+ Reply to Thread
Results 1 to 3 of 3

Thread: cleaner, rifle bore(CR)

Click here to increase the font size Click here to reduce the font size

Hybrid View

  1. #1
    FREE MEMBER
    NO Posting or PM's Allowed
    phil evans's Avatar
    Join Date
    Mar 2009
    Last On
    11-07-2016 @ 04:24 PM
    Location
    austin, texas
    Posts
    17
    Local Date
    06-10-2025
    Local Time
    09:34 PM

    cleaner, rifle bore(CR)

    i have a open top plywood case of cardboard separated ~25 cans of
    2 ounce
    cleaner, rifle bore (cr)
    spec. jan. c-372
    stock No. 51.c-1313-392
    cont. da-28.024
    ord. 2145 52)
    george senn, inc.
    phila., pa

    given to me ~1963.
    is this bore cleaner ok to use.
    will it remove copper from CMPicon greek rounds?
    it is oily, will it suffice to use as a cleaner and lubricant.
    thanks.
    Information
    Warning: This is a relatively older thread
    This discussion is older than 360 days. Some information contained in it may no longer be current.

  2. #2
    FREE MEMBER
    NO Posting or PM's Allowed
    Ben Hartley's Avatar
    Join Date
    Mar 2009
    Last On
    03-04-2015 @ 11:56 AM
    Location
    Jaffrey, New Hampshire
    Age
    86
    Posts
    85
    Local Date
    06-10-2025
    Local Time
    08:34 PM

    Bore Cleaner

    Phil...

    Most probably OK for use, though I'd be very cautious about leaving it in the bore. In the dark ages, one used bore cleaner for that, only. that is, to get the bore clean; one used the proverbial "light coat of oil" to preserve the bore.

    HTH

    Ben Hartley

  3. #3
    FREE MEMBER
    NO Posting or PM's Allowed
    slamfire1's Avatar
    Join Date
    Mar 2009
    Last On
    11-19-2017 @ 10:00 PM
    Posts
    135
    Local Date
    06-10-2025
    Local Time
    08:34 PM
    Mil C -372 Rifle Bore cleaner is excellent stuff. You cannot find the spec on Dodiss anymore, but I pulled it and read it.

    Mil C-372 is a powder solvent. It was also tested to remove corrosive primer residue. It will also provide some rust protection, but it is in the same class of rust provention as a light oil.

    I used it as a corrosive primer solvent, put the rifle aways for weeks. Came back and found rust in the barrel. That was the last time I relied on the stuff for removal of corrosive residue. I use the stuff to remove powder residue, then I use hot water. Never had a barrel rust after the hot water treatment.

    It is not a lubricant. You cannot find a more cost effective lubricant than motor oil. It is also hard to find a better lubricant than motor oil.

    It will not remove copper. It will not remove lead. It is a powder solvent.

    I purchased four gallons of RBC at a Flea market. Five dollars a gallon. I am down to two gallons. I use it every time I clean a revolver, rifle, shotgun. I wipe all metal surfaces to remove powder fouling, then I wipe it off and leave oil. Or RIG grease for long term storage.

    Your stuff from the 60's, just use it. I used a quart can from 1964. Worked fine.

+ Reply to Thread

Similar Threads

  1. 577/450 and 577 Snider bore variations.
    By Nate in forum Martini Henry Rifles
    Replies: 6
    Last Post: 07-05-2009, 12:20 PM
  2. Strongest Cleaner to remove cosmoling but not hurt Finish
    By gerry in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 6
    Last Post: 06-26-2009, 01:22 PM
  3. old cleaner-riflebore GI issue question
    By duggaboy in forum M1903/1903A3/A4 Springfield Rifle
    Replies: 6
    Last Post: 05-02-2009, 07:44 AM
  4. Sudden Hemorrhage takes can of WW-2 Bore Cleaner
    By Griff Murphey in forum M1 Garand/M14/M1A Rifles
    Replies: 1
    Last Post: 04-05-2009, 06:54 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts