first carbine unboxing

[jond41403]

Wasn't really meant as a sweeping generality, the friend I am referring to is a 75-year-old veteran that has reloaded all his adult life, and he accidentally double charged a case and blew up his Colt Python. That mistake almost made him quit reloading all together because he says he has always been extremely careful and has always had the same routine all his life when reloading. He sits in a room by himself, no one is allowed to knock on the door or even speak to him during the hour he sets aside each day to reload. He has no tvs, no radios in the room, nothing to distract him and he still managed to double charge a case. All I am saying is the absolute truth, every one of my reloading buddies has had at least one accident if not a couple throughout their reloading careers. And of course the same thing can happen with factory ammo as well, it just seems a lot less likely factory-wise which is why I am more comfortable going that route. I'm not exaggerating when I say I shoot at least 6 to 7,000 rounds every year of various calibers, can you imagine how long that would take me to reload that many every year? I would be spending way more time loading than shooting which is the exact opposite of my goal in life ha ha. I have nothing at All against reloaders, most of my shooting buddies are exactly that ��

[floydthecat]

I won’t even use progressive equipment. One at a time by the numbers and powder loaded with specific dippers or measured. I want to see and feel every step….nothing automatic especially powder dispensing and bullet seating.

[jond41403]

Also I have never had any reason to be fearful of a squib, they are audible and literally tell you they are there. I have never had one happen to me personally, but had it happen to a shooter at the table next to me years ago. As long as you have decent hearing, squibs tell you they're there

[DaveHH]

If a person is looking for a reloading error, it will probably happen with a progressive loader. I have a MEC Grabber which is a shotgun progressive, but that is a 5 pull deal and it is right there in your face and requires action each pull. But 25 shells in about 10 minutes is too good to pass up. A high capacity Dillon can have problems that you'll never see.

Electronic scales can cause accidents. I use an RCBS 10/10 which is the best old Ohaus. I also use the old RCBS powder dump which is also the big Ohaus. These are fool proof tools. I switched to a hand held single priming tool as you get to feel that primer seat and inspect each case after use. High primers cause most problems with reloads.

JonD: If you use that much ammunition, reloading is not the way to go. You just have to buy in bulk when you get the best deals, you are not screwing around with Midway or Walmart for your shooting supplies.
D

[jond41403]

Correct, buying in bulk(cases) is the only way if you're using factory and I have been doing that for almost the last 15-20 years. All the brass ammunition I am shooting today, I probably bought more than 10 years ago when it was still fairly priced. The only ammunition I'm having to currently buy every now and then is steel cased ammo for my Russian guns because I go through untold amounts of those. Ammunition and tannerite I am probably good on for the next 10 years or so if I were never to buy another bullet starting today. The only downside to it is storing it within living space in the house. I have a whole spare bedroom devoted to it and I was just telling Charlie last month that I am going to have to have a structural engineer to come look at my floor to make sure the weight can be adequately supported without warping or ruining my floor.

[tenOC]

If you're on a slab, it's a problem. But on crawl or basement you can just shore it up from underneath.
Guys that would store complete engines in garages or drive in basement garages have reported having sunken concrete where several engines are sitting.

[ssgross]

Thanks for everyone's comments. Here we are all cleaned up
Attachment 118223Attachment 118224
With all the dirt and oil lifted off the surface of the wood, I can now make out the cross cannons. I used lacquer thinner and rag. This moves the color around and fixes any "new" scratches or dings etc. Acetone works good too, especially on areas with heavy oil deposits, but it's more aggressive. Laquer thinner is more forgiving on the original oxidized color, in my experience.

I won't get the range until mid next week, but will post back targets of how it ran.

[painter777]

Has anyone been noticing most of the Midway carbines with Dogleg hammers have the 26 Coil Hammer spring ?

Note about reloading:
Check your Powder makers Web Sites Often... multiple times a day.
A number of Powder makers have been selling directly to us the consumer. Price runs about ~$3-$4 more a pound than Honest suppliers sell for.
They do have some limitations: Product must be in stock, 1 order per 30 days, limit of 5 SKU part numbers per item... IE 5-1lb 296, 5-1lb H335 etc until you hit 5 SKU Part numbers, usually 40lb limit on total order (shipping weight), and these are not to be retail sold. My last 3 orders over the past 90+ days have totaled 80+ lbs of Powder.

Don't underestimate Vihtavuori N110 for the M1 Carbine. Little more expensive but very clean and consistent. Shoots very well in cold and hot summer days.

A recent surprise to me: Chrono test achieved quicker speeds from Standard Small Rifle Primers vs Magnum Small Rifle Primers. Standard SRP measured about 30' Fps faster from the muzzle. Will test 296 vs H110 with Stan-SRP vs Mag-SRP soon. And will test the mixed .357 loads of VV110 Soon.

From VV LOAD DATA:
Speer 110 Grn FMJRN
Start 12.1 = 1786 Fps................... Max 14.0 = 1983 Fps

[W5USMC]

Has anyone been noticing most of the Midway carbines with Dogleg hammers have the 26 Coil Hammer spring ?

Not sure I would say most Charlie, I have counted quite a few 22 coil springs on these from the pictures posted. The Winchester I got has a 22 coil spring.

[painter777]

More like a overstatement from me Wayne,
I obviously haven't seen all of them, but from the ones I have seen most had the 26 coil spring.
Like this one here and many by new 1st time owners on Redditt sub forums.

Cheers,