+ Reply to Thread
Page 1 of 2 1 2 LastLast
Results 1 to 10 of 12

Thread: Remove handguards without removing gas cylinder

Click here to increase the font size Click here to reduce the font size

Hybrid View

  1. #1
    Legacy Member Pittsburgher's Avatar
    Join Date
    May 2021
    Last On
    06-28-2021 @ 03:55 AM
    Location
    California
    Posts
    1
    Local Date
    10-31-2024
    Local Time
    03:48 PM

    Remove handguards without removing gas cylinder

    Is it possible to remove the handguards without removing the gas cylinder?

    I am thinking of this removal process:
    • Pry open the Rear Handguard
    • Band/Clip
    • Slide out the Rear Handguard
    • Slide over the Lower Band
    • Pull the Front Handguard back and up

    I would to inspect the metal under the handguards for rust (i spilled some water there a few times years ago cleaning corrosive salts out of the barrel).

    The gas cylinder is super tight, even with the special gas plug wrench and Gas Cylinder Wrench to prevent torquing the barrel. Then I read that a tight gas cylinder is good for accuracy and thought better of taking that out.

    It's probably fine since I used hot water when I did salt flushing, but I want to get some RemOil on the barrel surface anyways just for peace of mind.
    Information
    Warning: This is a relatively older thread
    This discussion is older than 360 days. Some information contained in it may no longer be current.

  2. #2
    Legacy Member tr63's Avatar
    Join Date
    Jan 2013
    Last On
    02-05-2022 @ 08:25 AM
    Location
    maine U.S.A.
    Posts
    404
    Real Name
    john senesy
    Local Date
    10-31-2024
    Local Time
    06:48 PM
    Wow are you kidding !!! You will do way more damage to the rifle .. Why can't you remove the gas cylinder the correct way ? There some thing very wrong if you can not take the gas plug out ! You need to take the gas plug and cylinder off to clean it of built up fouling .
    Last edited by tr63; 05-10-2021 at 03:12 PM.

  3. Avoid Ads - Become a Contributing Member - Click HERE
  4. #3
    Advisory Panel browningautorifle's Avatar
    Join Date
    Jul 2008
    Last On
    Today @ 12:45 PM
    Location
    Victoria BC
    Posts
    30,402
    Real Name
    Jim
    Local Date
    10-31-2024
    Local Time
    03:48 PM
    Strip the rifle the correct way the book shows or you'll be having serious trouble. http://photos.imageevent.com/badgerd...der/FM23_5.pdf
    Regards, Jim

  5. Thank You to browningautorifle For This Useful Post:


  6. #4
    Legacy Member RCS's Avatar
    Join Date
    Mar 2009
    Last On
    Today @ 04:39 PM
    Location
    USA
    Posts
    4,395
    Real Name
    Robert Seccombe
    Local Date
    10-31-2024
    Local Time
    05:48 PM
    take the rifle apart to so you don't clip or crack the hand guards.

    I do know for a fact that you can remove the firing pin from the rifle and put it back without disassembly using the M10 tool

  7. #5
    Contributing Member Singer B's Avatar
    Join Date
    Aug 2019
    Last On
    10-26-2024 @ 01:39 PM
    Location
    Desert Hot Springs, California
    Posts
    1,085
    Real Name
    Walt Meyer
    Local Date
    10-31-2024
    Local Time
    05:48 PM
    The rifle is designed to be field stripped, reassembled, and maintain its accuracy. Do it the right way. The great thing about guns is each one can only be disassembled and reassembled one way, or else they won't work. Plus, it's kind of fun going through the process and then knowing your M1icon is cleaned, lubed and ready for the next shooting session or some downtime in the safe.

  8. Thank You to Singer B For This Useful Post:


  9. #6
    Contributing Member Mark in Rochester's Avatar
    Join Date
    Mar 2009
    Last On
    Today @ 11:59 AM
    Location
    Rochester, New York
    Posts
    6,912
    Real Name
    Mark in Rochester
    Local Date
    10-31-2024
    Local Time
    06:48 PM
    I have a tool which can remove the rear handguard - but there is always a risk of splitting the rear of it or cracking the front tip of it under the middle band and almost impossible with a handguard up against the face of the receiver - A risk without a reward
    He is no fool who gives what he cannot keep to gain that which he cannot lose
    There are no great men, only great challenges that ordinary men are forced by circumstances to meet.

  10. Thank You to Mark in Rochester For This Useful Post:

    RCS

  11. #7
    Advisory Panel
    Rick B's Avatar
    Join Date
    Mar 2009
    Last On
    10-28-2024 @ 08:16 PM
    Location
    Hinckley, Ohio
    Posts
    504
    Real Name
    RICHARD BORECKY
    Local Date
    10-31-2024
    Local Time
    06:48 PM

  12. The Following 4 Members Say Thank You to Rick B For This Useful Post:


  13. #8
    Contributing Member Singer B's Avatar
    Join Date
    Aug 2019
    Last On
    10-26-2024 @ 01:39 PM
    Location
    Desert Hot Springs, California
    Posts
    1,085
    Real Name
    Walt Meyer
    Local Date
    10-31-2024
    Local Time
    05:48 PM
    Quote Originally Posted by Rick Bicon View Post
    Rick B
    Very cool, thanks!

  14. #9
    Contributing Member Bob Seijas's Avatar
    Join Date
    Mar 2009
    Last On
    Today @ 07:50 AM
    Location
    Montville, NJ and Delray Beach, FL
    Posts
    2,256
    Real Name
    Bob Seijas
    Local Date
    10-31-2024
    Local Time
    06:48 PM
    Wow, didn't think I could learn anything new about the M1icon... never say never!
    Real men measure once and cut.

  15. #10
    Advisory Panel browningautorifle's Avatar
    Join Date
    Jul 2008
    Last On
    Today @ 12:45 PM
    Location
    Victoria BC
    Posts
    30,402
    Real Name
    Jim
    Local Date
    10-31-2024
    Local Time
    03:48 PM
    Quote Originally Posted by Bob Seijasicon View Post
    never say never
    I only knew that because when I bought my LL back in '76 it had that tool in the butt. I had no internet or even FM to go to, just figure it out in the barracks on the weekend. I never understood people wanting to remove the center band and how the handguard would crack it otherwise, mine didn't. But then, I was careful because there were no replacement parts at the time.
    Regards, Jim

+ Reply to Thread
Page 1 of 2 1 2 LastLast

Similar Threads

  1. need to remove varnish?
    By clong1979 in forum M1903/1903A3/A4 Springfield Rifle
    Replies: 1
    Last Post: 01-31-2013, 05:22 PM
  2. How to remove the Magazine Cut-Off
    By Promo in forum M1903/1903A3/A4 Springfield Rifle
    Replies: 24
    Last Post: 01-19-2012, 08:41 PM
  3. To remove or not to remove rust on a luger
    By Mudhut in forum Other Military Service Pistols and Revolvers
    Replies: 23
    Last Post: 10-21-2011, 05:24 PM
  4. Removing rear handguards - two methods
    By Bob Womack in forum M1 Garand/M14/M1A Rifles
    Replies: 14
    Last Post: 03-25-2009, 06:15 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts