+ Reply to Thread
Page 2 of 2 FirstFirst 1 2
Results 11 to 19 of 19

Thread: 1891 Argentine made in Germany won't fire

Click here to increase the font size Click here to reduce the font size
  1. #11
    Legacy Member AlaskanUser's Avatar
    Join Date
    Dec 2020
    Last On
    12-15-2020 @ 04:37 PM
    Location
    Alaska
    Posts
    8
    Local Date
    10-31-2024
    Local Time
    02:43 PM
    Thread Starter
    No slug, inside micrometer just to see if it was 6.something or 7.something. Tried to delete the whole message but it wouldn't so said disregard.

  2. # ADS
    Friends and Sponsors
    Join Date
    October 2006
    Location
    Milsurps.Com
    Posts
    All Threads
    A Collector's View - The SMLE Short Magazine Lee Enfield 1903-1989. It is 300 8.5x11 inch pages with 1,000+ photo’s, most in color, and each book is serial-numbered.  Covering the SMLE from 1903 to the end of production in India in 1989 it looks at how each model differs and manufacturer differences from a collecting point of view along with the major accessories that could be attached to the rifle. For the record this is not a moneymaker, I hope just to break even, eventually, at $80/book plus shipping.  In the USA shipping is $5.00 for media mail.  I will accept PayPal, Zelle, MO and good old checks (and cash if you want to stop by for a tour!).  CLICK BANNER to send me a PM for International pricing and shipping. Manufacturer of various vintage rifle scopes for the 1903 such as our M73G4 (reproduction of the Weaver 330C) and Malcolm 8X Gen II (Unertl reproduction). Several of our scopes are used in the CMP Vintage Sniper competition on top of 1903 rifles. Brian Dick ... BDL Ltd. - Specializing in British and Commonwealth weapons Specializing in premium ammunition and reloading components. Your source for the finest in High Power Competition Gear. Here at T-bones Shipwrighting we specialise in vintage service rifle: re-barrelling, bedding, repairs, modifications and accurizing. We also provide importation services for firearms, parts and weapons, for both private or commercial businesses.
     

  3. #12
    Legacy Member AlaskanUser's Avatar
    Join Date
    Dec 2020
    Last On
    12-15-2020 @ 04:37 PM
    Location
    Alaska
    Posts
    8
    Local Date
    10-31-2024
    Local Time
    02:43 PM
    Thread Starter

    Still no go

    Assembled bolt as properly as possible. Firing pin protrusion within correct range, cocking piece flush with end of firing pin... I assume this meant firing pin end flush with the back part of the cocking piece hole furthest to the rear. Not even a dent in the primer.
    I'll order the chamber casting stuff from Brownell's in an order I need to place.. I'll slug the barrel later and mic that.
    Some of the literature I've read and videos I've watched suggest using a nickle or a quarter to keep some spacing so you can disassemble the bolt. I have to use the end of a 1/4" brass drift to get the spacing needed to rotate the bolt off. Does this mean anything to anyone?

  4. Avoid Ads - Become a Contributing Member - Click HERE
  5. #13
    Legacy Member vintage hunter's Avatar
    Join Date
    Dec 2010
    Last On
    @
    Location
    S.C.
    Age
    56
    Posts
    1,680
    Local Date
    10-31-2024
    Local Time
    07:43 PM
    Quote Originally Posted by AlaskanUser View Post
    Assembled bolt as properly as possible. Firing pin protrusion within correct range, cocking piece flush with end of firing pin... I assume this meant firing pin end flush with the back part of the cocking piece hole furthest to the rear. Not even a dent in the primer.
    I'll order the chamber casting stuff from Brownell's in an order I need to place.. I'll slug the barrel later and mic that.
    Some of the literature I've read and videos I've watched suggest using a nickle or a quarter to keep some spacing so you can disassemble the bolt. I have to use the end of a 1/4" brass drift to get the spacing needed to rotate the bolt off. Does this mean anything to anyone?
    Not sure I'm following the whole use pocket change to keep some spacing to disassemble the bolt thing.
    If you're referring to unscrewing the bolt shroud/fp assy. out of the bolt body just flip the safety tab to the center position(assuming it's a mil spec safety) before removing the bolt from the reciever. Doing this removes all the fp spring tension.
    If it's an aftermarket low pro safety clamp the cocking piece protrusion in a vise and pull out on the bolt body while turning it in the appropriate direction.
    Any way you can post pics of what you're working with? Namely the cartridge you're attempting to fire, especially there headstamp. Oh, what the hay, might as well post some of the whole rifle and the bolt assembled and disassembled while you at it.
    Last edited by vintage hunter; 12-07-2020 at 02:27 PM.

  6. #14
    Contributing Member Low & Slow's Avatar
    Join Date
    May 2015
    Last On
    Today @ 11:48 AM
    Location
    colorado usa
    Posts
    404
    Local Date
    10-31-2024
    Local Time
    05:43 PM
    If this violates any copyrights or what ever, please delete it forthwith. Not for personal gain, just trying to help shed some light.

  7. Thank You to Low & Slow For This Useful Post:


  8. #15
    Legacy Member vintage hunter's Avatar
    Join Date
    Dec 2010
    Last On
    @
    Location
    S.C.
    Age
    56
    Posts
    1,680
    Local Date
    10-31-2024
    Local Time
    07:43 PM
    Quote Originally Posted by Low & Slow View Post
    If this violates any copyrights or what ever, please delete it forthwith. Not for personal gain, just trying to help shed some light.
    Ah, right you are. It's been good many years since I last handled a '91 and I forgot they have 2 position safeties rather than the 3 position of the later models.

  9. #16
    Legacy Member AlaskanUser's Avatar
    Join Date
    Dec 2020
    Last On
    12-15-2020 @ 04:37 PM
    Location
    Alaska
    Posts
    8
    Local Date
    10-31-2024
    Local Time
    02:43 PM
    Thread Starter
    Every online and written PDF I have about this exact gun refers to the coin or spacer method, the bolt will not simply unscrew as it goes under the part that I unscrew it from. I've already written that I'm attempting to fire Model 1891 Argentineicon Mauser PPU 7.65 Argentinian Mauser ammo and no primer hit no matter how I set the bolt up. I've ordered some chamber casting stuff, haven't slugged the barrel yet but it inside mics to approx 7.6 something caliber.
    I have the three position selector flipped properly according to multiple different sources. I've become pretty good at disassembly and reassembly of the bolt and last adjusted the cocking piece hole to be flush with the end of the firing pin. I dunno. Will eventually get my Brownell's order, they are running slow to Alaska.. probably the Christmas time rush, and will eventually slug the barrel. Did people ever rechamber these to .308 and get away with the slightly smaller 7.62 bullet going down a 7.65 barrel? I'll try to get some pics after I get home from work late tonight or more likely tomorrow as I usually have a date with a wild turkey when I get home.
    George


    Quote Originally Posted by vintage hunter View Post
    Not sure I'm following the whole use pocket change to keep some spacing to disassemble the bolt thing.
    If you're referring to unscrewing the bolt shroud/fp assy. out of the bolt body just flip the safety tab to the center position(assuming it's a mil spec safety) before removing the bolt from the reciever. Doing this removes all the fp spring tension.
    If it's an aftermarket low pro safety clamp the cocking piece protrusion in a vise and pull out on the bolt body while turning it in the appropriate direction.
    Any way you can post pics of what you're working with? Namely the cartridge you're attempting to fire, especially there headstamp. Oh, what the hay, might as well post some of the whole rifle and the bolt assembled and disassembled while you at it.


    ---------- Post added at 03:52 PM ---------- Previous post was at 03:47 PM ----------

    Mine has a three position safety, at least it clicks into three positions and one of them prevents the firing pin from releasing.

    Quote Originally Posted by vintage hunter View Post
    Ah, right you are. It's been good many years since I last handled a '91 and I forgot they have 2 position safeties rather than the 3 position of the later models.

  10. #17
    Contributing Member Low & Slow's Avatar
    Join Date
    May 2015
    Last On
    Today @ 11:48 AM
    Location
    colorado usa
    Posts
    404
    Local Date
    10-31-2024
    Local Time
    05:43 PM
    Sounds like there is something funny going on here. The 1891 Argentineicon Mauser has a two position safety, and shouldn't need a 1/4" spacer to unscrew. I've got about 6 3/16" firing pin length here, very slight protrusion at the rear. Nickel is inserted for disassembly. Does this look like yours?

  11. #18
    Legacy Member vintage hunter's Avatar
    Join Date
    Dec 2010
    Last On
    @
    Location
    S.C.
    Age
    56
    Posts
    1,680
    Local Date
    10-31-2024
    Local Time
    07:43 PM
    Hmm, wondering if the OP's bolt is made up of mixed parts? Maybe a M'93/95 bolt shroud/firing pin assy screwed into an M '91 bolt body? If that's even possible...
    OP, does your bolt shroud have the Argentineicon "shaking hands" inspectors stamp on the left side like in the second pic above? It should be on the cocking piece and firing pin too, IIRC.
    Last edited by vintage hunter; 12-09-2020 at 05:36 AM.

  12. #19
    Legacy Member AlaskanUser's Avatar
    Join Date
    Dec 2020
    Last On
    12-15-2020 @ 04:37 PM
    Location
    Alaska
    Posts
    8
    Local Date
    10-31-2024
    Local Time
    02:43 PM
    Thread Starter
    I'll take it apart again and get pics and measurements when I get home tonight...

    Quote Originally Posted by Low & Slow View Post
    Sounds like there is something funny going on here. The 1891 Argentineicon Mauser has a two position safety, and shouldn't need a 1/4" spacer to unscrew. I've got about 6 3/16" firing pin length here, very slight protrusion at the rear. Nickel is inserted for disassembly. Does this look like yours?


    ---------- Post added at 10:36 AM ---------- Previous post was at 10:34 AM ----------

    Will post pics much later tonight or tomorrow. Thanks, guys. I'm pretty good with most guns but have zero experience with this one. Even if it's a bastardized assembly I really want to get it working for the memory of my Dad.

    Quote Originally Posted by vintage hunter View Post
    Hmm, wondering if the OP's bolt is made up of mixed parts? Maybe a M'93/95 bolt shroud/firing pin assy screwed into an M '91 bolt body? If that's even possible...
    OP, does your bolt shroud have the Argentine "shaking hands" inspectors stamp on the left side like in the second pic above? It should be on the cocking piece and firing pin too, IIRC.

+ Reply to Thread
Page 2 of 2 FirstFirst 1 2

Similar Threads

  1. 1891 Argentine Mauser
    By LouisianaJoe in forum Mauser Rifles
    Replies: 3
    Last Post: 04-12-2017, 01:35 AM
  2. 1891 Argentine Carbine
    By Ray P in forum Mauser Rifles
    Replies: 8
    Last Post: 02-13-2016, 10:10 AM
  3. 1891 Argentine bayonet
    By tlitt in forum Edged Weapons Forum
    Replies: 2
    Last Post: 02-23-2011, 10:49 AM
  4. 1891 Argentine Mauser
    By Treeman in forum Mauser Rifles
    Replies: 16
    Last Post: 12-01-2010, 09:11 PM
  5. 1891 Argentine
    By Barnettshale in forum Mauser Rifles
    Replies: 6
    Last Post: 01-24-2010, 03:17 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts