-
Legacy Member
Low Power Loads for .303
Hi Guys,
I'd like a few hints and tips from those of you who cast your own bullets if possible.
I am thinking of producing some low power ammo for cast bullets to put through my SMLE for those days on the range when we're limited to 25 yards or so. I'm an experienced reloader but have never cast my own before.
Does anyone have any thoughts on the best approach, research on this site reveals so much information that I find myself confused!
What is recommended as a starting point, best bullet weight for low power loads, manufacturer etc., whether to size or not, whether to gas check or not, best powder and a recommended powder charge for those that have worked for you.
I seem to have so many questions but hoping you all can give me a bit of a head start.
Please do teach me to suck eggs, I won't be offended, even if that advice is "bad idea, don't do it"!
Information
|
Warning: This is a relatively older thread This discussion is older than 360 days. Some information contained in it may no longer be current. |
|
-
-
12-17-2015 06:40 PM
# ADS
Friends and Sponsors
-
Legacy Member
Welcome to the world of 303 loading. I can give you what works for me in my particular rifle but it may not work for you. First slug your bore as they vary considerably and you should size approx. 2thou over bore size. I cast projectile from wheel weights using the Lyman 314299 mould. It is a bore rider, gas check design. I gas check and size in one go to .314" I only neck size my cases as I keep them separate for each rifle. The powder I use is Hodgson Trail Boss. It is specially made for reduced loads in rifles and pistols for Cowboy Action shooting. Minimum load is 9grns and max for me is 12.7grns.I seat the projectiles out as far as I can so they just engage the rifling. I have shot the same projectile without gas checks and un sized and they were still accurate. If you read Hodgsons Reloading book (free on line) they have a section on youth loads using H4895 or ADI 2206H powder. It also tells you how to work out your loads for each calibre.
That is the tip of the iceberg. Good web sites are castboolits.reloads.com and Castpics.
Hope this helps.
-
Thank You to enfieldshooter For This Useful Post:
-
-
Legacy Member
Another path is to find a stash of projectiles designed for 7.62 x 39.
Many people pull the ball projectiles from "surplus" ammo and insert decent "hunting" SP /HP projectiles.
Some years go I snagged a few thousand "Chinese" projectiles from such an operation.
The BEST ones are the Yugoslav / Serbian types. These are "proper" bullets with a soft lead core and quality gilding-metal jacket and a .311" diameter.
Lee Enfields and AKs have the same twist rate, 1:10", just the twist "direction" is different. Even at "mild" velocities, the lighter, shorter bullets will still stabilize in that twist.
When stoked fairly hard (2900fps+), the point of impact is VERY different from Mk7 ball, usually low, oddly enough, but at least you can crank up the rear sight for such occasions.
Never thought of running them "slow", but could be good for "inoculating" young or "timid" trainees.
Alternately, you can cast your own, or, check out some of the "complete metal jacket"types, i.e. Berry's etc. and see what they offer.
Last edited by Bruce_in_Oz; 12-17-2015 at 11:34 PM.
-
Thank You to Bruce_in_Oz For This Useful Post:
-
Advisory Panel
Cast Bullet Basics For Military Surplus Rifles
By C.E. Harris Rev. 9-6-93
Cast bullet loads usually give a more useful zero at practical
field ranges with military battle sights than do full power
loads. Nothing is more frustrating than a military rifle that
shoots a foot high at a hundred yards with surplus ammo when the
sight is as low as it will go!
Do NOT use inert fillers (Dacron or kapok) to take up the excess
empty space in the case. This was once common practice, but it
raises chamber pressure and under certain conditions contributes
to chamber ringing. If a particular load will not work well
without a filler, the powder is not suitable for those conditions
of loading.
Four load classifications from Mattern (1932) cover all uses for
the cast bullet military rifle. I worked up equivalent charges
to obtain the desired velocity ranges with modern powders, which
provide a sound basis for loading cast bullets in any post-1898
military rifle from 7 mm to 8 mm:
1. 125-gr., plainbased "small game/gallery"
900-1000 f.p.s., 5 grains of Bullseye or equivalent.
