-
Contributing Member
Ecuador 88 Commission Rifle Carbine Conversion
-
The Following 6 Members Say Thank You to Aragorn243 For This Useful Post:
-
05-28-2017 08:05 AM
# ADS
Friends and Sponsors
-
Legacy Member
Yep she's a bit rough. I'm sure by the time you are finished it will be beautiful and we will all be wondering how we didn't see it's potential.
-
-
-
Advisory Panel
Yup, pretty rough. I know you already know how it's going to turn out though, after the last one...
-
-
Legacy Member
Neat little carbine. Looks like it is a good time for Commission Rifles at the moment, I have two M13s on the way (don't worry there will be photos and details).
Just a small point for the ammo. The 'S' marking on a Commission 88 doesn't mean it is safe to shoot .323 bullets. Most 'S' marked barrels actually have the original barrel still (which generally measures .3215). My personal loading for Commission rifles of all sorts is a 170grn .321 bullet (i.e. 32 Winchester Special bullet), under 40grns of IMR 3031. Haven't done much testing with the accuracy yet, but it has shown plenty of potential and I intend to have that same load out shooting today (this time for a 88/05).
I highly recommend slugging your bore before shooting any Commission 88 rifle, it can provide very useful knowledge as to what type of bullet to use. Remember some even have a .316 bore (Czech
barrel) and I definitely wouldn't want to send a .323 bullet down that!
-
Thank You to Eaglelord17 For This Useful Post:
-
Legacy Member
Lots of incorrect information posted here . First the German military NEVER sold any Gew-88's in the 1900's , that is bad information put out by someone who made a some mistaken conclusions based on bad information . The Gew-88 was Germany
's most numerous and main battle rifle until 1911 . Other than some commercial sales from Steyr of 1894 dated rifles , the 88's went to SA from the Czechs in the late 20's and early 30's . There are NO S marked barrels , only the receiver . So if the barrels was changed , the S on the receiver means nothing . The Gew-88 was never meant to fire a .323 dia bullet , ever . The Bullet in the S ammo was .321 dia and designed to be fired in the Gew-88 with it's .321 bore . The S is not a bore size . The Z marking IS a bore size , .323 , but it was still for the .321 dia bullet . The SA rifles will be found with more original .321 German barrels than the extra small .3165 Czech
barrels . Yes the .321 dia Win special bullet is a good one to use in .321 88's . I put out that info over 20 years ago , when everybody was just sure the rifles all had .318 bores [ which they NEVER used ] .
-
The Following 2 Members Say Thank You to bob q For This Useful Post:
-
Contributing Member
This one is worse than the Belgian so a bigger challenge. Not in a hurry to shoot it.
-
Thank You to Aragorn243 For This Useful Post:
-
-
The Following 2 Members Say Thank You to Aragorn243 For This Useful Post:
-
Contributing Member
Great news. I got it apart. Photos probably tomorrow on interior and the state of the barrel shroud. There were three casualties, one fatal. The screw in the nose cap would not move, screwdriver, vise grips, etc so drilled it out. In the process the nose cap suffered some minor damage. The stock has some dry rot and the end cap area was very weak, a third of it had already rotted away and when I pulled the barrel out, it snapped off. Barrel shroud was indeed cut under the barrel band. It looks like they installed a smaller tube inside the two sections. Not sure how it is held together, rust may be hiding spot welds. The rust underneath is pretty bad on the shroud but doesn't appear to have gone through or weakened it significantly. I did not try taking the shroud off. Will wait until after electrolysis to attempt that. There is actually a 1 inch square of good bluing under there. The rest is orange. Receiver is pretty good, only one small area of significant pitting that I saw. Didn't mess with it much it was covered with liquid wrench and I was doing my best to not get filthy. Wife says I failed anyway.
Tomorrow I'm going to set up my electrolysis bath and get it cooking.
-
Thank You to Aragorn243 For This Useful Post:
-
Legacy Member
-
-
Contributing Member
Sorry Bob, sticking with Paul. He has documentation, you don't.
-