Thank you gentlemen for your guidance on this project.
Type: Posts; User: jangle; Excluded Forums: Milsurp Knowledge Libraries (READ ONLY)
Thank you gentlemen for your guidance on this project.
Hello,
A little out of my area here but I'm acquiring a 1946 No.5 Mk1, that has lost the top handguard. I've read through a few threads concerning similar issues, but most refer to the lower...
Your ladder is a Kokura made sight.
Probably what has happened back through its life, all the "bells & whistles" were removed (mono-pod, cleaning rod, AA wings etc) and someone then found a pair...
One thing about collecting Japanese firearms is, one should never say never, but I have never seen a rear sight on a Kokura manufactured rifle, that wasn't made by Kokura, and visa versa with the...
Congratulations on your pick up. Don't sweat the bolt release. It probably has dried grease caked inside and would be sticky.
Your rear sight was not made by the Kokura Arsenal (the AA wings for...
IMHO, I believe your rifle isn't late enough for the short rod you mention. If I were you, I would go ahead and purchase a standard 99 rod (23 3/4") and install it. Rifles that took the shorter...
Correct.
If you have the rifle apart, you will see the main rifles assembly number 476 on the bottom of the receiver. The bayonet latch button is a three digit number (670), probably proceeded by...
The assembly number of the latch is completely different from the rifle receiver assembly number.
It's not uncommon to see the cross-hatch mis-aligned on this part. For whatever reason, some...
The latch parts have a separate assembly number, so if your bayonet housing matches the last three digits of serial number you're good to go, and you have a matching bayonet assembly.
The reticle on 4x scopes are not canted (slanted) like the 2.5x Type 97 scopes, so if this one is, it's because the inside etched glass has gotten rotated slightly.
You have to remember that the...
Sounds like you're doing about all you can. Maybe one of the old pipe cleaners might let you reach a little higher etc. I wouldn't spray any kind of penetrating oil up in there to loosen the grim...
Nice addition to your collection!
Supposedly there were a small number of "short barreled" T-99 Carbines found at wars end at the Jinsen Arsenal in Korea. I've never personally held one, have seen a photo or two. I think "Military...
With the quality of the rifles, and a larger serial number (above 3 digit), these were originally standard issue T-30 rifles with proper receiver stamps, including the Mum. The receivers were ground...
The first four photos are of a T-30 rifle that was removed from military service and converted to a smooth bore training rifle.
The original receiver T-30 markings and Chrysanthemum were removed and...
The term "Last Ditch" is a phrase coined by US collectors over the years to identify with the late Type 99 rifles where the deletion of parts through the production period included:
front sight...
Your rifle was made at the Toriimatsu factory of Nagoya Army Arsenal. It is an 11th series and was made in 1945.
Long time Japanese WWII collector wishing to purchase "collector quality" T-14's and T-94's. Specifically looking for a T-14 small trigger guard, 15 date with 1-3 digit serial number, and other low...
Your stock is the correctly proofed stock for TJK.
It looks like the rifle had both, the mono-pod and a sliding dust cover at one time. You can see the faint lines, as you mentioned, in the lower...
This is a common occurrence in Japanese firearms where there is not a clean cut designation in serial numbers between a change in components.
If your forestock wood and rear band shows no evidence...
+1 ;)
Your receiver was stamped between xxx and xxx '43.
A 4th series Carbine made at Chigusa factory of the Nagoya Army Arsenal. Probably 1937.
Nice piece Aragorn. You did well!
Randy,
The reason I asked if all bolt parts are matching is a 99 safety and firing pin are different from a 38 safety/firing pin and not interchangeable.
If you haven't done so, remove the bolt...