Results 1 to 10 of 22

Thread: Nasty situation adverted!

Click here to increase the font size Click here to reduce the font size

Threaded View

  1. #1
    Contributing Member CINDERS's Avatar
    Join Date
    Nov 2009
    Last On
    04-28-2024 @ 12:33 PM
    Location
    South West Western Australia
    Posts
    7,765
    Real Name
    CINDERS
    Local Date
    05-01-2024
    Local Time
    09:29 AM

    Nasty situation adverted!

    I was loading cases today for my 6.5 x 284 which some have called the Fat Swede
    Anyway I am about finished the first batch of 24 as I was changing the load spec's for the next batch of 12 (you have to experiment a little with stuff). (from 30 thou jump to 10 thou jam)
    Maybe it was all the rounds I have loaded over the years because my Redding BR thrower is usually smack on though Reloader powder is not the best feeding powder, but something was amis!
    I had 5 to go so I paused and checked all over again and there it was the point slider on my Lee balance scale I had inadvertently knocked and it had come loose and moved forward increasing the load, its done a few thousand rounds and is worn time to replace it I think.

    When I dropped a previously loaded case on the pan it shot straight to the top and as I was already at a heavy loading this would have pushed it over the top for sure.
    So re set the slider worked backwards until I hit the one that zeroed at the 52 grains required adjusting all the other cases back (8 in total ) all is now good.
    And having a narrow squeak 2 years ago is still pretty fresh in my mind as why the action did not let go or a case rupture I have no idea but it did crack the back of the bolt where it is milled out for the stud (Savage action) discovered by accident 1 month later.

    How I found that was it kept knocking the safety on when extracting as the rear of the bolt had drooped so on intricate examination it was revealed goodness me.
    I put it all together from that one event where I suffered a flash over and the round detonated rather than burn.
    I was chasing a low density load of ball powder with low pressure but reasonable velocity it did not work also I was using a magnum primer.
    My loading's now are at 90 - 95% of case capacity I do not play so much anymore only bullet jump and minor load adjustments dependent on tried and proven powders/loads. Rifle has been checked over by my gunsmith a new bolt and re head spaced all is good.

    But just goes to show you to be for ever vigilante when your doing stuff with or for your fire arms.
    Cheers .Attachment 80516
    Information
    Warning: This is a relatively older thread
    This discussion is older than 360 days. Some information contained in it may no longer be current.

  2. The Following 5 Members Say Thank You to CINDERS For This Useful Post:


Similar Threads

  1. Replies: 8
    Last Post: 10-03-2012, 02:47 PM
  2. this primer situation getting out of hand
    By Pelago in forum Ammunition and Reloading for Old Milsurps
    Replies: 25
    Last Post: 05-01-2010, 12:26 PM
  3. Need advice for trafic situation
    By Timmer in forum The Watering Hole OT (Off Topic) Forum
    Replies: 24
    Last Post: 07-24-2009, 09:08 AM
  4. Oddball situation at the local dealer...
    By Bob Womack in forum M1 Garand/M14/M1A Rifles
    Replies: 22
    Last Post: 03-04-2009, 12:23 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts