the camera on. I don't think my loads were too hot...details are in my range report here. I remember the first time out, the very first round split, the next 4 did not. Leaves me to believe the I should have inspected the pin closer when I disassembled and cleaned it up. Cleanup thread is here

    I have another firing pin on the way from the quartermaster's store as a backup while I try to save this one by stoning it nice and round again.
    Information
    Warning: This is a relatively older thread
    This discussion is older than 360 days. Some information contained in it may no longer be current.

  2. # ADS
    Friends and Sponsors
    Join Date
    October 2006
    Location
    Milsurps.Com
    Posts
    All Threads
    A Collector's View - The SMLE Short Magazine Lee Enfield 1903-1989. It is 300 8.5x11 inch pages with 1,000+ photo’s, most in color, and each book is serial-numbered.  Covering the SMLE from 1903 to the end of production in India in 1989 it looks at how each model differs and manufacturer differences from a collecting point of view along with the major accessories that could be attached to the rifle. For the record this is not a moneymaker, I hope just to break even, eventually, at $80/book plus shipping.  In the USA shipping is $5.00 for media mail.  I will accept PayPal, Zelle, MO and good old checks (and cash if you want to stop by for a tour!).  CLICK BANNER to send me a PM for International pricing and shipping. Manufacturer of various vintage rifle scopes for the 1903 such as our M73G4 (reproduction of the Weaver 330C) and Malcolm 8X Gen II (Unertl reproduction). Several of our scopes are used in the CMP Vintage Sniper competition on top of 1903 rifles. Brian Dick ... BDL Ltd. - Specializing in British and Commonwealth weapons Specializing in premium ammunition and reloading components. Your source for the finest in High Power Competition Gear. Here at T-bones Shipwrighting we specialise in vintage service rifle: re-barrelling, bedding, repairs, modifications and accurizing. We also provide importation services for firearms, parts and weapons, for both private or commercial businesses.
     

  3. #2
    Legacy Member Daan Kemp's Avatar
    Join Date
    Jan 2016
    Last On
    Today @ 06:54 AM
    Location
    Centurion RSA
    Age
    73
    Posts
    1,392
    Real Name
    Daan Kemp
    Local Date
    03-28-2024
    Local Time
    02:42 PM
    Too soft primers?

  4. Avoid Ads - Become a Contributing Member - Click HERE
  5. #3
    Advisory Panel browningautorifle's Avatar
    Join Date
    Jul 2008
    Last On
    Yesterday @ 10:05 PM
    Location
    Victoria BC
    Posts
    29,836
    Real Name
    Jim
    Local Date
    03-28-2024
    Local Time
    05:42 AM
    I kind of side with you on too much protrusion. There must be spec at hand somewhere here for firing pin protrusion...the ones that didn't pierce are right to the bottom and that ain't right. The firing pin in it could have been put in any time over the last 150 years and needs tiddled up. Just polish it round and see. I've worked with Federal primers for years and don't see that, they're soft.
    Regards, Jim

  6. #4
    Contributing Member ssgross's Avatar
    Join Date
    Jan 2020
    Last On
    Yesterday @ 09:16 PM
    Location
    Virginia
    Posts
    1,517
    Local Date
    03-28-2024
    Local Time
    08:42 AM
    Thread Starter
    Quote Originally Posted by browningautorifleicon View Post
    I've worked with Federal primers for years and don't see that, they're soft.
    The issue is discussed in other forums. In many cases, with no spring on the pin the primer gets driven back flush against the bolt face, and the "larger" trapdoor firing pin hole acts like a cookie cutter and the middle part of the primer blows. I thankfully don't have that problem. Other instances there were burrs or deformation on the pin tip, other instances a combination of these two problems.
    The primers don't show any flat area from working out rearward. 5 out of 20 means I think you are right Jim. Just polish up the tip nice and round and should be good to go.

  7. #5
    Contributing Member ssgross's Avatar
    Join Date
    Jan 2020
    Last On
    Yesterday @ 09:16 PM
    Location
    Virginia
    Posts
    1,517
    Local Date
    03-28-2024
    Local Time
    08:42 AM
    Thread Starter
    that was easy...just chucked the pin in the drill press and worked the tip round with cloth backed paper.
    Attachment 121044
    maybe someone who doesn't have this problem at all can measure the protrusion of their pin for comparison?

  8. #6
    Contributing Member Low & Slow's Avatar
    Join Date
    May 2015
    Last On
    Yesterday @ 11:25 PM
    Location
    colorado usa
    Posts
    342
    Local Date
    03-28-2024
    Local Time
    06:42 AM
    Recently had my 1873 apart, and was disconcerted to find the firing pin had become a two-piece affair. Found an original replacement. Test firing was satisfactory. Full protrusion is just shy of .090" as best I can measure without further tear down. Hope that's of some use.

  9. Thank You to Low & Slow For This Useful Post:


+ Reply to Thread

Similar Threads

  1. Firing Pin N-S or S-N
    By painter777 in forum M1/M2 Carbine
    Replies: 3
    Last Post: 12-26-2020, 02:22 PM
  2. firing pin
    By philb in forum Milsurps General Discussion Forum
    Replies: 3
    Last Post: 02-19-2018, 03:42 AM
  3. NO 4 firing pin
    By Doco overboard in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 10
    Last Post: 07-23-2017, 10:03 PM
  4. T38 5 7/16 in firing pin?
    By doodlebug in forum Japanese Rifles
    Replies: 2
    Last Post: 03-15-2016, 06:30 PM
  5. Enfield firing pin, firing pin spring compatibility SMLE vs No. 4 & other questions
    By Steve762 in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 2
    Last Post: 01-02-2015, 06:55 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Raven Rocks