-
Legacy Member
Originally Posted by
cprher
I found this one with the help of Google. Anyone have a better one?
If it any help this is the one published in the book "Textbook of Small Arms 1928"
It is the military dimensions of the cartridge and chamber.
Note - non of this 'namby pamby make it thin' requirement as per the SAAMI drawings 0.064" +0/-0.01" (military requirement for case rims was 0.058" to 0.064")
And the chamber dimensions from the 1943 dated blueprints (engineering drawings) for the No1 Mk3 which I think you have already seen.
I have the set of fully dimensioned drawing of every part and component of the No1 Mk3 but they are too large to post on the forum.
A 'small fraction' of one of the series of drawings :
https://i.postimg.cc/s2v2ZCWS/No1-Mk...mensions-2.png
https://i.postimg.cc/rFrCx7SB/Screenshot-2292.png
Last edited by Alan de Enfield; 10-11-2023 at 09:48 AM.
Mine are not the best, but they are not too bad. I can think of lots of Enfields I'd rather have but instead of constantly striving for more, sometimes it's good to be satisfied with what one has...
-
The Following 2 Members Say Thank You to Alan de Enfield For This Useful Post:
-
10-11-2023 09:33 AM
# ADS
Friends and Sponsors
-
Legacy Member
"Mil-Spec" .303 chambers are just weird.
From the very beginning to at least the No4 days, they were NOT cut using "modern-style", one-piece 'reamers.
They were cut using a series of odd little short reamers, one for each "feature" of the chamber. There was a =n associated set of gauges used to measure each different stage.
The best bit is that final "setting" of the chamber was achieved by firing a "special" cartridge closely related to a "proof' round, to settle the insides of the chamber AND "final seat" the barrel, bolt and body assembly. Remember that all of those Lee Enfields were made from various grades of metal ranging from glorified "mild steel" to malleable cast iron.
I will see if I can find the full description of the process in my tree-ware files.
Let's face it: NOBODY was expecting to be reloading the "once-fired" brass, especially on the two-way range. As long as the brass case sealed the pressure in the barrel and was then extracted in one piece, NOBODY cared.
And then, there are all the "surplus" rifles that have had their chambers"freshened-up" for commercial sale. On a rimmed case this is bad enough, but when you start seeing WW2 Mausers with a millimetre of headspace BEYOND the "No Go' gauge, sphincters start to twitch.
The past is an "interesting" place.
-
The Following 2 Members Say Thank You to Bruce_in_Oz For This Useful Post:
-
-
Legacy Member
There is an excellent booklet (63 pages) that explains the manufacturing process of the Lee Enfield barrels. It is a 'modern' compilation of a series of articles ("Machining The Lee-Enfield Barrel - Operations and Fixtures Employed" written for 'Machinery Magazine' & published in 1916.
Booklet called "Making Rifle Barrels" and is ISBN 1-55918-280-6 Reprinted by Lindsay Publications in 2002.
Example of a couple of the many pages on the chamber :
Edit apologies that the pages are on their side - I cannot seem to be able to rotate them.
Last edited by Alan de Enfield; 10-14-2023 at 03:28 AM.
Mine are not the best, but they are not too bad. I can think of lots of Enfields I'd rather have but instead of constantly striving for more, sometimes it's good to be satisfied with what one has...
-
The Following 3 Members Say Thank You to Alan de Enfield For This Useful Post:
-
Advisory Panel
“There are invisible rulers who control the destinies of millions. It is not generally realized to what extent the words and actions of our most influential public men are dictated by shrewd persons operating behind the scenes.”
Edward Bernays, 1928
Much changes, much remains the same.
-
The Following 2 Members Say Thank You to Surpmil For This Useful Post: