-
FREE MEMBER
NO Posting or PM's Allowed
I have used the Turpentine/Boiled linseed oil mixed 50/50 for years and it works great. Give the stock a heavy coat and let it set about 30 minutes. Then wipe it down good with toweling. If the first attempt didn't remove all the crud, do it again. If you have heavy deposits of crud you may have rub these areas lightly with 4/0 steel wool after coating the stock with the 50/50. After the stock is cleaned, the 50/50 makes a good finish when applied in very light coats. Put a dab on an area and smooth it out until it will spread no farther, then move over and apply another dab.
-
02-14-2012 11:19 PM
# ADS
Friends and Sponsors
-
Believe it or not, for gentle cleaning, coating the stock in gasoline and letting it stand for a day or two, then buffing off will remove a LOT of crud without any impact to the original finish of the stock.
Союз нерушимый республик свободных Сплотила навеки Великая Русь. Да здравствует созданный волей народов Единый, могучий Советский Союз!
-
-
-
There is a product in Canada available at Loblaws Superstore and it is their house brand heavy duty liquid cleaner at $6.99 for a US gallon. This stuff works slicker than snot on a stick to remove: grease, oil, crud and anything else on the stock. I can take a beater, fireplace ready POS and it looks almost new after a good hot water bath and a couple of sprayings of the cleaner and some steaming to remove any dents. Missing wood you cannot create, but you can sure raise a dent. A coat of cabinet makers alcohol stain in a blended colour along with an hour or two of boning the stock and NO steel wool or sandpaper to be used, you will have a stock that almost looks like the day it was made.
-
-
FREE MEMBER
NO Posting or PM's Allowed
Originally Posted by
Warren
NO steel wool
Very fine steel/brass wool can be a great cleaner when used with linseed oil. It works well to clean off grit and grime. The steel/brass wool need to be very fine though, like 0000. Just my opinion.
mdrim13
-
FREE MEMBER
NO Posting or PM's Allowed
Is denatured alcohol suitable for old dirty stocks or is turpentine better ?
-
Legacy Member
I have had good success with Murphy's oil soap and warm water. The BLO/Turpentine works quite well also. Patience and perceverance seem to be the key. I lack the former loads of the latter.
-
-
FREE MEMBER
NO Posting or PM's Allowed
The idea that linseed oil does any good in the preservation or restoration of any wood finish is a total fallacy.
If a piece of wood has an obvious finish on it you should first identify what that finish is before doing any “cleaning”. Shellac, regardless of its’ age, is soluble in alcohol or ammonia. To test the surface locate a less obvious location and lightly wet your finger tip with some alcohol and tap with your finger on that location repeatedly while blowing on your finger. As the alcohol evaporates the surface will start to get sticky. If this happens then you know that it is shellac and go no further. If it is shellac do not use any potion, concoction, or the like that has either alcohol or ammonia in it. If the surface of the stock has grease, oil, or wax that you are trying to remove dampen, not soak, a soft cloth with mineral spirits and whip the surface until clean. Immediately after this cleaning, us a solution of water and a pure detergent (Orvus) at room temperature. Use very little of the Orvus as it is a concentrate. With another soft absorbent cloth wet the cloth with this solution and wring it out tight. Wipe the surface down with this cloth and dry with another soft cloth. When dry apply a good paste wax and buff.
This below information was found on the Web site of the American Institute for Conservation (AIC) AIC - The American Institute for Conservation “The American Institute for Conservation of Historic and Artistic Works (AIC) is the national membership organization of conservation professionals. Its members include conservators, educators, scientists, students, archivists, art historians, and other conservation enthusiasts in over twenty countries around the world.”
“It was once thought that furniture needed to be “fed” with various mixtures of oils and other materials to keep it from drying out. However, a better approach would be to keep furniture in a stable environment. Furniture oils are not recommended for maintenance as many of them contain linseed oil or other drying oils, and when used repeatedly will create a gummy, insoluble surface coating that darkens and obscures the grain of the wood. Other furniture polishes contain non-drying oils such as lemon oil, but attract and entrap dirt and grime. Silicone polishes are also not recommended as they leave a film that is difficult to remove and can interfere with future finish treatments.”
“The best maintenance for clear-varnished furniture is a coating of good paste wax. Wax is a very stable material that does not change chemically over time and provides protection from moisture and airborne pollutants. Good quality paste wax is available in most hardware stores. A thin coat applied following the directions on the can is all that is needed, no more than once a year.”
-
Contributing Member
-
-
FREE MEMBER
NO Posting or PM's Allowed
The stocks on firearms are often referred to as "furniture". Wood is wood regardless as to whether it is a chair, a boat, a house, or a gun stock it is still susceptible to the same physical changes due to environment changes as any other wooden object. The finish is there to protect the wood against environmental abnormalities.
The original posting was dealing with the preservation of the original finish that he had on his rifle. What has been mentioned here after were suggestions of using everything from Murphy’s Oil Soap to Simple green and OOOO steel or bronze wool, turpentine, alcohol and everything else in between. Many of these materials may be incompatible with the finish he may have on his rifle. Certainly, the abrasive materials suggested are distructive to the originality of the surface.
Below is an excerpt from an article from Wood Magazine June 1989 in which Ron Ashby, a professional woodworker, refinisher, and lecturer, along with Wallace Gusler, are quoted in the uses of paste wax and other products as they relate to wood and their finishes. If you are not familiar with Mr. Gusler and his work, he has held many positions at Colonial Williamsburg including Chief Conservator for Furniture and Arms, and Director of Conservation. He is also a renowned world class Master Gunsmith.
Wax Protection for Furniture
Despite the multitude of furniture care products that promise to "feed" or "polish" your fine furniture, Ashby believes high-quality furniture wax is the best choice. "All the other care products available attract dust with the residue they leave behind," he says. At Virginia's Colonial Williamsburg, Wallace Gusler, director of conservation, oversees the preservation of authentic colonial furniture. "Our primary concern with pieces that have an intact, original finish is conservation," he says. "For that, we use wax. And, Gusler believes, all wood furniture, not just historic pieces, deserves wax protection. "Everyone collects furniture to some extent, he notes, "But their collection happens to be their household furniture."
What about lemon oil, another popular wood-care product? Gusler says, "The value of oil to wood is folklore. Of course, oil gives a wood finish a superficial shine, but it isn't beneficial. In fact," he elaborates, "Commercial lemon oil has nothing to do with lemons. It's essentially kerosene, and can be harmful to a finish."
Then, there are aerosol spray cleaners and polishes that contain silicone. They may not harm the present finish, say Ashby and Gusler, but they will cause problems down the road if you contemplate refinishing. "Products with silicones are cheap, quick, and easy, but they don't protect," comments Ashby. "Besides, silicones make refinishing difficult because, even after stripping, a new finish won't adhere."
-
Contributing Member
-