Forum: Gunsmithing for Old Milsurps

We have done the best we can to gather together volumes of Machinery’s Reference Series from the early 1900's. So far, we have located the PDF...

Heating Parts Without Getting Burned With today's hot tip is Ken Brooks. Ken shows you how to properly heat parts without destroying the heat...

Part 1 - Field Demonstration of what happens when your firearm has too much headspace. Ken Brooks and Bob Dunlap risk life and limb to take you to...

Parts Cleaning and Organizing Spare Parts First Ken covers cleaning parts and then follows up with tip on how to keep your spare parts organized. ...

Headspace, Part 1: What is it? How is it measured? In this lesson on headspace, Bob Dunlap discusses what it is, why it's important and shows you how...

How to organize your Vertical Mill along with Tips & Projects to get more out of your Milling Machine. Master Riflesmith Darrell Holland shows you...

Bob Dunlap teaches you about slide-under and snap-over extractors in this lesson. <iframe...

Have a spring that's too stiff and needs to be lightened up? Join Ken Brooks as he shares the tips and techniques of lightening coil spring and avoid...

Is your barrel ready to rattle right out of your gun? In this lesson Bob Dunlap and Ken Brooks explain loose breech, then show you how to check for...

Repairing Loose Revolver Grips Tired of shooting your revolver and having it jump all over the place because the grips are loose? In this lesson...

This post is a tutorial on some of the things you can do to maximize the inexpensive chinese import 7" swing lathes to turn the machines from barely...

Checking for proper Muzzle Brake Installation Not sure if your muzzle brake is affecting your accuracy? Ken Brooks shows you how to check whether...

Screeeech..... Aw Crap!! That's going to leave a mark!! Today Ken Brooks shows how non-marring tools can save you from embarrassment (and from a...

Today Ken Brooks shows you a specialized spring tool he made and tells you how use it and how to make one yourself. As a bonus, Ken also talks about...

In this lesson, Ken Brooks talks about why triggers are heavy and hard to pull from the factory and how to responsibly perform a trigger job. ...

As you learned in the last lesson on Extractors, "Moment of Mass" can cause problems with your gun. In this lesson Bob Dunlap describes some of the...

Is your workshop a mess? Join Darrell Holland as he shows you time saving tips on how to organize your space. <iframe...

What to look for in a Bench Vise & their care. In this lesson Ken Brooks discusses the proper care and feeding of the bench vise and shares his...

Just follow these tips from Ken Brooks on organizing your workbench and become more efficient. <iframe...

In this mini-lesson, Professional Gunsmith Ken Brooks discusses specialized screwdrivers for Gunsmithing and shows you how to modify an existing...

Today AGI president Gene Kelly takes you through various jaw attachments that allow your vise to grip a part without leaving marks on it. <iframe...

Are you an accuracy nut? Then you'll want to hear what Ken Brooks has to say in today's lesson on bedding rifles. <iframe...

In a new series of lessons, Bob Dunlap takes up firing pin design and fit. As always Bob tells you the WHY not just the HOW. In this lesson he...

Want the maximum accuracy and performance from your rifle? Darrell Holland gives you detailed instruction of properly cleaning your rifle so you can...

In today's lesson Ken Brooks shows you how using tweezers, forceps and specialized pliers can make your life easier and follows up with tips on...

Are you getting rectangular holes instead of round holes in your target when at the range? Then this lesson on bullet stability and yaw, featuring...

Today, Ken Brooks discusses how to properly care for your files so you can get the most out of them. As a bonus, Ken also discusses many of the...

What kind of Gun Oil Should You Use? Lubricants/Penetrants/Protectants. Join Ken Brooks as he discusses various lubricants, penetrants and...

Your FINAL Extractor Lesson - Did You Pass? Your extractor is shaped and fitted well and has proper spring tension, yet you still have feeding...

How to see in the dark - Gunsmithing Inspection Lights Are you in the dark about firearm inspection lights? Join Ken Brooks as he demonstrates...

Foredom Tool Tips Organizing Your Foredom/Dremel Tool Bits. In today's lesson Ken Brooks shows how easy it is to keep tool bits organized and how...

Does the Left Hand (Extractor) Know what the Right Hand is Doing?! The Left Hand Extractor. Extractors come in both left and right hand...

How to Set Up Your Welding & Heat Treat Areas Need to weld or heat treat parts and don't want to get burned? Ken Brooks shows you how to properly...

Glues & Epoxies for Gunsmithing In this lesson, Ken Brooks talks about glues and epoxies, including how to color match adhesives to the material...

Test Firing After Making a Repair - "How & Why" You just finished a repair, now it's time to go to the range and test it! In this issue, Ken...

Do you know what to Look For when Buying a used Remington 700? Don't want to get burned? Master Riflesmith Darrell Holland takes you in-depth into...

How to fit an Extractor - Shaping and Contouring the Hook Have a gun with problems feeding or extracting? The shape of the extractor hook could...

How much spring tension does an extractor need to do it's job? You might be surprised!! In this lesson Bob Dunlap takes up the subject of spring...

Tapered vs Hollow Ground Screwdrivers? A screwdriver is a screwdriver, right? Not necessarily! Join us as Ken Brooks shows us the differences...

Spent the money to buy a newer rifle from Savage and now you want to get the most out of it? Darrell Holland's lesson on the ins and outs of the...

Part 1 - In this Classroom segment AGI Master Gunsmithing Instructor Bob Dunlap introduces you to the purpose and concepts of extractors and explains...

In this mini lesson, Master Riflesmith Darrell Holland shares a wealth of information about working on Remington 700 rifles that will improve...

Don't throw away that broken or worn out punch! Master Gunsmith Ken Brooks shows you how to breath new life into that old punch! <iframe...