2. 150-gr. plainbased "100-yd. target/small game",
1050-1250 f.p.s., 7 grs. of Bullseye or equivalent.
3. 150-180-gr. gaschecked "200-yard target"
1500-1600 f.p.s., 16 grs. of #2400 or equivalent.
4. 180-200-gr. gaschecked "deer/600-yard target"
1750-1850 f.p.s., 26 grs. of RL-7 or equivalent.
None of these loads are maximum when used in full-sized rifle
cases such as the .30-40 Krag, .303 British, 7.65 Argentine, 7.7
Jap, 7.62x54R or .30-'06. They can be used as basic load data in
most modern military rifles of 7 mm or larger, with a standard-
weight cast bullet for the caliber, such as 140-170 grains in the
7x57, 150-180 grains in the .30 calibers, and 150-190 grains in
the 8 mm. For bores smaller than 7 mm, consult published data.
The "Small Game or Gallery" Load
The 110-115-gr. bullets intended for the .30 carbine and .32-20
Winchester, such as the Lyman #311008, #311359 or #311316 are
not as accurate as heavier ones like the #311291. There isn't a
readily-available .30 cal. cast small game bullet of the proper
125-130-gr. weight. LBT makes a 130-gr. flat-nosed, GC bullet
for the .32 H&R Magnum which is ideal for this purpose. I
recommend it highly, particularly if you own a .32 revolver!
The "100-Yard Target and Small Game" Load
I use Mattern's plainbased "100-yard target load" to use up my
minor visual defect culls for offhand and rapid-fire 100-yard
practice. I substitute my usual gaschecked bullets, but without
the gascheck. I started doing this in 1963 with the Lyman
#311291. Today I use the Lee .312-155-2R, or the similar tumble-
lubed design TL.312-160-2R. Most of my rifle shooting is done
with these two basic designs.
Bullets I intend for plainbased loads are blunted using a
flatnosed top punch in my lubricator, providing a 1/8" flat which
makes them more effective on small game and clearly distinguishes
them from my heavier gaschecked loads. This makes more sense to
me than casting different bullets. Bullet preparation is easy.
I visually inspect each run of bullets and throw those with gross
defects into the scrap box for remelting. Bullets with minor
visual defects are tumble-lubed in Lee Liquid Alox without
sizing, and are used for plain-based plinkers. Bullets which are
visually perfect are sorted into groups of +/- 0.5 grain used for
200 yard matches. Gaschecks pressed onto their bases by hand
prior running into the lubricator-sizer.
For "gaschecked bullets loaded without the gascheck," for cases
like the .303 British, 7.62 NATO, 7.62x54R Russian and .30-'06 I
use 6-7 grains of almost any fast burning pistol powder,
including, but not limited to Bullseye, W-W231, SR-7625, Green
Dot, Red Dot, or 700-X. I have also had fine results with 8 to 9
grains of medium burning rate pistol or shotgun powders, such as
Unique, PB, Herco, or SR-4756 in any case of .303 British size or
larger.
. . .
The Harris "Subsonic Target" Compromise
Mattern liked a velocity of around 1250 f.p.s. for his "100-yard
target" load, because this was common with the lead-bullet .32-40
target rifles of his era. I have found grouping is best with
nongascheck bullets in military rifles at lower velocities
approaching match-grade .22 Long Rifle ammunition. I use my
"Subsonic Target" load at around 1050-1100 f.p.s. to replace both
Mattern's "small game" and "100-yard target" loads, though I have
lumped it with the latter since it really serves the same
purpose. Its report is only a modest pop, rather than a crack.
If elongated bullet holes and enlarged groups indicate marginal
bullet stability, increase the charge a half grain and try again.
If necessary increasing the charge no more than a full grain from
the minimum recommended, if needed to get consistent accuracy.
If this doesn't work, try a bullet which is more blunt and short
for its weight, because it will be more easily stabilized. If
this doesn't do the trick, you must change to a gaschecked bullet
and a heavier load.
The Workhorse Load - Mattern's "200-Yard Target"
My favorite load is the most accurate, Mattern's so-called "200-
yard target load". I expect 10-shot groups at 200 yards, firing
prone rapid with sling to average 4-5". I shoot high-
Sharpshooter/low-Expert scores across the course with an issue
03A3 or M1917, shooting in a cloth coat, using my cast bullet
loads. The power of this load approximates the .32-40,
inadequate for deer by today's standards.
Mattern's "200-yard target load" is easy to assemble. Because it
is a mild load, soft scrap alloys usually give better accuracy
than harder ones such as linotype. Local military collector-
shooters have standardized on 16 grains of #2400 as the
"universal" prescription. It gives around 1500 f.p.s. with a
150-180-gr. cast bullet in almost any military caliber. We use
16 grains of #2400 as our reference standard, just as highpower
competitors use 168 Sierra MatchKings and 4895.
The only common military rifle cartridge in which 16 grains of
#2400 provides a maximum load which must not be exceeded is in
the tiny 7.62x39 case. Most SKS rifles will function reliably
with charges of #2400 as light as 14 grains with the Lee .312-
155-2R at around 1500 f.p.s. I designed this bullet especially
for the 7.62x39, but it works very well as a light bullet in any
.30 or .303 cal. rifle.
Sixteen Grains of #2400 Is The Universal Load
The same 16 grain charge of #2400 is universal for all calibers
as a starting load. It is mild and accurate in any larger
military case from a .30-40 Krag or .303 British up through a
.30-'06 or 7.9x57, with standard-weight bullets of suitable
diameter for the caliber. This is my recommendation for anybody
trying cast bullet loads for the first time in a military rifle
without prior load development. I say this because #2400 is
not position sensitive, requires no fiber fillers to ensure
uniform ignition, and actually groups better when you just
stripper-clip load the rifle and bang them off, rather than
tipping the muzzle up to position the charge.
Similar ballistics can be obtained with other powders in any case
from 7.62x39 to .30-'06 size. If you don't have Hercules #2400
you can freely substitute 17 grains of IMR or H4227, 18 grs. of
4198, 21 grs. of Reloder 7, 24 grs. of IMR3031, or 25.5 grs. of
4895 for comparable results. However, these other powders may
give some vertical stringing in cases larger than the 7.62x39
unless the charge is positioned against the primer by tipping the
muzzle up before firing. Hercules #2400 does not require this
precaution. Don't ask me why. Hercules #2400 usually gives
tight clusters only within a narrow range of charge weights
within a grain or so, and the "universal" 16 grain load is almost
always best. Believe me, we have spent a lot of time trying to
improve on this, and you can take our word for it.
The beauty of the "200-yard target load" at about 1500 f.p.s. is
that it can be assembled with bullets cast from the cheapest
inexpensive scrap alloy, and fired all day without having to
clean the bore. It ALWAYS works. Leading is never a problem.
Once a uniform bore condition is established, the rifle behaves
like a .22 match rifle, perhaps needing a warming shot or two if
it has cooled, but otherwise being remarkably consistent. The
only thing I do after a day's shoot is to swab the bore with a
couple of wet patches of GI bore cleaner or Hoppe's, and let it
soak until the next match. I then follow with three dry patches
prior to firing. It only takes about three foulers to get the
03A3 to settle into tight little clusters again.
"Deer and Long Range Target" Load
Mattern's "deer and 600 yard target load" can be assembled in
cases of .30-40 Krag capacity or larger up to the .30-'06 using
18-21 grs. of #2400 or 4227, 22-25 grs. of 4198, 25-28 grs. of
RL-7 or 27-30 grs. of 4895, which give from 1700-1800 f.p.s.,
depending on the case size. These charges must not be used in
cases smaller than the .303 British without cross-checking
against published data! The minimum charge should always be used
initially, and the charge adjusted within the specified range
only as necessary to get best grouping. Popular folklore
suggests a rifle barrel must be near perfect for good results
with cast bullets, but this is mostly bunk, though you may have
to be persistent.
I have a rusty-bored Finnish M28/30 which I have shot
extensively, in making direct comparisons with the same batches
of loads on the same day with a mint M28 and there was no
difference. The secret in getting a worn bore to shoot
acceptably is remove all prior fouling and corrosion. Then you
must continue to clean the bore "thoroughly and often" until it
maintains a consistent bore condition over the long term. You
must also keep cast bullet loads under 1800 f.p.s. for hunting,
and under 1600 for target work.
A cleaned and restored bore will usually give good accuracy with
cast bullet loads if the bullet fits the chamber THROAT properly,
is well lubricated and the velocities are kept below 1800 f.p.s.
The distinction between throat diameter and groove diameter in
determining proper bullet size is important. If you are unable
to determine throat diameter from a chamber cast, a rule of thumb
is to size bullets .002" over groove diameter, such as .310" for
a .30-'06, .312" for a 7.62x54R and .314" for a .303 British.
"Oversized .30s" like the .303 British, 7.7 Jap, 7.65 Argentine,
7.62x39 Russian and frequently give poor accuracy with .30 cal.
cast bullets designed for U.S. barrels having .300 bore and .308
groove dimensions, because the part of the bullet ahead of the
driving bands receives no guidance from the lands in barrels of
larger bore diameter. The quick rule of thumb to checking proper
fit of the forepart is to insert the bullet nose first into the
muzzle. If it enters to clear up to the front driving band
without being noticeably engraved, accuracy will seldom be
satisfactory.
The forepart is not too large if loaded rounds can be chambered
with only slight resistance, the bullet does not telescope back
into the case, or to stick in the throat when extracted without
firing. A properly fitting cast bullet should engrave the
forepart positively with the lands, and be no more than .001"
under chamber throat diameter on the driving bands. Cast bullets
with a tapered forepart at least .002" over bore diameter give
the best results.
. . .
So now you have enough fundamentals to get started. If you want
to have fun give that old military rifle try. You'll never know
the fun you've been missing until you try it!
In Home Mix We Trust, Regards, Ed
-
The Following 5 Members Say Thank You to Parashooter For This Useful Post:
-
Legacy Member
Thanks guys for the great response. That's given me a great head start.
-
-
Legacy Member
My favourite load for short range .303 is a gas checked Lyman 314299 cast bullet on top of 11.9gn Unique.. (i.e. the 1.3cc Lee powder scoop)
easy 3/4" groups at 30m.. I have been using this load for over ten years and have never had any problems with it.. must have fired thousands of rounds!
...works for 7.62x54R as well!
-
The Following 2 Members Say Thank You to bombdoc For This Useful Post:
-
Advisory Panel
I'd just use a light load on the recommendation of the book. I'd also use a light bullet as recommended..."Light" loads can be very dangerous. Parashooter has given you most of the info I think...
-
-
Legacy Member
There is a lot of tested cast bullet loads in the Lyman Cast Bullet handbook. There are a few RCBS Cast bullet handbooks around but I think the prices of them have inflated.
You can find either one on eBay USA.
Later Speer Manuals (11, 12, 13) have reduced load data for jacked bullets. Unfortunately the primary rifle powder was SR4759 which has been discontinued. You probably didn't see it much in the UK but 4227 is very close in burning rate and charges. This can be verified in old IMR data booklets that you can find in electronic form. These booklets date from the 1960s to the early 1980s.
Cast bullet loads require that your bullet body be about .001 to .002 larger than the groove diameter. If you intend to go faster than about 1300 FPS plan on being an advanced cast bullet guy or just use gas checked bullets.
You need a expander such as a Lyman M die to properly expand the cases.
With the large variations in Lee-Enfield barrels you should slug your bore and find a bullet that fits the groove diameter (body) and one with a nose large enough that it will not slump. The bullet nose needs to be large enough to be supported by the top of the lands so it does not bend to one side.
-