+ Reply to Thread
Page 2 of 3 FirstFirst 1 2 3 LastLast
Results 11 to 20 of 27

Thread: Lyman Wet Tumbler Leak Solution

Click here to increase the font size Click here to reduce the font size
  1. #11
    Legacy Member Bruce_in_Oz's Avatar
    Join Date
    Jun 2008
    Last On
    Yesterday @ 04:54 AM
    Location
    Brisbane
    Posts
    2,237
    Local Date
    03-29-2024
    Local Time
    05:17 PM
    I used to lay a towel on top of our old electric hot-water heater, which was quite large and stood in its own alcove in my workshop.

    When it started generously leaking onto the floor, we replaced it with an "outside-rated" one of more modest dimensions, so it is back to sun-drying on old towels spread out on the lawn.

    Those Lyman pins are a great polishing aid, but they are expensive and get into odd places in the brass, (not so much with 9mm cases).

    I bought one of those hand-cranked rotary media separators (the cheap blue one) to do a primary separation and "slow spin-dry". This gets most of the pins and water out. The next step is to use a fairly powerful old magnet from an expired loudspeaker driver to sweep up the ones among the dried cases on the towel.

  2. # ADS
    Friends and Sponsors
    Join Date
    October 2006
    Location
    Milsurps.Com
    Posts
    All Threads
    A Collector's View - The SMLE Short Magazine Lee Enfield 1903-1989. It is 300 8.5x11 inch pages with 1,000+ photo’s, most in color, and each book is serial-numbered.  Covering the SMLE from 1903 to the end of production in India in 1989 it looks at how each model differs and manufacturer differences from a collecting point of view along with the major accessories that could be attached to the rifle. For the record this is not a moneymaker, I hope just to break even, eventually, at $80/book plus shipping.  In the USA shipping is $5.00 for media mail.  I will accept PayPal, Zelle, MO and good old checks (and cash if you want to stop by for a tour!).  CLICK BANNER to send me a PM for International pricing and shipping. Manufacturer of various vintage rifle scopes for the 1903 such as our M73G4 (reproduction of the Weaver 330C) and Malcolm 8X Gen II (Unertl reproduction). Several of our scopes are used in the CMP Vintage Sniper competition on top of 1903 rifles. Brian Dick ... BDL Ltd. - Specializing in British and Commonwealth weapons Specializing in premium ammunition and reloading components. Your source for the finest in High Power Competition Gear. Here at T-bones Shipwrighting we specialise in vintage service rifle: re-barrelling, bedding, repairs, modifications and accurizing. We also provide importation services for firearms, parts and weapons, for both private or commercial businesses.
     

  3. #12
    Advisory Panel browningautorifle's Avatar
    Join Date
    Jul 2008
    Last On
    Today @ 12:49 AM
    Location
    Victoria BC
    Posts
    29,839
    Real Name
    Jim
    Local Date
    03-29-2024
    Local Time
    12:17 AM
    Quote Originally Posted by Bruce_in_Oz View Post
    Those Lyman pins are a great polishing aid, but they are expensive
    They're $85CDN for a 5LB bag here. I took the best care of them.

    Quote Originally Posted by Bruce_in_Oz View Post
    I bought one of those hand-cranked rotary media separators
    That's what I got too, they're designed for use with the pins.



    Quote Originally Posted by Bruce_in_Oz View Post
    a fairly powerful old magnet
    I had a handle magnet to go with, it worked better than my eyes to find the pins.
    Regards, Jim

  4. Avoid Ads - Become a Contributing Member - Click HERE
  5. #13
    Contributing Member usabaker's Avatar
    Join Date
    May 2017
    Last On
    Yesterday @ 08:08 PM
    Location
    San Deigo, CA
    Posts
    1,733
    Real Name
    Bill Baker
    Local Date
    03-29-2024
    Local Time
    12:17 AM
    I'm still on the fence about wet tumbling. I don't know if the x3 extra effort to make the cartridges pretty worth it. I get paranoid that pins might unknowingly be inside the cartridge case and find myself checking them during each process of reloading. I always decap my casings first, so even when I dry tumble in my Lyman vibratory the primer pockets get clean enough where it does not effect anything, not that not cleaning them changes anything either,
    Veteran US Navy Seabees - US Army Corps of Engineers - American Legion Post 0867
    " Only two defining forces have offered to die for me. 1.) Jesus Christ 2.) The American G.I. "One died for your soul, the other for your freedom! "

  6. #14
    Advisory Panel browningautorifle's Avatar
    Join Date
    Jul 2008
    Last On
    Today @ 12:49 AM
    Location
    Victoria BC
    Posts
    29,839
    Real Name
    Jim
    Local Date
    03-29-2024
    Local Time
    12:17 AM
    Quote Originally Posted by usabaker View Post
    when I dry tumble in my Lyman vibratory the primer pockets get clean enough
    It's not that they get clean enough, your cases are like new brass after wet tumbling. Yes, more effort but no comparison. I did dry tumbling for 40 years and swore I didn't need wet tumbling but once I tried wet I found the dry had been a waste of time. My Dillon press stayed clean while loading. I didn't have any pins get past the drying phase.
    Regards, Jim

  7. The Following 5 Members Say Thank You to browningautorifle For This Useful Post:


  8. #15
    Contributing Member ssgross's Avatar
    Join Date
    Jan 2020
    Last On
    Yesterday @ 10:09 PM
    Location
    Virginia
    Posts
    1,517
    Local Date
    03-29-2024
    Local Time
    03:17 AM
    Quote Originally Posted by browningautorifleicon View Post
    It's not that they get clean enough, your cases are like new brass after wet tumbling. Yes, more effort but no comparison.
    I think the biggest advantage is how much easier it is to inspect cases for signs of over stretching, and it's easier to see when they are annealed properly. New 30-06 brass has been very hard to come by these last few years, and so I've been tuning my process and shooting to make what I have last a bit longer. I'm on my 12th reload of the current lot. Each case needs carefully inspected at this point, and bright shiny from wet tumbling makes any flaws easier to spot. The first sign 30-06 brass needs to be tossed is a ring 1/3 down the case, clearly visible with just a glance inside the case after wet tumbling. Annealing after each firing and using lower(ish) pressure loads when you can will double the life of 30-06. Just my 2 cents.

  9. The Following 2 Members Say Thank You to ssgross For This Useful Post:


  10. #16
    Legacy Member RAM1ALASKA's Avatar
    Join Date
    Aug 2020
    Last On
    03-27-2024 @ 10:47 AM
    Location
    Southcentral AK
    Posts
    68
    Real Name
    Rob
    Local Date
    03-28-2024
    Local Time
    11:17 PM

    Late to the party!

    Well folks, I may be a little late to the party but better late than never. I solved my leaking gasket problem by just slobbering up the gaskets with dawn dish soap when I'm at the sink loading with water etc.
    A pinch of lemeshine, a blurb of Dawn dish soap and fill with hot water.
    Tumble for an hour or so and then check. Don't want to get too carried away with the wet tumbling or they start to look frosted or maybe take on a satin look......
    I keep an eye on them and when I'm happy the next step is dump dirty water into a bucket, and then move along to an old Dillon hand crank media separator,(garage sale $20), Full of water and tumble for a bit,
    Next is into an old colander for a vigorous shake while blowing with compressed air.
    Then onto a cookie sheet with paper towels,
    And since my reloading is done in the winter time, I just slide the cookie sheet under the woodstove overnight and retrieve the next day.
    Since I have well water, I usually end up with some spotting, so it's off to the dry media tumble for a bit and they come out looking like new.

    I also read somewhere along the way, if you have one of the pick up magnets that's made especially for retrieving the stainless pins,
    Best off not to submerge in the water,, as they trap water inside and then rust from the inside out.
    Hope this helps !
    Edit: may seem like a long process but it's something I enjoy, and I am in no hurry!
    Last edited by RAM1ALASKA; 06-04-2023 at 11:17 AM.

