+ Reply to Thread
Page 1 of 2 1 2 LastLast
Results 1 to 10 of 11

Thread: Rubber washers on the barrel of a 03A3 RIA rebuild?

Click here to increase the font size Click here to reduce the font size
  1. #1
    Legacy Member Freestateguy's Avatar
    Join Date
    Nov 2021
    Last On
    03-10-2022 @ 11:30 PM
    Location
    Boise, ID
    Posts
    17
    Real Name
    Tim
    Local Date
    10-31-2024
    Local Time
    03:55 PM

    Rubber washers on the barrel of a 03A3 RIA rebuild?

    Hello
    I am cleaning up a CMPicon certified RA 1903a3 rifle with barrel date 8-43 that was rebuilt at RIA and noticed there are 3 rubber washers on the barrel after it was disassembled
    I didn't notice were they where placed but I assume under the upper band and possibly under the clips on the correct A3 handguard

    Ive never seen these before
    Does anyone have feedback on these?
    Maybe part of the rebuild process at Rock Island?
    Accurizing perhaps?
    Information
    Warning: This is a relatively older thread
    This discussion is older than 360 days. Some information contained in it may no longer be current.

  2. # ADS
    Friends and Sponsors
    Join Date
    October 2006
    Location
    Milsurps.Com
    Posts
    All Threads
    A Collector's View - The SMLE Short Magazine Lee Enfield 1903-1989. It is 300 8.5x11 inch pages with 1,000+ photo’s, most in color, and each book is serial-numbered.  Covering the SMLE from 1903 to the end of production in India in 1989 it looks at how each model differs and manufacturer differences from a collecting point of view along with the major accessories that could be attached to the rifle. For the record this is not a moneymaker, I hope just to break even, eventually, at $80/book plus shipping.  In the USA shipping is $5.00 for media mail.  I will accept PayPal, Zelle, MO and good old checks (and cash if you want to stop by for a tour!).  CLICK BANNER to send me a PM for International pricing and shipping. Manufacturer of various vintage rifle scopes for the 1903 such as our M73G4 (reproduction of the Weaver 330C) and Malcolm 8X Gen II (Unertl reproduction). Several of our scopes are used in the CMP Vintage Sniper competition on top of 1903 rifles. Brian Dick ... BDL Ltd. - Specializing in British and Commonwealth weapons Specializing in premium ammunition and reloading components. Your source for the finest in High Power Competition Gear. Here at T-bones Shipwrighting we specialise in vintage service rifle: re-barrelling, bedding, repairs, modifications and accurizing. We also provide importation services for firearms, parts and weapons, for both private or commercial businesses.
     

  3. #2
    Contributing Member ssgross's Avatar
    Join Date
    Jan 2020
    Last On
    Today @ 11:24 AM
    Location
    Virginia
    Posts
    1,612
    Local Date
    10-31-2024
    Local Time
    06:55 PM
    Quote Originally Posted by Freestateguy View Post
    Accurizing perhaps?
    I think this is the case. I have not seen a 1903 set up like this, but this and similar practice is common enough in an attempt to dampen barrel vibrations. For example, I have a No.4 Mk2 that was set up as a target rifle. A rectangular "pad" was placed in the forend midway. It felt almost like plumbers putty to the touch, but harder, and was molded to engage the barrel. Many have also played with notecards under the muzzle of 1903's to tune the perfect upward pressure from the forend. Depending on how thick the orings were, you can check the places where they would engage the wood of the forend to get an idea. Note to the trolls...mentioning such things does not mean I condone the practice or think it's necessary ...but if it works in a tired old rifle to keep it shooting in its original, worn out wood...who can argue?
    Last edited by ssgross; 11-22-2021 at 10:49 PM.

  4. Avoid Ads - Become a Contributing Member - Click HERE
  5. #3
    Legacy Member Freestateguy's Avatar
    Join Date
    Nov 2021
    Last On
    03-10-2022 @ 11:30 PM
    Location
    Boise, ID
    Posts
    17
    Real Name
    Tim
    Local Date
    10-31-2024
    Local Time
    03:55 PM
    Thread Starter
    Thanks ssgross
    Good insight and it makes sense
    I plan on looking for the wear mark`s upon reassembly
    T

  6. #4
    Contributing Member ssgross's Avatar
    Join Date
    Jan 2020
    Last On
    Today @ 11:24 AM
    Location
    Virginia
    Posts
    1,612
    Local Date
    10-31-2024
    Local Time
    06:55 PM
    Would love to see some pics.

  7. #5
    Contributing Member mmppres's Avatar
    Join Date
    Mar 2014
    Last On
    10-10-2024 @ 08:58 AM
    Location
    butler pa
    Age
    59
    Posts
    1,098
    Real Name
    mike
    Local Date
    10-31-2024
    Local Time
    06:55 PM
    never seen that before

  8. #6
    Legacy Member Freestateguy's Avatar
    Join Date
    Nov 2021
    Last On
    03-10-2022 @ 11:30 PM
    Location
    Boise, ID
    Posts
    17
    Real Name
    Tim
    Local Date
    10-31-2024
    Local Time
    03:55 PM
    Thread Starter
    Hi ssgross,
    I looked at my documentation and realized I bought this CMPicon rifle from a guy that used it for match shooting so I think these O Rings likely were installed by him. Plus, they are in good shape to be factory installed back in the day. Notice also this guy added some "glue" to the rear sight to lock them in.

  9. #7
    Contributing Member ssgross's Avatar
    Join Date
    Jan 2020
    Last On
    Today @ 11:24 AM
    Location
    Virginia
    Posts
    1,612
    Local Date
    10-31-2024
    Local Time
    06:55 PM
    Quote Originally Posted by Freestateguy View Post
    added some "glue" to the rear sight to lock them in.
    in the pic it looks like dried grease. your fingernail can tell the difference. I've never heard of using o-rings to dampen a barrel, but hey if it works better than a notecard or other shim...whatever.
    Last guy likely put in a lot of range time to figure out what position he liked those rings in. I don't think they that they would make any difference re vibrations unless they also contacted wood somewhere, play around with sliding them. Maybe they left an indentation in the wood, or rubbed a spot. You'll never know how or why, but it sure is fun to speculate
    Check the pins on the front sight base and blade to see if the finish is worn off its head from removing the sight or blade to slip the rings off. If not, then the barrel was removed or replaced to add the rings. Look up your serial date range and match to the barrel to get an idea whether or not the barrel is original to the rifle.
    https://www.remingtonsociety.org/190...rial-no-table/

  10. #8
    Legacy Member Freestateguy's Avatar
    Join Date
    Nov 2021
    Last On
    03-10-2022 @ 11:30 PM
    Location
    Boise, ID
    Posts
    17
    Real Name
    Tim
    Local Date
    10-31-2024
    Local Time
    03:55 PM
    Thread Starter
    Those 3 O Rings are quite elastic and can easily stretch enough to go over the receiver. I wish I had paid more attention to their location when I took it apart - I wasn't expecting to see them. One was pretty stretched. I'm thinking under the Upper Band and Hand guard Clip-
    I'll likely just cut them off-

    BTW the receiver serial dates to 5 -43 - Barrel date is 8-43 so it looks to be original
    Thanks for your input- Have a good Thanksgiving

  11. #9
    Legacy Member baltimoreed's Avatar
    Join Date
    Jun 2021
    Last On
    10-17-2024 @ 09:41 AM
    Location
    Aurora, NC
    Posts
    114
    Real Name
    Ed Evans
    Local Date
    10-31-2024
    Local Time
    06:55 PM
    Maybe to eliminate a handguard rattle? Look too small to do much on a ‘03 bbl’s harmonics.
    “Give’em hell, Pike.”

  12. #10
    Contributing Member ssgross's Avatar
    Join Date
    Jan 2020
    Last On
    Today @ 11:24 AM
    Location
    Virginia
    Posts
    1,612
    Local Date
    10-31-2024
    Local Time
    06:55 PM
    Quote Originally Posted by baltimoreed View Post
    Maybe to eliminate a handguard rattle?
    unless the handgaurd/forend has been altered to where it is too small at the bands, tightening the bands would keep it from rattling.
    In my experience there is typically very little room under the barrel of a properly fit 1903 stock. Except for the muzzle bed you can just slide a notecard under it. 2 notecards will bind. A rubber ring therefore should make firm contact between barrel and forend, and such contact certainly would affect vibrations.
    Only one way to find out if it works...shoot the rifle without, and then with the rings in different positions. I would guess the rings were placed around the muzzle end as a cheap and easy fix for creating upward pressure from the forend if it were lacking. there should be plenty of room above the barrel so the ring doesn't contact the top half of the upper band. There should be a noticeable gap there.

+ Reply to Thread
Page 1 of 2 1 2 LastLast

Similar Threads

  1. 03 barrel and 03 front sight base & blade on 03a3 rebuild?
    By rustygun in forum M1903/1903A3/A4 Springfield Rifle
    Replies: 5
    Last Post: 05-31-2021, 06:33 PM
  2. SC 1903A3 Rebuild Barrel Markings O.B.S.3
    By Winch61 in forum M1903/1903A3/A4 Springfield Rifle
    Replies: 11
    Last Post: 04-15-2020, 12:17 PM
  3. No4Mk1 Washers and Bushing
    By Berg83 in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 10
    Last Post: 04-30-2014, 01:55 AM
  4. Adventures with with breeching washers
    By boatbod in forum Gunsmithing for Old Milsurps
    Replies: 8
    Last Post: 01-14-2012, 01:55 PM
  5. Barrel washers/shims
    By Kev G in forum The Bren LMG (Light Machine Gun)
    Replies: 18
    Last Post: 01-07-2012, 06:33 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts