Saw an upper @ a WAC show two years ago, can't remember the manufacturer.
But seems like a doable idea???
Thanks, for responses.
Type: Posts; User: jjroth; Excluded Forums: Milsurp Knowledge Libraries (READ ONLY)
Saw an upper @ a WAC show two years ago, can't remember the manufacturer.
But seems like a doable idea???
Thanks, for responses.
Snow!
have had no desire for either a AK or SKS.
Am satisfied with my Carbine & 1991A1.
Do I need the foreign firearms???
The real question on the Carbine is why it never was considered using...
armed with local weapons to ease supply?
Have seen still photo's of the "Polar Bears" armed with MN.
Try contacting the Michigan Historical library/ museum in Lansing, MI.
Hope this helps.
for substitute standard rifles, e.g.: 1903's & 1917, but high Stadard (HS) made small run of four grooves for 17's (??)
M1's were specified for four-groove only.
Any barrel presented as a M1,...
will cause problems. Should have the "underline M" on outward facing surface.
All mags to have the longest length to the rear of mag body.
IS this with FMJ or soft-nose ammo, may need to...
by Kunhausen.
It has a good section on the how to accurize.
early 1980's, had an article about the semi's based on the M14 action.
These were made at the Springfield Armory, without the leg for the full auto parts and
dismounted the OP-rod using the M1...
What deer being hunted?
Something here on the Sound side or east?
And something try for Elk??
How big is the grand son?
Maybe a bolt action using a 7-08 or 270? get a youth stock then...
Tango Yankee!
Suggest a little "Scott's Liquid Gold" on rag and over the stock, looks like it needs a little freshening.
you get some clean stuff latch on to it. LC69 seem better.
what to know about it?
How different from the service variant used the Canadian forces in WWI?
"gussied up" by a former owner.
Remington-Rands were a staple of WWII, not real exceptional.
Only significance would be if the SN was traced to a well known figure???
Strip it and look...
in Gettysburg, Pa.
They'll should be able to indicate what's current.
very nice for age!
was 3% Nickle, Remington & Eddystone were carbon steel???
((FACT CHECK, aisle 13!))
for IDing old powder.
Best bet would be to load with new powder, one kaboom might ruin you day, appearance, firearm, etc
and an extremely abrasive residue is left.
Are your group holding tight???
and weld to it a 6" long piece of 5/8"W X 3/15 CRS to it.
THen use a Weaver 336 scope mount to locate the holes for drilling & tapping a Scout scope mount.
Did this to mine when the youngest...
that on a grizzly there 5% area to hit with firearm to put it down, hit the other 95% and you see what a sense of humor they have!
I think that its a follow-up to the FS servey where the indicate...
these seems to be an interesting rifle, too bad it not the 8mm Mauser round.
Are stripper still available?
As the rounds and the clip are insertted together and after final round the clip drops...
Are these bored-thru for a sub-caliber? or solid?
Looks likw some use on them.
Interesting.
rifle that was converted to cock on opening not theon closing as normal.
Try a 10" loop of nylon cord, hold rifle muzzle down, and catch bottom of loop, on the underside of bolt knob and pull...
any type of gunsmithing?
Have a "Type 56 Chicom" bolt action carbine, that needs a new barrel and stock. [1960 stamp above chamber on barrel]
Inland with stock pouch and two 15 with 12 each of the Win 110HP.
Did a slight polishing job on feed ramp to minimize stuttering of soft-nose ammo.
National Ordance M1 Carbine, majority are GI parts??
Local pawnshop has one for $550.