+ Reply to Thread
Results 1 to 8 of 8

Thread: Theoretical exercise

Click here to increase the font size Click here to reduce the font size
  1. #1
    Legacy Member Bruce_in_Oz's Avatar
    Join Date
    Jun 2008
    Last On
    Yesterday @ 05:39 AM
    Location
    Brisbane
    Posts
    2,232
    Local Date
    03-19-2024
    Local Time
    02:09 PM

    Theoretical exercise

    Having a chat with a few fellow ex-armourers a while back.

    The subject of "product-improving" various weapons came up, as usual, but the main topic was the M-60 GPMG.

    The U.S. military seems to be keeping the old girl alive to a limited extent, but, over the years, has anybody in the "freelance" field done anything creative?

    General thoughts run to adapting a Mag-58 / M-240 or MG-3 feed system to the top and the FN-style, disconnector-equipped trigger mech. to the bottom end.

    PKM- or M-240 style adjustable front-sight assembly?

    And a Mk 1 Bren bipod "somewhere" in the mix.

    Stuff we can only dream about here.
    Information
    Warning: This is a relatively older thread
    This discussion is older than 360 days. Some information contained in it may no longer be current.

  2. # ADS
    Friends and Sponsors
    Join Date
    October 2006
    Location
    Milsurps.Com
    Posts
    All Threads
    A Collector's View - The SMLE Short Magazine Lee Enfield 1903-1989. It is 300 8.5x11 inch pages with 1,000+ photo’s, most in color, and each book is serial-numbered.  Covering the SMLE from 1903 to the end of production in India in 1989 it looks at how each model differs and manufacturer differences from a collecting point of view along with the major accessories that could be attached to the rifle. For the record this is not a moneymaker, I hope just to break even, eventually, at $80/book plus shipping.  In the USA shipping is $5.00 for media mail.  I will accept PayPal, Zelle, MO and good old checks (and cash if you want to stop by for a tour!).  CLICK BANNER to send me a PM for International pricing and shipping. Manufacturer of various vintage rifle scopes for the 1903 such as our M73G4 (reproduction of the Weaver 330C) and Malcolm 8X Gen II (Unertl reproduction). Several of our scopes are used in the CMP Vintage Sniper competition on top of 1903 rifles. Brian Dick ... BDL Ltd. - Specializing in British and Commonwealth weapons Specializing in premium ammunition and reloading components. Your source for the finest in High Power Competition Gear. Here at T-bones Shipwrighting we specialise in vintage service rifle: re-barrelling, bedding, repairs, modifications and accurizing. We also provide importation services for firearms, parts and weapons, for both private or commercial businesses.
     

  3. #2
    Advisory Panel Lee Enfield's Avatar
    Join Date
    Oct 2006
    Last On
    03-16-2024 @ 12:24 PM
    Location
    out there
    Posts
    1,820
    Local Date
    03-18-2024
    Local Time
    10:09 PM
    The aluminum top cover was just stupid.

    The bipod on the barrel (of the originals) was just stupidity illustrating a lack of end user input.

    The bolts and firing pin issues...need i say more?...

    Ingenius theory, impractical design...

  4. Avoid Ads - Become a Contributing Member - Click HERE
  5. #3
    Legacy Member Bruce_in_Oz's Avatar
    Join Date
    Jun 2008
    Last On
    Yesterday @ 05:39 AM
    Location
    Brisbane
    Posts
    2,232
    Local Date
    03-19-2024
    Local Time
    02:09 PM
    Thread Starter
    In a military system, there is a huge logistical tail . Every battalion has some sort of workshop element, to handle weapons, vehicles, radios, generators, etc.

    In an operational environment, damaged or faulty equipment, including weapons are usually dealt with, initially, by the simple practice of "one-for-one", i.e., "New guns for old". Then the broken toy is properly assessed in the workshop and either repaired in situ or booted up the food-chain to a higher-level facility.

    In "civilian" situations, this is not always possible, to say the least.

    I spent a bit of time with the old M-60, both as a "consumer" and as n armourer. Kept clean and CORRECTLY lubricated and with ALL parts up to spec, they would run quite happily. When we used them in a sustained-fire role off tripods, barrel-changes were done at appropriate intervals and guns were periodically taken "off-line" for a quick clean and re-lube. Burning through thousands of rounds with the trigger held back was absolutely not on the dance-card.

    Fired off the bipod, bursts of five to ten rounds are the way to go. In "fire and movement", the machine-gun will lay down several of these bursts (suppressive fire) as the other "fire-team", the "rifle-group" tries to maneuver to a better tactical position. Then as they take up that position, they start applying fire to the objective and the MG group will re-deploy. This "leap-frogging" continues until the objective is overwhelmed or Murphy steps in.

    NEVER "dry-fire" an M-60 because doing so risks damaging both the bolt locking lugs AND the locking collar at the rear of the barrel. The act of feeding in a brass-cased cartridge actually "buffers" the closing of the breech. If you are into "blank firing" NEVER use any of the plastic blanks. These cause two problems, long term: As the bolt shoves the plastic blank into the chamber, it compresses it and the bolt lugs will engage the locking collar more violently than usual. Secondly, unlike brass cases, plastic ones do not carry away as much heat from the chamber as brass ones, this the gun runs "hotter".

