-
The things you do to keep out of mischief.....
Earlier today I was going through the saved photo's on my phone, deleting as many as possible to free up space. I found a few that I'd taken a couple of years ago during one of the lockdowns when I'd busied myself in the garage workshop. I thought they might be of interest to a few others just as nerdy as me. In the batch of ex-Indian No32's that I bought in 2016 were quite a few that came with brackets. Unfortunately four or five had either one or both of the cradle clamps missing, or in some cases, had had mis-matched top clamps forced onto them. I'd just left them to one side for several years, but as I had plenty of time on my hands & nowhere to go I decided to have a go at making some replacement clamps from scratch, using what tools I had available. A friend in Devizes very kindly put a one inch diameter drill down a length of mild steel rod that I'd bought, & then slit it lengthways to give me two lengths of steel channel like a gutter in section. I cut pieces from this as needed, & the rest I did largely using files & a pillar drill. A specially modified (ground) centre drill was used to create the holes with the correct angle of taper for the cradle screws. Anyway, all of the brackets seemed to turn out functional; one even was a very nice REL example.
And it kept me out of my wife's hair for a good few days during lockdown.....
Information
|
Warning: This is a relatively older thread This discussion is older than 360 days. Some information contained in it may no longer be current. |
|
Last edited by Roger Payne; 08-13-2023 at 05:44 AM.
Reason: clarification
-
The Following 24 Members Say Thank You to Roger Payne For This Useful Post:
30Three,
Alan de Enfield,
Atticus Thraxx,
blurrededge,
Brian Dick,
BurtonP,
CINDERS,
David TS,
desperatedan,
Flying10uk,
gravityfan,
Jonzie,
Lance,
Low & Slow,
MAC702,
MasterChief,
Ovidio,
rambo46,
Salt Flat,
Sapper740,
smle addict,
Strangely Brown,
Terrylee,
Warren
-
08-12-2023 04:08 PM
# ADS
Friends and Sponsors
-
Contributing Member
the rest I did largely using files
Yes it is possible to file to accurate sizes/dimensions but not many people seem to have the patience to learn how do so nowadays.
-
Thank You to Flying10uk For This Useful Post:
-
-
Advisory Panel
Peshawar or bust! Well done!
The conical countersinks and reliefs for the screw heads must have been pretty tricky? What did you do for those Roger?
Your copper file protectors are noted. Hang on, home-made soft jaws are they?
“There are invisible rulers who control the destinies of millions. It is not generally realized to what extent the words and actions of our most influential public men are dictated by shrewd persons operating behind the scenes.”
Edward Bernays, 1928
Much changes, much remains the same.
-
Thank You to Surpmil For This Useful Post:
-
Darra comes to Sutton Coldfield....!
The countersinks were drilled in the pillar drill using the specially reground centre drill. The reliefs an end mill.
Copper vice jaws (now worn out & well overdue replacement) .
-
-
Contributing Member
I see that you have my kind of bench, Roger, with plenty of stuff on it, in an "organised muddle". I know that some "engineers" would have a heart attack, preferring a spotless, polished bench with nothing on it.
I feel that manual skills are not valued today as much as they should be or use to be.
Last edited by Flying10uk; 08-13-2023 at 10:18 PM.
-
Thank You to Flying10uk For This Useful Post:
-
Contributing Member
It's not a muddle to the one using the area, my wife at times uses items from my shed I go in there to find a certain item at a certain place to find it missing.
This leads to questions of where did it go as it may not have moved for some years! I have always been taught put it back where you got it from.
As I said it's not chaos to the one who uses the stuff all the time.
Very nice work Roger it would have taken a fair while to get the meat off that piece of material and to then fine finish it to the correct tolerance.
Last edited by CINDERS; 08-14-2023 at 02:28 AM.
-
Thank You to CINDERS For This Useful Post:
-
F10UK, I have to hold my hand up to that one - the garage workshop is a muddle, & not even a particularly organised one. However, I do know where things are, at least most of the time! My wife has promised to treat me to a hobbyist mini milling machine if I tidy the place up, so now I have an incentive.............but it won't be the same!
Yes, Ron, it took ages to remove the meat by drilling multiple holes 'along' the cradle caps-to-be, then taking out the residual metal between the holes with a combination of a very coarse hand file & an electric rotary file. My own milling machine would have made life easier, although there was always going to be a fair amount of hand finishing.
-
Thank You to Roger Payne For This Useful Post:
-
Legacy Member
I havent been told to go to the shed for some time but i have been called to come out of the shed on a regular basis.
Great work Roger
-
Thank You to Bindi2 For This Useful Post:
-
Legacy Member
A friend in Devizes very kindly put a one inch diameter drill down a length of mild steel rod that I'd bought, & then slit it lengthways to give me two lengths of steel channel like a gutter in section.
Mr. S by any chance...?
Just the thing for putting round holes in square heads.
-
Thank You to GeeRam For This Useful Post:
-
Just might be......
-