+ Reply to Thread
Page 1 of 2 1 2 LastLast
Results 1 to 10 of 13

Thread: Mk1 vs. Mk2 Buttstock Return Springs

Click here to increase the font size Click here to reduce the font size
  1. #1
    Legacy Member hatrick's Avatar
    Join Date
    Sep 2008
    Last On
    Yesterday @ 06:16 PM
    Location
    Massachusets, USA
    Posts
    142
    Local Date
    10-31-2024
    Local Time
    07:45 PM

    Mk1 vs. Mk2 Buttstock Return Springs

    Is the Mk1 return spring the same as the outer Mk2 return spring and the only difference is they added a smaller second inner spring on the Mk2?

    I was assembling my Mk1 buttstock and a dual Mk2 spring set fits no problem and it seems a bit stiffer than the single Mk1 spring (which seems like a good thing). Any issues using a Mk2 spring set in a Mk1 buttstock?

    Thanks
    Information
    Warning: This is a relatively older thread
    This discussion is older than 360 days. Some information contained in it may no longer be current.

  2. # ADS
    Friends and Sponsors
    Join Date
    October 2006
    Location
    Milsurps.Com
    Posts
    All Threads
    A Collector's View - The SMLE Short Magazine Lee Enfield 1903-1989. It is 300 8.5x11 inch pages with 1,000+ photo’s, most in color, and each book is serial-numbered.  Covering the SMLE from 1903 to the end of production in India in 1989 it looks at how each model differs and manufacturer differences from a collecting point of view along with the major accessories that could be attached to the rifle. For the record this is not a moneymaker, I hope just to break even, eventually, at $80/book plus shipping.  In the USA shipping is $5.00 for media mail.  I will accept PayPal, Zelle, MO and good old checks (and cash if you want to stop by for a tour!).  CLICK BANNER to send me a PM for International pricing and shipping. Manufacturer of various vintage rifle scopes for the 1903 such as our M73G4 (reproduction of the Weaver 330C) and Malcolm 8X Gen II (Unertl reproduction). Several of our scopes are used in the CMP Vintage Sniper competition on top of 1903 rifles. Brian Dick ... BDL Ltd. - Specializing in British and Commonwealth weapons Specializing in premium ammunition and reloading components. Your source for the finest in High Power Competition Gear. Here at T-bones Shipwrighting we specialise in vintage service rifle: re-barrelling, bedding, repairs, modifications and accurizing. We also provide importation services for firearms, parts and weapons, for both private or commercial businesses.
     

  3. #2
    Legacy Member Ammoman's Avatar
    Join Date
    Dec 2015
    Last On
    10-08-2023 @ 08:22 AM
    Location
    Surrey, England
    Age
    64
    Posts
    8
    Real Name
    Clifford
    Local Date
    11-01-2024
    Local Time
    12:45 AM
    It says in the manual "Two spring constitute the Mark 2; Mark 1 is shorter, using one spring."
    VOCAB # BE 1813 for the Mk 1 and VOCAB #'s BE 6896 and BE 6897 for the MK 2

    So I'm guessing the MK 1 butt may be a bit shorter so using a double spring might be a bit too strong to use as a direct replacement.
    Last edited by Ammoman; 02-08-2023 at 02:41 AM.

  4. Avoid Ads - Become a Contributing Member - Click HERE
  5. #3
    Advisory Panel Lee Enfield's Avatar
    Join Date
    Oct 2006
    Last On
    Yesterday @ 02:24 PM
    Location
    out there
    Posts
    1,838
    Local Date
    10-31-2024
    Local Time
    05:45 PM
    Here is the 1955 Canadianicon EME springs use in the Bren.

    I suspect that the MkI spring had more than 6 coils (probably a typo?).
    Attached Thumbnails Click image for larger version

Name:	IMG_20160418_151223.jpg‎
Views:	208
Size:	1.58 MB
ID:	129983   Click image for larger version

Name:	IMG_20160418_151212.jpg‎
Views:	189
Size:	1.31 MB
ID:	129984   Click image for larger version

Name:	IMG_20160418_151151.jpg‎
Views:	188
Size:	1.07 MB
ID:	129985  
    Last edited by Lee Enfield; 02-09-2023 at 12:08 PM.
    BSN from the Republic of Alberta

    http://www.cartridgecollectors.org/

  6. #4
    Legacy Member hatrick's Avatar
    Join Date
    Sep 2008
    Last On
    Yesterday @ 06:16 PM
    Location
    Massachusets, USA
    Posts
    142
    Local Date
    10-31-2024
    Local Time
    07:45 PM
    Thread Starter
    This is for my Historic Arms semi auto Bren. Right now it has a single Mk2 outer spring and I was thinking of going to the double spring for a bit more recoil protection.

  7. #5
    Advisory Panel
    Peter Laidler's Avatar
    Join Date
    Jul 2008
    Last On
    10-20-2024 @ 05:01 AM
    Location
    Abingdon, Oxfordshire. The home of MG Cars
    Posts
    16,569
    Real Name
    Peter Laidler
    Local Date
    11-01-2024
    Local Time
    12:45 AM
    The double return spring was to counter the extra impetus to the breech block and piston assembly. This was caused by the increase in diameter of the gas hole in the barrel (Mk1 to Mk1* barrel). As a result the working parts hit the buffer plate with such force that it cracked the buffer plate where it joins the rounded part at the rear.

    Opening up the gas port also caused a more violent unlocking of the breech block by the piston post. This resulted in the piston post spring breaking and thus, the piston post spring plunger bottoming out and rounding the bottom end........... A real dogs dinner! So the piston post plunger was replaced with a shorter one.

    And the buffer plate STILL cracked in the circular area on the face. BUT, to make life easier for the gun crews, a spare piston post spring was always kept in the spare parts tin, in the wallet or holdall

    As a bit part amateur regarding Brens, I say that the OUTER spring remained the same.

  8. The Following 6 Members Say Thank You to Peter Laidler For This Useful Post:


  9. #6
    Advisory Panel browningautorifle's Avatar
    Join Date
    Jul 2008
    Last On
    Today @ 06:59 PM
    Location
    Victoria BC
    Posts
    30,402
    Real Name
    Jim
    Local Date
    10-31-2024
    Local Time
    04:45 PM
    Quote Originally Posted by Peter Laidlericon View Post
    As a bit part amateur regarding Brens
    I was hoping you'd see this post.
    Regards, Jim

  10. #7
    Advisory Panel
    Peter Laidler's Avatar
    Join Date
    Jul 2008
    Last On
    10-20-2024 @ 05:01 AM
    Location
    Abingdon, Oxfordshire. The home of MG Cars
    Posts
    16,569
    Real Name
    Peter Laidler
    Local Date
    11-01-2024
    Local Time
    12:45 AM
    The classic Bren total fiasco was machining gas escape in the gas cylinder, DIRECTLY underneath the bipod sleeve. Have a look at a Mk1 gas cylinder. Have you ever heard of such folly? The instructions said that after every couple of magazines, the gun crew should twist the gun on the bipod - left to right to left - a few times to break the carbon away. Good idea - if, during the heat of battle in Franceicon in May and June 1940, they remembered to do so. One or two (?) didn't...... The result was a bipod stuck solid on the gas cylinder. Even WORSE was the crews that DID remember to twist the gun on the bipod. The diamond hard carbon fouling was harder than the poor stainless (?) steel gas cylinder. So within a short time the gas cylinder and bipod sleeve were ground down, the gas escaped and soon was insufficient to cock the gun.

    The quick fix was to increase the gas by reaming out the gas prts in the barrel.

    Even BETTER was that for the first 5 years of production and service, until 1943 or so, Locking shoulders were not supplied as spare parts. So a worn out gun with oversize CHS remained a worn out gun with excess CHS..

    As for the pure horse manure that the gun was so accurate that it could be used as a sniper rifle...................

    But all that said, I loved it to bits. No doubt, the best incarnation was the Mk3 that had all the troubles ironed out and into the L4 A4. Just providing that you told the young Armourers in no uncertain terms, that you must never, ever, not NEVER rush a job working on a Bren.

  11. The Following 4 Members Say Thank You to Peter Laidler For This Useful Post:


  12. #8
    Contributing Member csmarcher's Avatar
    Join Date
    Sep 2008
    Last On
    09-17-2024 @ 12:31 PM
    Location
    In the shed
    Posts
    119
    Real Name
    Gary
    Local Date
    10-31-2024
    Local Time
    03:45 PM
    Quote Originally Posted by Peter Laidlericon View Post
    The classic Bren total fiasco was machining gas escape in the gas cylinder, DIRECTLY underneath the bipod sleeve. Have a look at a Mk1 gas cylinder. Have you ever heard of such folly? The instructions said that after every couple of magazines, the gun crew should twist the gun on the bipod - left to right to left - a few times to break the carbon away. Good idea - if, during the heat of battle in Franceicon in May and June 1940, they remembered to do so. One or two (?) didn't...... The result was a bipod stuck solid on the gas cylinder. Even WORSE was the crews that DID remember to twist the gun on the bipod. The diamond hard carbon fouling was harder than the poor stainless (?) steel gas cylinder. So within a short time the gas cylinder and bipod sleeve were ground down, the gas escaped and soon was insufficient to cock the gun.