    Finally, the extractor and ejector must always be CLEAN and lightly lubed. Firing residue accumulates in the inner spaces occupied by these two components. That alone will make their function sluggish. the accumulated crud seems to attract and retain moisture. Regular (every few thousand rounds, more if you live in a "dry" place) stripping and cleaning of these parts is advised. If you prefer to NOT strip these parts out regularly, at least stand a fired bolt nose-down in a container of solvent for a while, then "work" the extractor and ejector manually until nasty stuff stops running out. Repeat until the "drainage" runs clean, then re-oil.

    If springs are below nominal length and / or corroded / pitted, replace them immediately. This applies to ALL the springs, from the main return spring to the tiny ones in the feed mechanism. It was our normal practice before a live shoot, to do a total strip and examination and any part looking slightly shabby was replaced. We also went to the shoot with lots of spares, most of which came home unused, because the guns were almost like new before the fun started.

  6. Thank You to Bruce_in_Oz For This Useful Post:


  7. #4
    Legacy Member RCS's Avatar
    Join Date
    Mar 2009
    Last On
    Yesterday @ 10:56 PM
    Location
    USA
    Posts
    4,314
    Real Name
    Robert Seccombe
    Local Date
    03-18-2024
    Local Time
    11:09 PM

    M60 m/g

    Long time ago when i was an armorer in the US Army and later in the reserve, I worked with the Model 1919A6 which was very well liked. As the M60 started to replace the old BMG, we received new examples that had the R stamped indicating the feed ramp was altered to prevent a live round from striking a chambered round as I remember.

    When a firing pin broke in the field, the weapon was very difficult to take apart and had to be returned for repair. I saved a broken firing and spring as a reminder. Also the spring that held the trigger group to the receiver would come off and get lost tooAttachment 106328

  8. #5
    Advisory Panel Surpmil's Avatar
    Join Date
    Feb 2008
    Last On
    @
    Location
    West side
    Posts
    4,648
    Local Date
    03-18-2024
    Local Time
    09:09 PM
    So in other words: not soldier proof or reliable. But on the other hand it was "invented there" (at least superficially)
    “There are invisible rulers who control the destinies of millions. It is not generally realized to what extent the words and actions of our most influential public men are dictated by shrewd persons operating behind the scenes.”

    Edward Bernays, 1928

    Much changes, much remains the same.

  9. #6
    Advisory Panel browningautorifle's Avatar
    Join Date
    Jul 2008
    Last On
    Yesterday @ 12:51 PM
    Location
    Victoria BC
    Posts
    29,810
    Real Name
    Jim
    Local Date
    03-18-2024
    Local Time
    09:09 PM
    I was issued an M60 for two months in Australiaicon in 1977 and used it every day there both live and blank...
    Quote Originally Posted by Bruce_in_Oz View Post
    NEVER use any of the plastic blanks.
    We had nothing but problems with the then issued plastic blanks and even then I knew I wanted brass blanks for use. We had double feeds at times once the gun got hot, except once it was five that came out when I removed the barrel. They were all crammed side by side into a hot chamber. Nice to carry, crap to use. Worked OK in the SLRs I guess, I didn't have one. Shooting live gave no trouble, my gun had an early number and for sure went to RVN with RAR as they'd just come back. I used to have the number here...?

    Quote Originally Posted by RCS View Post
    Also the spring that held the trigger group to the receiver would come off and get lost too
    The Australians had us put that flat spring on from the top to eliminate losing it and having a full time auto with no shut off...fire a belt at a time...

    No machine gun is soldier proof, the MAG/C6 when new was about closest thing I saw. Once they were worn, they still required savvy to keep them in top shape in action. You can't always get maintenance you see. I also used the 1919A4 guns and they were old, you had to be very mechanical to keep some running. Once you understood how they worked, it was key to keeping them going.
    Regards, Jim

  10. #7
    Legacy Member RCS's Avatar
    Join Date
    Mar 2009
    Last On
    Yesterday @ 10:56 PM
    Location
    USA
    Posts
    4,314
    Real Name
    Robert Seccombe
    Local Date
    03-18-2024
    Local Time
    11:09 PM

    modified M60 in Viet Nam

    Navy Seals did use a modified M60 during the Viet Nam war. Note the shorter barrel and
    front sight removed in this photo. The Stoner weapons were well used too.Attachment 106372

  11. #8
    Legacy Member pocketshaver's Avatar
    Join Date
    Dec 2018
    Last On
    09-23-2020 @ 04:17 AM
    Location
    usa
    Posts
    229
    Local Date
    03-18-2024
    Local Time
    11:09 PM
    actually just go back to MG40. fully chromed and melonited barrels would be the only change

+ Reply to Thread

Similar Threads

  1. Theoretical question about a CMP M1 Carbine
    By kiotiugly in forum M1/M2 Carbine
    Replies: 7
    Last Post: 03-13-2016, 10:23 AM
  2. Replies: 0
    Last Post: 11-13-2015, 03:08 AM
  3. Time to get the model 99 out and give it some exercise
    By Thumper in forum Japanese Rifles
    Replies: 10
    Last Post: 11-27-2011, 10:06 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Raven Rocks