+ Reply to Thread
Results 1 to 3 of 3

Thread: Receiver dimension measurement

Click here to increase the font size Click here to reduce the font size

Hybrid View

  1. #1
    FREE MEMBER
    NO Posting or PM's Allowed
    apothegm's Avatar
    Join Date
    Jul 2009
    Last On
    11-09-2009 @ 12:06 PM
    Posts
    18
    Local Date
    05-03-2025
    Local Time
    01:59 PM

    Receiver dimension measurement

    There is some speculation that the serial number my M1icon has been removed. I will be taking it into the BTAF office sometime soon and would like to be able to give the agent some evidence that the area has or has not been tampered with.

    Would someone with a micrometer be willing to mic the indicated area on one of the carbines in their collection?

    If the grinding was deep enough to obliterate the serial number, the measurement on mine should be considerably less than on an unaltered piece.

    http://picasaweb.google.com/PeteLuckel/Hold#

    * Or better yet - dimension from a factory blue print
    Information
    Warning: This is a relatively older thread
    This discussion is older than 360 days. Some information contained in it may no longer be current.
    Last edited by apothegm; 07-15-2009 at 02:52 PM. Reason: Additional thought

  2. #2
    FREE MEMBER
    NO Posting or PM's Allowed
    apothegm's Avatar
    Join Date
    Jul 2009
    Last On
    11-09-2009 @ 12:06 PM
    Posts
    18
    Local Date
    05-03-2025
    Local Time
    01:59 PM
    Thread Starter
    Never mind! BrianQ sent me pictures that settle the question.

  3. Avoid Ads - Become a Contributing Member - Click HERE
  4. #3
    FREE MEMBER
    NO Posting or PM's Allowed
    landtrain's Avatar
    Join Date
    Mar 2009
    Last On
    10-12-2009 @ 02:32 PM
    Posts
    43
    Local Date
    05-03-2025
    Local Time
    02:59 PM

    Measurements

    If you feel you must meet and greet BATF&E, Schedule your visit for 31 Otober, 3507. If it is a USGI Carbine it left the factory with a serial number. If it has a manufacturer it has a serial number. If the, original number was ground off it can be replaced just as easily. If it is NOT a USGI Carbine then it must be one of aproximately 45 makers or copy cat Carbines. Some of these were made without serial numbers. Perhaps yours is a commercial Carbine without a serial number. If you feel that your Carbine must have a serial number, take any 7 digit number between zero and 8069661 and add an "X" prefix. PS: Make sure your Carbine is marked 'M1icon' and not 'M2' or M1 with a 2 over stamped. GCAicon-68 spends paragraphgs on serial numbers and who should have what. I was in Germanyicon when GCA-68 became law. I was told by ATF (?) to stamp any firearm that I owned sans serial number to stamp it with my army serial number. (Pre, SSN.) I have a total of 7 long guns all with the same serial number, one of which is a Saginaw S'G'. Do not involve ATF until you are completly out of options. Any good machine shop can anneal the receiver and stamp it with a number. GOOD LUCK.

+ Reply to Thread

Similar Threads

  1. M14 Receiver?
    By BeauMiller in forum M1 Garand/M14/M1A Rifles
    Replies: 24
    Last Post: 10-15-2009, 08:11 PM
  2. receiver repair OT
    By Chuckindenver in forum M1903/1903A3/A4 Springfield Rifle
    Replies: 7
    Last Post: 04-02-2009, 11:03 AM
  3. Need M1 Receiver
    By sdh1911 in forum Milsurps General Discussion Forum
    Replies: 6
    Last Post: 04-10-2008, 05:46 PM
  4. m44 hex receiver
    By sdh1911 in forum Milsurps General Discussion Forum
    Replies: 13
    Last Post: 03-24-2007, 09:35 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts