-
Contributing Member
Advice on where I can get Garand Cheek Pad
Veteran US Navy Seabees - US Army Corps of Engineers - American Legion Post 0867
" Only two defining forces have offered to die for me. 1.) Jesus Christ 2.) The American G.I. "One died for your soul, the other for your freedom! "
-
-
09-11-2020 12:04 PM
# ADS
Friends and Sponsors
-
Advisory Panel
Well, where did you get the ugly one? IMA shows them https://www.ima-usa.com/products/u-s...d-medium-brown
Joe Salter has an original that would come up with oil Original Garand M1-D Cheek Piece
Ebay has a plethora... m1 garand cheek pad | eBay
-
-
-
Contributing Member
Ebay has a plethora... m1 garand cheek pad | eBay
I have learned, the hard way, when it comes to these on eBAY what they say and show when it arrives is nothing like the original or even a good reproduction. I've ordered twice and both times have got some cheap article and wasted $30.00 on each, Which is why I posted the question here hoping for a reliable source.
At this point, I might be better off just spending the time to make my own reproduction.
Veteran US Navy Seabees - US Army Corps of Engineers - American Legion Post 0867
" Only two defining forces have offered to die for me. 1.) Jesus Christ 2.) The American G.I. "One died for your soul, the other for your freedom! "
-
-
Advisory Panel
Too bad I didn't keep some we had here. Our storesie ordered in some "Cheek rests" he found in the fisch years gone by(about 1990) and thought they might be for the new C7 (M16A2). He showed me one of the dozen or so he had just received and they were original in the wrap cheek rests like you seek. Probably a hold over from M14s though. NEW! I didn't even take one and have no idea what happened to them.
Yes, Ebay can be a dick to work from.
-
Thank You to browningautorifle For This Useful Post:
-
Legacy Member
usabaker
Try here Cheekpiece, Sniper w/ Leather Lace & 2 Brass Mounting Screws | Gun Parts. It's a reproduction but I have fairly good luck with Numrich.
BEAR
-
-
Contributing Member
Originally Posted by
BEAR
It's a reproduction
Bear, Thanks... That looks almost exactly like the last two I bought that didn't cut the cake. Have you bought one from them?
This is what I have been getting,
Attachment 111004
Veteran US Navy Seabees - US Army Corps of Engineers - American Legion Post 0867
" Only two defining forces have offered to die for me. 1.) Jesus Christ 2.) The American G.I. "One died for your soul, the other for your freedom! "
-
-
Advisory Panel
Left one might have been OK if it had horsehair filler.
-
-
Legacy Member
[QUOTE=usabaker;483148]Bear, Thanks... That looks almost exactly like the last two I bought that didn't cut the cake. Have you bought one from them?
Not a cheek pad but other stuff. I don't need a cheek pad for an M1.
I almost purchased one for an M1A
some years ago but when I was active duty I attended a "Reconnaissance and Target Interdiction Course" in the early 80s. We had to make our own cheek pad for our M21s. They consisted of military grade Kotex pads taped to the rifle but with green "100mph" tape. We asked about the M1 cheek pad but the instructors said that the pads were constructed for the offset scope that was used on the M1 and would not work on the M21.
Later I purchased a leather cheek pad from Cabela's and it works great with or without a scope.
Attachment 111005
Last edited by BEAR; 09-15-2020 at 01:28 PM.
-
Thank You to BEAR For This Useful Post:
-
Contributing Member
Left one might have been OK if it had horsehair filler.
just that cheep form and it doesn't fill up the cavity at all
Veteran US Navy Seabees - US Army Corps of Engineers - American Legion Post 0867
" Only two defining forces have offered to die for me. 1.) Jesus Christ 2.) The American G.I. "One died for your soul, the other for your freedom! "
-
Thank You to usabaker For This Useful Post:
-
Advisory Panel
I know it wasn't what you asked Bill...but if you got hold of those felt insoles for boots you could cut the correct form to fit the shape. It's the same sort of filler you find in the issue...I think they were two layers for those of us with prominent cheeks, so we could remove one layer. I speak hopeful of the one on left you showed, light tan and close to spec?
-
Information
PM
