-
Legacy Member
Last edited by Jim; 05-19-2010 at 12:23 AM.
-
-
05-19-2010 12:14 AM
# ADS
Friends and Sponsors
-
Legacy Member
"ax" coded rifles are kind of hard to come by. more so for ax 41's. and yes, it's from Feinmechanischewerke Erfurt. they would later change their name to Erfurter Maschinenfabrik, or "Erma" for short. nice pick up
-
-
-
FREE MEMBER
NO Posting or PM's Allowed
Nice ax 41. I have one too (also a Russian capture). What a great gun. The finish is starting to peal on the handguard. I'm considering refinishing it to a more original look versus the dark Russian shellac. It's pretty accurate. From what I've heard, the ax 41's are pretty rare. Great find once again
-
Legacy Member
Thanks! I always wanted one of these because I really like the old fashioned script on the "MOD."98. So I was tickled when this one showed up at the local gun shop. I had no idea it was at all rare too.
Concerning the finish, its shellac was pretty rough so I decided to go ahead and and refinish it in oil. I know there's two schools of thought on the finish in these. But I decided to do it as I did since its never very likely to gain more value as one version over the other and it looks best this way since the shellac finish was so far gone.
If you're interested in preserving your shellac finish, it's not that hard. Shellac finishes are easy to repair since it dissolves and blends with any new coats, unlike oil. Remove any loose or flaking shellac with coarse steel wool. Brush or spray on some fresh shellac over any bare spots. Let that dry about 24 hours and buff any area divisions with steel wool and then recoat entirely. You can brush it on or spray. If you need color, you can add any alcohol based tint to the shellac to match your rifle.
Last edited by Jim; 07-12-2010 at 01:19 PM.
-
Thank You to Jim For This Useful Post:
-
FREE MEMBER
NO Posting or PM's Allowed
Your welcome The only reason I may refinish mine is to give it a more German look. I am going to get started in reeenacting so I need a mauser with the original issued look. Do you have an idea on what kind of finish I should use if I do decide to refinish the rifle? My shellac is pretty worn and I'm pretty sure the Germans didn't even use shellac on their rifles so I don't necessarily want to keep a similar finish to what it currently has. So that being said, does anyone have an idea on what is the best finish to put on the gun to give it the german issued look?
-
Contributing Member
I just used BLO on mine and it came out pretty nice. Photos on page 2 of this thread:
Russian Capture k98
-
-
FREE MEMBER
NO Posting or PM's Allowed
Thanks Aragorn243! What about using a lacquer thinner on the existing finish and then using birchwood casey's tru oil on the stock? If you check out iraqveteran's video on youtube on gun stock refinishing, his end result is really nice. I think it's video part 4. IMHO it looks pretty good. I've made up my mind and either way, I'm refinishing the stock tomorrow. I think I'll put up a thread on the project start to finish so that you all can enjoy it. Wish me luck as this will be my first stock refinish. I've done my research though so if I follow directions, it'll end up fine. Thanks again you guys for all the help
-
Legacy Member
-
Thank You to Jim For This Useful Post:
-
FREE MEMBER
NO Posting or PM's Allowed
I did refinish the stock with tru oil and it really gave it a good look and I used steel wool to knock the shine down to a dull finish. Now it looks really good and I uncovered three swastikas on the right side of the stock that you couldn't see before with the crappy flaking shellac. They're very lightly pressed into the wood but hey...it's better than nothing and you can actually see them with the new finish on. The finish is a lot darker than you normally see on a k98, but the wood was really dark when I stripped it so I guess that could be why the end result is darker than normal. Thanks for the advice though guys. If I ever have to refinish another mauser k98, I'll try your method Jim. Thanks again