Search:

Type: Posts; User: chuckindenver; Excluded Forums: Milsurp Knowledge Libraries (READ ONLY)

Page 1 of 5 1 2 3 4

Search: Search took 0.11 seconds.

  1. Replies
    5
    Views
    221

    Remington? Smith Corona? or National Ord, Santa...

    Remington? Smith Corona? or National Ord, Santa Fe Arms?
  2. Replies
    6
    Views
    486

    crush. back it off , recrush , repeat until the...

    crush. back it off , recrush , repeat until the marks line up perfect... dont over think this.
  3. Replies
    8
    Views
    747

    heat the work, not the solder.... patience is...

    heat the work, not the solder.... patience is key. clean stainless wire brush to clean the surface.. good quality flux
  4. they need tapped , also, if you have repro...

    they need tapped , also,
    if you have repro screws, they are known to be over sized. iv found this a few times.
    soap works well, go in, turn out go in farther, turn out,, take your time
  5. Replies
    3
    Views
    478

    8 of 43

    8 of 43
  6. Replies
    20
    Views
    1,641

    rattle can, will likely come right off with...

    rattle can, will likely come right off with aircraft remover, I suspect recovered drill rifle. for sure worth bring back.. original parts can be had, but are pricey
  7. Replies
    6
    Views
    653

    partsgun, nice scope, scope value is more then...

    partsgun, nice scope, scope value is more then the gun. gun value? 1500 depending on the serial number range, scope value..? 3500 to 5000 depending on the buyer
  8. Replies
    13
    Views
    2,446

    non of the A3 barrel, {2 groove} or 1903...

    non of the A3 barrel, {2 groove} or 1903 springfield barrels grafted into a Garand barrel stub should ever be fired with live ammo.
    they will fail. not if, but when.
    and heres why.
    they cut a...
  9. Replies
    9
    Views
    593

    heavy sanded stock. springfield Mark1 cutoff...

    heavy sanded stock. springfield Mark1 cutoff spindle. Remington 1903, un marked barrel is suspect. buttplate is suspect. I would check the cal, of the rifle, before you fire it, I know 1903s are...
  10. Replies
    10
    Views
    872

    the spring that holds the band in place, will...

    the spring that holds the band in place, will have an R at the very end , facing out.
  11. stock is an original NRA sporter stock that...

    stock is an original NRA sporter stock that someone modified
  12. Replies
    10
    Views
    872

    yes....

    yes....
  13. Replies
    5
    Views
    1,334

    nice Remington. serial has nothing to do with...

    nice Remington. serial has nothing to do with heat treatment on the Remingtons. as all are safe to fire, lend lease as well. very nice score.
  14. Replies
    9
    Views
    1,131

    these were in the G.I. package when I got them

    these were in the G.I. package when I got them
  15. Replies
    9
    Views
    1,131

    104079

    104079
  16. I have that small booklet someplace.

    I have that small booklet someplace.
  17. Replies
    9
    Views
    1,131

    i have some, will have to look for them. they are...

    i have some, will have to look for them. they are still in a packasge
  18. Replies
    6
    Views
    1,084

    there is a seller on fleabay selling a large lot...

    there is a seller on fleabay selling a large lot of M1 stocks with these crisp or made to look worn markings on them. this is not and can not be any sort of A4 or A4 replica, its a Rock island...
  19. Replies
    6
    Views
    1,084

    rifle was made up from a sporterized hunting...

    rifle was made up from a sporterized hunting rifle. stock is a real C stock, markings are not genuine. those would be OK for a 43 Garand, but not on a 1903.
    value is the some of the parts....
  20. Replies
    9
    Views
    963

    hard to say for sure. without holding them. a...

    hard to say for sure. without holding them. a lot of better replicas are popping up lately being advertised as genuine.. they did do a few changes, steel was one of them, switched over to 8620...
  21. Replies
    9
    Views
    963

    bolt on the left, most likely, bolt on the right...

    bolt on the left, most likely, bolt on the right most likely not
  22. the picture, was just to show the step. and was...

    the picture, was just to show the step. and was a random photo off the net...
  23. 103269 you can see in the picture, the A3 rear...

    103269

    you can see in the picture, the A3 rear target sight has a step built in to clear the reverse dove tail
  24. the rear sight is made for a 1903 and not the...

    the rear sight is made for a 1903 and not the A3.. looks like its not straight. however. the A3 rear sight is different to clear the reverse dovetail.
  25. Replies
    1
    Views
    680

    R4 R6 bolts are a little longer at the bolt head....

    R4 R6 bolts are a little longer at the bolt head. some CC bolts are also longer. but they are hit and miss.
Results 1 to 25 of 120
Page 1 of 5 1 2 3 4
T-bones Shipwrighting