    The quick fix was to increase the gas by reaming out the gas prts in the barrel.

    Even BETTER was that for the first 5 years of production and service, until 1943 or so, Locking shoulders were not supplied as spare parts. So a worn out gun with oversize CHS remained a worn out gun with excess CHS..

    As for the pure horse manure that the gun was so accurate that it could be used as a sniper rifle...................

    But all that said, I loved it to bits. No doubt, the best incarnation was the Mk3 that had all the troubles ironed out and into the L4 A4. Just providing that you told the young Armourers in no uncertain terms, that you must never, ever, not NEVER rush a job working on a Bren.

    Love your posts and replies, there is always an interesting story, anecdote or tip for us Bren collectors and shooters !!!
    The greatest LMG to ever see service in the British Army...........................

  13. The Following 2 Members Say Thank You to csmarcher For This Useful Post:


  14. #9
    Advisory Panel
    Peter Laidler's Avatar
    Join Date
    Jul 2008
    Last On
    10-20-2024 @ 05:01 AM
    Location
    Abingdon, Oxfordshire. The home of MG Cars
    Posts
    16,569
    Real Name
    Peter Laidler
    Local Date
    11-01-2024
    Local Time
    12:45 AM
    Thanks for your comments Company Sgt Major Archer. The initial problems with the Bren lay at the door of the committees and dare I say it, the trials and testing teams from the old small arms school at Hythe. Everyone, from the War Office downwards wanted the gun to be all things to all men. They wanted a jack of all trades.............. But when it came to push and shove and when the going got tough, that's when the Bren really excelled and the tough got going. As tough as old boots........ The only job it really excelled at was the Infantry section light machine gun. It was never any good as a sustained fire machine gun or in the AA fire role or overhead fire support role or to replicate the 2" mortar fire. Taught to EVERY recruit in his basic training. This ensured that every soldier was capable of using the section machine gun. Unlike the Vickers teams who were specialised

    Did I love it to bits? Yes. Do I still remember all of the gauge sizes ? Yes. Repair procedures and methods....... Yep!

  15. The Following 3 Members Say Thank You to Peter Laidler For This Useful Post:


  16. #10
    Contributing Member csmarcher's Avatar
    Join Date
    Sep 2008
    Last On
    09-17-2024 @ 12:31 PM
    Location
    In the shed
    Posts
    119
    Real Name
    Gary
    Local Date
    10-31-2024
    Local Time
    03:45 PM
    Peter

    Timing is a funny thing....a friend of mine here in the US has just had a Bren Mk II rebuilt/restored into a functioning semi auto, and brought it over to me as he had a few questions.

    To my horror and astonishment the builder who restored it built it with an early Mk I gas cylinder with all the additional holes under the bipod. I told him in no uncertain terms to get the gun back to the builder and replace that with a Mk II cylinder which I had in my spare parts box or he would have nothing but nightmares getting the gun to run reliably !!!

    My thoughts went immediately back to your advice here on the forum !!!

    So, once again, thanks Peter for all your great Bren advice !!

    Regards from California

    Gary Archer
    The greatest LMG to ever see service in the British Army...........................

+ Reply to Thread
Page 1 of 2 1 2 LastLast

Similar Threads

  1. M1 CARBINE REPLACMENT SPRINGS AND MAG SPRINGS
    By bros in forum WTS/WTB/WTT (Want to Sell, Buy or Trade) Forum
    Replies: 0
    Last Post: 01-13-2021, 02:44 PM
  2. Sterling Mk4 / L2A3 Return Springs
    By Vincent in forum Other LMG/HMG and SMG Forum
    Replies: 0
    Last Post: 04-12-2016, 10:01 AM
  3. Is this a CMP Greek return '03?
    By LeagleEagle in forum M1903/1903A3/A4 Springfield Rifle
    Replies: 8
    Last Post: 02-22-2012, 12:46 PM
  4. Danish return...
    By coneten in forum M1 Garand/M14/M1A Rifles
    Replies: 15
    Last Post: 06-14-2010, 09:35 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts