What would it mean if my stock didn't have arsenal rebuild stamps on it?

[shadycon]

Looks like a very nice stock. As stated production run for Std Pro.Type one;I cut highwood.
Type two; oval cut highwood. type three; same oval cut, low wood. As stated most type two have been cut to low wood configuration. Depending on where modifications and upgrades are done depends on who marked them or if marked at all. Or all external markes on stock have been sanded off . I hope this helps. And I hope you get them preforming as they should.GK

Information

Warning: This is a relatively older thread This discussion is older than 360 days. Some information contained in it may no longer be current.

[firstflabn]

98% of your questions would be immediately answered by Riesch's book.

[ChipS]

98% of your questions would be immediately answered by Riesch's book.

ABPOS:

Welcome to the Forum. You apparently are very interested in M1 Carbines. Like the man inferred earlier, you NEED to buy 'U.S M1 Carbines, Wartime Production', 7th Edition, by Craig Riesch. You can get it on Amazon for about $20 delivered (recently, I think) and it will be the best $20 you will ever spend on this affliction. There are books considered by the fans to be better and there are books considered to be worse, but I think Riesch is the handiest, easiest and clearest to understand and use, with minimal arguable errors. It may not give you the detail of some more expensive books but you don't have to read it three or four times to figure out what he is saying. Almost every question you have asked is answered by Riesch in language even a novice can understand. Buy it, love it, live it. And start saving up for 'War Baby', LOL. Semper Fi.

[mjanway]

Like the man inferred earlier, you NEED to buy 'U.S M1 Carbines, Wartime Production', 7th Edition, by Craig Riesch. You can get it on Amazon for about $20 delivered (recently, I think) and it will be the best $20 you will ever spend on this affliction.

I didn't realize the 7th Edition was out, Thanks. Just ordered it.

[USGI]

I didn't realize the 7th Edition was out, Thanks. Just ordered it.

The 6th edition had a table at the back showing 18 changes that were made from the 5th edition. Let us know how many changes this new edition has when you get it. - Bob

[mjanway]

The 6th edition had a table at the back showing 18 changes that were made from the 5th edition. Let us know how many changes this new edition has when you get it. - Bob

I was very curious about that myself. My 6th Edition was looking pretty worn and was accumulating quite a few handwritten notes and corrections so it was good timing. It would be nice if there was a War Baby III out in time for the holidays.

[ABPOS]

Don't have that one. I am reading Canfield's right now though. But it takes time......... I apologize if I shouldn't have asked.

[Bruce McAskill]

Type 1 stocks have an I cut slot for the oiler and high wood stock. Type 2 stocks have what's called an oval oiler slot and has high wood stock. The type 3 is the same as a type 2, but has low wood cut stock. Type 1 and 2 stocks were converted into type 3 stocks by cutting the high wood from beside the slide on the stock. Your stock is one of these.

[ABPOS]

Type 1 stocks have an I cut slot for the oiler and high wood stock. Type 2 stocks have what's called an oval oiler slot and has high wood stock. The type 3 is the same as a type 2, but has low wood cut stock. Type 1 and 2 stocks were converted into type 3 stocks by cutting the high wood from beside the slide on the stock. Your stock is one of these.

I'm lost now. Because it's been said that type II and type III both have oval oiler hole. Mine doesn't "appear" to have been changed to low wood by looking at it. Meaning I don't see any marks that would indicate such. Although if they sanded it well, you might not see it. Maybe that's why you're saying it's an altered type II. Lack of any markings means they might've sanded it? That would make sense now. Because when I look at where the recess is for the "low wood" portion, it looks like it goes fluidly the whole way down back to the receiver. I guess I could put a pic up to show. But the sanding part would make sense. Lack of crossed cannons and what not.

[Bubba-7]

Your stock is either type 2 or 3. I think type 3. But the picture is dark. SP Ordnance stasmp is small and when you learn where to look, you may be able to see part of it. There is a lot to learn with carbines.