-
Legacy Member
New To Me, My First M1 Carbine, Inland 5.35
Here’s a new to me M1
. I’m very happy with it as it’s my first. So it will always be special to me. I’d love to hear everyone’s thoughts on it.
https://photos.app.goo.gl/GZUGsjXCR6MvsLi76
Front Sight: Quality Hardware JQ Type I
Barrel Band: Type III MMQ Post-War
Barrel: Inland 7/44
Receiver: Inland 5.3
Rear Sight: IR Co. w/PN Type III Late War/Post War Adjustable
Recoil Plate: Inland Type III
Stock: Early Underwood Type II M-U
Buttplate: Underwood
Handguard: Underwood Type II M-U
Trigger Housing: Saginaw Type III
Trigger: Saginaw Type Type II
Sear: RIA Type III
Hammer: Saginaw Type III
Safety: CM Type IV
Magazine Catch: Unmarked Type IV
Plunger Asmbly: Type I
Mag Spr/Plunger: Unmarked
Bolt: Underwood Type II Flat
Firing Pin: Underwood Type II
Extractor: Underwood Type III
Slide: Saginaw III
Information
|
Warning: This is a relatively older thread This discussion is older than 360 days. Some information contained in it may no longer be current. |
|
-
Thank You to WinterRanger For This Useful Post:
-
05-13-2021 02:25 PM
# ADS
Friends and Sponsors
-
Legacy Member
Nice piece of hardware. I would have someone check it out if you are not familiar with the carbine. Nit picking...the stock is too shiny. Rub it down with fine steel wool to take some of gloss off. You will shooting it. Enjoy.
-
-
-
Contributing Member
Very nice! Looks like a full factory refurb to the Type 3 package (sight, front barrel band, flip safety and refurb stamp on the left side of the stock). I just picked up a Standard Pro (my 3rd M1
, just have 6 more to go!) just like it. My question to the experts on this forum is did these factory refurbs usually use such a variety of parts from different manufacturers? Congrats on your first one!
-
-
Yea, It looks like a Marlin made stock, thick wristed. 3 holes under butt plate ?
Near the CC, Can you make out the Boxed GHD / UEF ? Seems like I can see part of it..... Or think I can.
Also appears the stock has been oiled recently. Does it still have a sticky feel ?
Where the Hi-Wood was cut down... Is it hard to tell by look and feel ? Or easy to tell ?
I ask because it seems RIA cut downs were nicely done, when compared to other Arsenals... from what I've seen. And the notch meets the hand guard notch nicely.
Looks nice, barrel gauge out pretty good ?
Let us know how it shoots.
Congrats on your 1st and Thx for sharing it
Charlie-Painter777
A Country Has No Greater Responsibility Than To Care For Those Who Served...
-
-
Legacy Member

Originally Posted by
Rockandroll
Nice piece of hardware. I would have someone check it out if you are not familiar with the carbine. Nit picking...the stock is too shiny. Rub it down with fine steel wool to take some of gloss off. You will shooting it. Enjoy.
Yup. Used a little raw linseed oil
on it. I’ll hit it with the 0000 SW. Plan to shoot it.
---------- Post added at 06:16 PM ---------- Previous post was at 06:13 PM ----------

Originally Posted by
painter777
Yea, It looks like a Marlin made stock, thick wristed. 3 holes under butt plate ?
Near the CC, Can you make out the Boxed GHD / UEF ? Seems like I can see part of it..... Or think I can.
Also appears the stock has been oiled recently. Does it still have a sticky feel ?
Where the Hi-Wood was cut down... Is it hard to tell by look and feel ? Or easy to tell ?
I ask because it seems RIA cut downs were nicely done, when compared to other Arsenals... from what I've seen. And the notch meets the hand guard notch nicely.
Looks nice, barrel gauge out pretty good ?
Let us know how it shoots.
Congrats on your 1st and Thx for sharing it

Three holes under Buttplate. Boxed GHD / UEF. If you look at a closeup of the wood you can see how it was unevenly cut to a low wood. I didn’t know Arsenals cut wood down as part of the repro. I’ll add shots of the knife marks in the stock. I assumed it was a soldier.
-
-
Contributing Member
That RLO will really make the wood grain expand and smooth out. It is going to look really great when it gets done!
-
-
Legacy Member

Originally Posted by
Singer B
That RLO will really make the wood grain expand and smooth out. It is going to look really great when it gets done!
I used cold pressed RLO too.
-
-

Originally Posted by
WinterRanger
I used cold pressed RLO too
I wouldn't Steel Wool it. Give it time to dry/soak in. The shine will die down.
When I have stocks needing Oiling,
I dunk my stocks and Hg's in a tank with the RLO lightly thinned and warmed up.
Then on to a Drying/dripping rack that catches the run off.
Hour or so later I buff off any excess from the crevices.
Another hour or two later I double check for any more run outs.
Can be surprising how much some of them swell up.
New life !
Charlie-Painter777
A Country Has No Greater Responsibility Than To Care For Those Who Served...
-
-
Legacy Member
If you really really want to remove any "shine" use bronze wool rather than steel wool. It doesn't rust and stain the wood. and make sure you wipe the stock afterwards with a tack cloth to remove any particles that might stick to or otherwise embed themselves into the wood.
When they tell you to behave, they always forget to specify whether to behave well or badly!

-