  11. #17
    Advisory Panel browningautorifle's Avatar
    Join Date
    Jul 2008
    Last On
    Today @ 12:49 AM
    Location
    Victoria BC
    Posts
    29,839
    Real Name
    Jim
    Local Date
    03-29-2024
    Local Time
    12:17 AM
    Quote Originally Posted by RAM1ALASKA View Post
    Don't want to get too carried away with the wet tumbling or they start to look frosted or maybe take on a satin look......
    I did mine for three hours without fail, and they never came out frosted. They always had a perfect shine like factory unless I added too much dawn or lemme shine. Then they would come out perfect and turn butter color as they dried.
    Regards, Jim

  12. Thank You to browningautorifle For This Useful Post:


  13. #18
    Contributing Member ssgross's Avatar
    Join Date
    Jan 2020
    Last On
    Yesterday @ 10:09 PM
    Location
    Virginia
    Posts
    1,517
    Local Date
    03-29-2024
    Local Time
    03:17 AM
    Quote Originally Posted by RAM1ALASKA View Post
    Don't want to get too carried away with the wet tumbling or they start to look frosted or maybe take on a satin look
    Too much lemishine (or equivalent polish substance) will make them look dull and cause green spots. I also found that that if I store them after they are dry, I get some tarnish spot. Now if I know I won't get to them for a few days or more, I just go ahead and lube them right out of the dryer. I did start annealing this year too, so they get dried twice, once after tumbling and again after they drop from the annealer into a bucket of water.

  14. Thank You to ssgross For This Useful Post:


  15. #19
    Legacy Member RAM1ALASKA's Avatar
    Join Date
    Aug 2020
    Last On
    03-27-2024 @ 10:47 AM
    Location
    Southcentral AK
    Posts
    68
    Real Name
    Rob
    Local Date
    03-28-2024
    Local Time
    11:17 PM
    Browingautorifle said :
    I did mine for three hours without fail, and they never came out frosted. They always had a perfect shine like factory unless I added too much dawn or lemme shine. Then they would come out perfect and turn butter color as they dried.
    ************************************************** **
    absolutely on the three hours, I don't remember but I have a sneaky suspicion I probably way over did the tumble
    and the additives and I agree on too much of the additives is definitely a recipe for problems.
    At any rate, the satisfaction of seeing a batch turn out "just right" puts a smile on my face !

  16. #20
    Advisory Panel browningautorifle's Avatar
    Join Date
    Jul 2008
    Last On
    Today @ 12:49 AM
    Location
    Victoria BC
    Posts
    29,839
    Real Name
    Jim
    Local Date
    03-29-2024
    Local Time
    12:17 AM
    Quote Originally Posted by RAM1ALASKA View Post
    too much of the additives is definitely a recipe for problems.
    I also wonder about content of the tumbler? I found a tall margarine tub full of brass, no matter what caliber was all I could put in reliably. Any more was too much. I had the big tumbler... I had problems to start and had to read every forum I could to glean the small detail answers and sort out my problems. Good thing I have the time to do the research.
    Regards, Jim

+ Reply to Thread
Page 2 of 3 FirstFirst 1 2 3 LastLast

Similar Threads

  1. Looking for a Lyman 48C
    By t4halo in forum M1903/1903A3/A4 Springfield Rifle
    Replies: 4
    Last Post: 12-05-2016, 06:09 AM
  2. Lyman Jr Targetspot
    By Calfed in forum M1903/1903A3/A4 Springfield Rifle
    Replies: 2
    Last Post: 04-17-2013, 06:36 PM
  3. 1903-A3 with Lyman receiver sight and Lyman 17 front sight...
    By Stillwater in forum M1903/1903A3/A4 Springfield Rifle
    Replies: 4
    Last Post: 07-13-2012, 02:58 AM
  4. NM Lyman 48??
    By xs hedspace in forum M1903/1903A3/A4 Springfield Rifle
    Replies: 4
    Last Post: 10-01-2011, 09:57 PM
  5. Lyman M-Die anyone?
    By M1Tommy in forum Ammunition and Reloading for Old Milsurps
    Replies: 16
    Last Post: 08-04-2009, 10:21 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Raven Rocks