+ Reply to Thread
Results 1 to 8 of 8

Thread: How Clean Does Brass Used with Blackpowder Need to Get?

Click here to increase the font size Click here to reduce the font size
  1. #1
    Legacy Member RossMkIIEnjoyer's Avatar
    Join Date
    Nov 2021
    Last On
    03-18-2024 @ 12:56 PM
    Location
    Kentucky, USA
    Posts
    39
    Local Date
    03-28-2024
    Local Time
    08:03 AM

    How Clean Does Brass Used with Blackpowder Need to Get?

    Hi,
    I fired my first blackpowder cartridge handloads yesterday and began cleaning immediately. I rinsed my cases, decapped them, then soaked them in hot water with some dawn dish soap. I then dried them and tumbled them. After maybe 12 hours they were shiny on the outside again but the primer pockets and the bottom of inside the cases still have black spots. I soaked them again today and they are in the tumbler again while I sleep.

    Is it normal to not get every speck of blackpowder residue out? Will the life of these shells be cut short? Or am I concerned about nothing?
    Information
    Warning: This is a relatively older thread
    This discussion is older than 360 days. Some information contained in it may no longer be current.

  2. # ADS
    Friends and Sponsors
    Join Date
    October 2006
    Location
    Milsurps.Com
    Posts
    All Threads
    A Collector's View - The SMLE Short Magazine Lee Enfield 1903-1989. It is 300 8.5x11 inch pages with 1,000+ photo’s, most in color, and each book is serial-numbered.  Covering the SMLE from 1903 to the end of production in India in 1989 it looks at how each model differs and manufacturer differences from a collecting point of view along with the major accessories that could be attached to the rifle. For the record this is not a moneymaker, I hope just to break even, eventually, at $80/book plus shipping.  In the USA shipping is $5.00 for media mail.  I will accept PayPal, Zelle, MO and good old checks (and cash if you want to stop by for a tour!).  CLICK BANNER to send me a PM for International pricing and shipping. Manufacturer of various vintage rifle scopes for the 1903 such as our M73G4 (reproduction of the Weaver 330C) and Malcolm 8X Gen II (Unertl reproduction). Several of our scopes are used in the CMP Vintage Sniper competition on top of 1903 rifles. Brian Dick ... BDL Ltd. - Specializing in British and Commonwealth weapons Specializing in premium ammunition and reloading components. Your source for the finest in High Power Competition Gear. Here at T-bones Shipwrighting we specialise in vintage service rifle: re-barrelling, bedding, repairs, modifications and accurizing. We also provide importation services for firearms, parts and weapons, for both private or commercial businesses.
     

  3. #2
    Advisory Panel browningautorifle's Avatar
    Join Date
    Jul 2008
    Last On
    Yesterday @ 10:05 PM
    Location
    Victoria BC
    Posts
    29,836
    Real Name
    Jim
    Local Date
    03-28-2024
    Local Time
    06:03 AM
    Quote Originally Posted by Steve762 View Post
    Pin tumbling seems to be replacing corn cob media tumbling/vibrating
    That's what I use and would recommend. Three hours works and returns the brass to new look. Dump your brass into the soapy solution on the firing line as soon as possible. The firing action has already driven the powder into the brass but that will prolong it's life.

    When using the stainless steel pins and lemme shine and dawn, a little is better than a lot. Literally a few drops of dawn and a teaspoon of lemme shine or your brass will tarnish again as soon as it's dry. More is not better. I also start with hot water and rinse with hot water.
    Last edited by browningautorifle; 07-20-2022 at 09:22 AM.
    Regards, Jim

  4. Thank You to browningautorifle For This Useful Post:


  5. Avoid Ads - Become a Contributing Member - Click HERE
  6. #3
    Legacy Member RossMkIIEnjoyer's Avatar
    Join Date
    Nov 2021
    Last On
    03-18-2024 @ 12:56 PM
    Location
    Kentucky, USA
    Posts
    39
    Local Date
    03-28-2024
    Local Time
    08:03 AM
    Thread Starter
    Thanks,
    I looked at a wet tumbler with the stainless pins but didn't want to spend the money. Looks like once I can swing it, I'll have to get one. I currently have a vibratory tumbler with fresh corn cob media. I was going to put extra polishing compound in but all that I had left was a couple drops. The brass looks fairly clean now but I'll have to keep an eye on it I guess. I wouldn't be so worried if these shells weren't so expensive and didn't have such a lead time.

  7. #4
    Advisory Panel browningautorifle's Avatar
    Join Date
    Jul 2008
    Last On
    Yesterday @ 10:05 PM
    Location
    Victoria BC
    Posts
    29,836
    Real Name
    Jim
    Local Date
    03-28-2024
    Local Time
    06:03 AM
    Quote Originally Posted by RossMkIIEnjoyer View Post
    I looked at a wet tumbler with the stainless pins but didn't want to spend the money.
    I understand you completely and had the exact same thoughts years ago. Then I would endure hours of vibra tumbling when my media started to degrade for only mediocre results. This cleans completely and no more buying media. You'll learn the hardships though, noisy, messy, have to keep the pins policed up and how to dry your brass effectively. I had to read miles of opinions to glean what I needed. Including why my brass was turning dark again after polishing...
    Regards, Jim

  8. #5
    Contributing Member ssgross's Avatar
    Join Date
    Jan 2020
    Last On
    Yesterday @ 09:16 PM
    Location
    Virginia
    Posts
    1,517
    Local Date
    03-28-2024
    Local Time
    09:03 AM
    Quote Originally Posted by Steve762 View Post
    Pin tumbling seems to be replacing corn cob media tumbling/vibrating since it gives excellent results with no dus
    I pin tumble range brass. My own brass that never hits the floor gets walnut media tumbled for 2-3 reloads, then pin tumbled (no reason other than time/hassle drying...even with a dryer). I use walnut media too for tumbling to de-grease after sizing or assembling. very quick for this.

  9. #6
    Advisory Panel browningautorifle's Avatar
    Join Date
    Jul 2008
    Last On
    Yesterday @ 10:05 PM
    Location
    Victoria BC
    Posts
    29,836
    Real Name
    Jim
    Local Date
    03-28-2024
    Local Time
    06:03 AM
    Quote Originally Posted by Steve762 View Post
    Love pin tumbling. Did not realize how much I detested the dusty mess of corn cob/walnut media. With pins the nasty munitions residue goes down the drain and does not stay around your reloading area as lead/carbon media dust. Pins give better results and clean primer pockets in a few hours. No worries about any case lube or wet media remaining on the inside of the case.
    Agreed on all this...

    Quote Originally Posted by ssgross View Post
    My own brass that never hits the floor gets walnut media tumbled for 2-3 reloads, then pin tumbled (no reason other than time/hassle drying...even with a dryer).
    Yes, a hassle but the end product...

    I spread my brass out on a flat area on a garbage bag and pins too to dry. Works better than the oven or the dryer. Just leave it 24 hours. Most people can't get away with this...
    Regards, Jim

  10. #7
    Legacy Member old tanker's Avatar
    Join Date
    Apr 2017
    Last On
    Yesterday @ 10:13 AM
    Location
    Fort Knox, KY
    Age
    74
    Posts
    347
    Real Name
    Emil
    Local Date
    03-28-2024
    Local Time
    09:03 AM
    I keep a wide mouth plastic jug with a screw top filled with soapy water in the range kit. The brass goes in it as soon as practical after firing. Riding in the back of the truck from some ranges it is pretty well tumbled by the time I hit the highway.

  11. Thank You to old tanker For This Useful Post:


  12. #8
    Contributing Member CINDERS's Avatar
    Join Date
    Nov 2009
    Last On
    03-25-2024 @ 11:01 AM
    Location
    South West Western Australia
    Posts
    7,734
    Real Name
    CINDERS
    Local Date
    03-28-2024
    Local Time
    09:03 PM
    I use distilled water for sonic cleaning after tumbling and also rinsing the cases if you use normal tap water the minerals in it tend to discolour and streak when dried and looks bad.

+ Reply to Thread

Similar Threads

  1. New to Blackpowder Milsurps - Where Do I Start?
    By sledge in forum Black Powder
    Replies: 11
    Last Post: 12-18-2012, 09:42 AM
  2. Blackpowder Pistol...real or reproduction?
    By scdigger in forum Black Powder
    Replies: 2
    Last Post: 08-05-2011, 08:13 PM
  3. 1923 lithgow, to clean or not to clean?
    By BushyFromOz in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 11
    Last Post: 01-06-2011, 06:50 PM
  4. blackpowder measure
    By biggles in forum Black Powder
    Replies: 10
    Last Post: 08-20-2009, 01:38 PM
  5. Lee Metford and blackpowder
    By Patrick Chadwick in forum Black Powder
    Replies: 7
    Last Post: 08-06-2009, 12:56 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Raven Rocks