Search:

Type: Posts; User: Madcap; Excluded Forums: Milsurp Knowledge Libraries (READ ONLY)

Page 1 of 5 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    120
    Views
    5,521

    Heat Shield Prototype No. II

    Finally got together with a friend early this afternoon to rout a groove in a 2x6. The idea is to press a 1" pipe down onto the flat that will be held centered with some nails both sides or whatever....
  2. Replies
    120
    Views
    5,521

    Only thanks to your interest and generosity could...

    Only thanks to your interest and generosity could it have gotten anywhere at this point. It was a bit intimidating for me to start on it without more tools but as it turns out I had all that was...
  3. Replies
    120
    Views
    5,521

    Really only thanks to your interest and...

    Really only thanks to your interest and generosity has this been anything at all. It's been interesting and a good learning experience for me and I'm looking forward to doing some refining when I can...
  4. Replies
    120
    Views
    5,521

    Heat Shield Added Details

    I realized how easy it could be to roll the rear edge and add the two dimples so I couldn't resist giving it a shot. A ball peen hammer and the steel pipe easily rolled the rear edge. I learned...
  5. Replies
    120
    Views
    5,521

    You may be correct. I thought I'd seen some that...

    You may be correct. I thought I'd seen some that were riveted but they may have been repros...
  6. Replies
    0
    Views
    227

    WTB: MODEL 97 RIOT GUN FRONT SLING SWIVEL Help

    Looking for an original Model 97 Riot Gun front sling swivel - thanks for any help.
  7. Replies
    120
    Views
    5,521

    Does anyone know what type rivets are used to...

    Does anyone know what type rivets are used to attach the shield.... brass or steel...?
  8. Replies
    120
    Views
    5,521

    Yes sir, and thanks to folks that help out along...

    Yes sir, and thanks to folks that help out along the way really means the most...

    Next attempt hopefully will be more sophisticated. I'd like to have the pipe cut in half and use it to make a...
  9. Replies
    120
    Views
    5,521

    Flat Heat Shield Prototype

    I finally decided to try bending one of the flats with just a hammer and a couple short lengths of steel pipe. It took some time and effort but it didn't turn out too bad.

    It needs some final...
  10. Replies
    4
    Views
    366

    I appreciate the help but after looking around on...

    I appreciate the help but after looking around on the net here and there and everywhere I'm going hold off and to try to find a compete receiver if possible. Hopefully one with an extension and - Ive...
  11. Replies
    120
    Views
    5,521

    His website is back up - I feel a bit of relief...

    His website is back up - I feel a bit of relief over that. Three months more to go for the adapter and shield...maybe less with some luck.
  12. Replies
    120
    Views
    5,521

    Let me know if he answers the phone....

    Let me know if he answers the phone....
  13. Replies
    120
    Views
    5,521

    Ahh, OK, I thought that might have been the case....

    Ahh, OK, I thought that might have been the case. Hope he intends to continue production since I've paid for an adapter a month ago.
  14. Replies
    6
    Views
    297

    I tried replying to this thread earlier and same...

    I tried replying to this thread earlier and same thing happened...

    edit: now it's OK
  15. Replies
    120
    Views
    5,521

    I received it on another thread I tried replying...

    I received it on another thread I tried replying to on another thread here on this site also...
    maybe my computer has a glitch. (Although this reply had no issue.)
  16. Replies
    6
    Views
    297

    I forgot to mention they might be for a...

    I forgot to mention they might be for a motorcycle - but they don't appear to be that very rugged of construction. The other military forum site mentions "Warning: Potential Security Risk Ahead" -...
  17. Replies
    120
    Views
    5,521

    I couldn't remember what east taylor recommended...

    I couldn't remember what east taylor recommended and right now the website is not accessible...don't understand but this is what shows up - "Warning: Potential Security Risk Ahead".....
  18. Replies
    6
    Views
    297

    US CANVAS SADDLE BAGS - Need ID Help

    These saddle bags are constructed of light weight cotton canvas that were acquired in 1974 while mustering out of the 19th Special Forces Group in Layton Utah. I thought they were interesting and the...
  19. Replies
    120
    Views
    5,521

    Prior to my orders East Taylor wasn't taking...

    Prior to my orders East Taylor wasn't taking orders but I kept checking for several days and apparently got lucky and was able to order both Model 12 and M97 adapters. The M12 was ordered March 2. ...
  20. Replies
    120
    Views
    5,521

    Yesterday I consulted with a long time friend and...

    Yesterday I consulted with a long time friend and former Australian Navy machinist and he gave me some 4130 pipe the same diameter as the M12 barrel. I hope to get it cut in half and make some...
  21. Replies
    120
    Views
    5,521

    Briefly checking in - nothing further to mention...

    Briefly checking in - nothing further to mention as this point on bending the flat heat shields. I haven't had much time to devote but hope to get back to it ASAP. I'm planning on visiting a couple...
  22. WTB: Win model 12, 12ga. Complete receiver and magazine

    Looking for a good M12 12Ga. receiver and magazine donor for M12 Riot gun barrel.... :help:

    Thanks ~
  23. Replies
    120
    Views
    5,521

    My original adapter fits flush with the end of my...

    My original adapter fits flush with the end of my barrel as it should for the M12. You may notice his barrel extends past the adapter for some reason like the M97.
    The dimples on his shield sit...
  24. Replies
    120
    Views
    5,521

    According to the East Taylor website page the...

    According to the East Taylor website page the Model 12 adapter is specifically made for the M12 commercial barrel due to it's narrower diameter but to be clear my friend said the M97 was a better fit...
  25. Replies
    120
    Views
    5,521

    My buddy originally had an East Taylor M12...

    My buddy originally had an East Taylor M12 adapter for his commercial Model 12 conversion but said fit loosely so chose the M97 instead. His conversion was done by a professional with the M97 adapter...
Results 1 to 25 of 101
Page 1 of 5 1 2 3 4
Quartermaster Stores