-
Legacy Member
№ 32 / № 42 - Scope Graticule Replacement
-
-
08-11-2019 07:17 AM
# ADS
Friends and Sponsors
-
Legacy Member
I decided to have a go at disassembly, i have tried to unscrew the brass front shade a few times before but it wont budge a mm.
The screw on the front shade came undone like it was dont up a couple of days ago.
I could see the threads had been sealed with like a grey putty. It was soft and could be scraped away easily with a wooden tooth pick but the thread was still solid.
I decided to heat the front shade gently with a hairdryer, still it wouldnt come undone as i couldnt grip it good enough. I wrapped masking tape around the brass shade to aid grip, put on my leather palmed cycling gloves and kept the scope in the mount to hold the tube. Heated it again and the grip was so good i could unscrew it easily. Success!
Next was removing the lenses, under a hidden pocket of more putty i could see a tiny screw head. I cleaned it out and it once again un screwed like it had just been done up!
I had to apply a small bit of heat after that and the lense slid right out.
At this point i could now see the graticule inside, once again i located another hidden tiny screw covered with putty. A quick dig with a wooden tooth pick and its accessible. Again undid very easy, and that was it. The graticule tube slid out like a treat.
Well its absolutely nothing like the № 32 diaphragm wise, obviously this scope has no adjustment so its a fixed tube with wires soldered in place.
All i have to do is fit a new graticule, easier said than done!
I studied it hard to figure out how they mounted it square and the wires perpendicular to each other.
Very clever, they have machined a very small Vee slot so the wire drops into the Vee essentially self locating on the centre line. Then soldered in place.
To achieve what i would like, i need to get another vee slot machined perfectly square to the verticle slot. Fit wires, job done! Cough!! 🤣
Would anybody like to help with machining these for me, any help much appreciated.
All i need is the machining work done and im happy to do the wires...
Attachment 102217Attachment 102216Attachment 102218
-
-
-
Legacy Member
Anybody have any wire or know where to find sum?
Thanks
-
-
Save yourself a whole lot of bother and get a No 42 or 53 with what looks like a horizontal AND vertical crosswire. These are actually etched onto a glass plate (which changes the nomenclature from a graticle to a reticle). You then have an already (reasonably) accurately collimated centre-dot/spot to aim with instead of the vertical line which was OK when using it to aim the BESA gun on the Mk7 Churchill but, alas, not a good way to hit targets with a rifle.
The BAD thing about trying to convert your existing No42 inner sleeve (the long brass bit that holds the wire) is that to fix a NEW wire and post, you have to heat up the whole thing to the melting point of solder before it will take. If you insist on converting the glass reticle to cross-wire and post, you can kick out the plate and fit the new wire and post. And you only have a simple 1/16" thick plate to heat up
PS, the reticle plate is held in with screws. Easy to undo, work on and replace.
-
Thank You to Peter Laidler For This Useful Post:
-
Legacy Member
Thanks for the info Peter.
I should have clarified im looking to use this scope more as a prop than a scope i will be shooting with. Perfect post and wire centering is not essential for this project. I have a 1943 Long Branch and would like to be able to sit this Canadian 1943 scope on top of it.
Realistically if i can get the vee machined then mounting the wire should be pretty straight forward.
I have engineering knowledge and im handy at fine work through an eye glass.
At work we have sum amazing loctite adhesive for metals and was going to glue rather than solder. I know, i know... glue sounds terrible but trust me the glues these days are amazing and will be almost as strong as solder.
I have my heart set on this scope also for the amazing condition its in. Its one of the best i have seen, and 42 prices seem to be creeping up. I was lucky, this cost me £50!
Last edited by Scout Sniper; 08-11-2019 at 11:58 AM.
-
-
I was going to say how simple it all seems to be nowadays but will hold off on that. But back to the subject and keep my immediate thoughts to myself.....
You are really making a mountain out of a molehill if you don't mind me saying. If, as you say, a perfect post isn't an important or critical issue then centreing the little V slot for the upright grat post is absolute simplicity itself. And by using a pair of dividers, you will get the new slot EXACTLY square and EXACTLY central. Exactly right should be near enough I say.
Hold inner sleeve in 3-jaw vice and file small accurately marked out slot with model-makers triangular needle file. Make sure that you don't touch the crosswire while doing so. Done that and filed a small slot........?
Now mount .006" steel wire into a watchmakers lathe and grind the angled tip of the new post. 10 minutes work - and you'll need your eye glasses for this so get them handy.....
Lay new-made post on inner sleeve. Adjust height in relation to the crosswire, dob of glue, allow to set and there it is. Simple as falling off a log as they say around these parts.
New problem. Assemble up. If locating peg on inner sleeve (shown in photos) puts new post and crosswire 90degrees out in relation to the scope markings and segment cover, just rotate scope to suit OR rotate inner sleeve until it is correct in relation to your rifle. Drill and tap 10BA, replace anti rotation screwed peg and assemble up
What could possibly go wrong?
-
-
Legacy Member
Yeah, that is pretty straight forward!
Thanks for taking the time to lay it out like that, sometimes my brain runs away with itself... i will follow all advice.
Think my biggest issue will be sharpening the post. I have a standard lathe (Colchester Bantam) but that is a tad too big.
Maybe i need to find a watch maker who can grind me up a post or 2.
Thanks again Peter, i will update this tread with pictures as i go.
-
-
Legacy Member
Why not just find a real No32 scope to put on the rifle, or one of the copies, if it is just a prop?
There can't be too many REL No.42's around, especially in that condition. Shame to damage it
-
-
Legacy Member
I cant afford a real No.32 and i dont want to buy a reproduction.
I take your point onboard about my scope but i wouldnt say im damaging it. Just modifying it and could be put back as was at any point. Just think of all the No.42 that have been sacrificed to save a No.32.
At least mine is loved and will be enjoyed. Just like the date and Canadian connection between scope and rifle.
-
-
Roy, you’d probably want to hang me from the nearest yardarm then........I have a large cardboard box FULL of No42 & No53 tubes that I’ve nadgered over the years in order to pinch the lenses to complete needy No32’s. Other parts come in handy too, such as the segments, ocular lens retaining rings, & even the tubes themselves. Thanks to a trick taught to me by Peter years ago, even a No32 with a rusted through or torn ocular housing can be repaired with a little ‘grafting’.
-
Thank You to Roger Payne For This Useful Post: