+ Reply to Thread
Results 1 to 9 of 9

Thread: Ccnl #346

Click here to increase the font size Click here to reduce the font size

Hybrid View

  1. #1
    Legacy Member Garandrew's Avatar
    Join Date
    Mar 2009
    Last On
    03-19-2025 @ 11:10 PM
    Location
    Conn.
    Posts
    756
    Real Name
    Andy Gordon
    Local Date
    06-18-2025
    Local Time
    03:02 AM

    Ccnl #346

    Going by this information, all 3 of these cylinders are B&P Motor Sales, not Brown-Lipe-Chapin?



    Note my M1A1icon SN 592534, barrel date 8-43 has the 3 on top of the barrel

    Operating slide spring hole, bored all the way through, for drainage, started at SN 540,000

    Note sideways "1" on bolt lug near "OI"

    Is this Worcester taper pin?
    Information
    Warning: This is a relatively older thread
    This discussion is older than 360 days. Some information contained in it may no longer be current.

  2. Thank You to Garandrew For This Useful Post:


  3. #2
    FREE MEMBER
    NO Posting or PM's Allowed
    Newscotlander's Avatar
    Join Date
    Mar 2009
    Last On
    11-21-2019 @ 08:29 PM
    Location
    NY, ruled by the tyrant, Andrew Cuomo - the least freest, highest taxed, most corrupt state in Union
    Posts
    199
    Local Date
    06-18-2025
    Local Time
    02:02 AM
    Brown-Lipe-Chapin did not make gas cylinders. It almost certain that B-L-C shipped barrels to Inland without the gas cylinders installed.

  4. #3
    Legacy Member Garandrew's Avatar
    Join Date
    Mar 2009
    Last On
    03-19-2025 @ 11:10 PM
    Location
    Conn.
    Posts
    756
    Real Name
    Andy Gordon
    Local Date
    06-18-2025
    Local Time
    03:02 AM
    Thread Starter
    Well Chris what does the BI stand for in the pics above? Is it part of the barrel, or gas cylinder? How can you determine the barrel manufacturer? Inland or BLC? If the BI is a gas cylinder marking?
    Last edited by Garandrew; 12-27-2010 at 01:17 PM.

  5. #4
    Legacy Member Garandrew's Avatar
    Join Date
    Mar 2009
    Last On
    03-19-2025 @ 11:10 PM
    Location
    Conn.
    Posts
    756
    Real Name
    Andy Gordon
    Local Date
    06-18-2025
    Local Time
    03:02 AM
    Thread Starter
    All I see is Inland inspector marks on bottom flat of barrel, no BI, so must be Inland barrels?

  6. #5
    FREE MEMBER
    NO Posting or PM's Allowed
    Newscotlander's Avatar
    Join Date
    Mar 2009
    Last On
    11-21-2019 @ 08:29 PM
    Location
    NY, ruled by the tyrant, Andrew Cuomo - the least freest, highest taxed, most corrupt state in Union
    Posts
    199
    Local Date
    06-18-2025
    Local Time
    02:02 AM
    The BI is clearly stamped on the gas cylinder, which is swaged onto the barrel. Don't you have NL 346? All your questions are answered in that newsletter.

  7. #6
    Legacy Member BrianQ's Avatar
    Join Date
    Mar 2009
    Last On
    08-21-2022 @ 04:50 PM
    Posts
    466
    Local Date
    06-18-2025
    Local Time
    03:02 AM
    The gas cylinder was made by B & P Motor Sales Company (page 6 of NL 346). B-L-C barrels have BI on the barrel flat, Inland made have hieroglyphics in the same location.

  8. #7
    Legacy Member Garandrew's Avatar
    Join Date
    Mar 2009
    Last On
    03-19-2025 @ 11:10 PM
    Location
    Conn.
    Posts
    756
    Real Name
    Andy Gordon
    Local Date
    06-18-2025
    Local Time
    03:02 AM
    Thread Starter
    Yes, I just figured that out from newsletter 346..it was confusing me at first.
    I guess all my barrels are *Inland", as theres nothing else below the flat, except symbols

  9. #8
    Advisory Panel
    painter777's Avatar
    Join Date
    Mar 2009
    Last On
    @
    Location
    Central Michigan
    Posts
    5,499
    Local Date
    06-18-2025
    Local Time
    03:02 AM
    Inland 5,061,238
    Gas cylinder marked BI (?)
    Barrel Flat shows Inland made barrel (3-44)





    Inland 5,093,6XX
    Barrel dated 2-44, barrel flat marked BI, made by B-L-C, Brown-Lipe-Chapin Division on GMC.


    I don't have the 2-44 Inland here to compare. But the Inland barrel markings and date look to line up a bit different on the BI-B L C made barrel. I have no access to pictures of the gas cylinder on the 5,093xxx.

    FWIW,
    Charlie-painter777

  10. #9
    Legacy Member Garandrew's Avatar
    Join Date
    Mar 2009
    Last On
    03-19-2025 @ 11:10 PM
    Location
    Conn.
    Posts
    756
    Real Name
    Andy Gordon
    Local Date
    06-18-2025
    Local Time
    03:02 AM
    Thread Starter
    Excellant Charlie, I dont have any BI marked barrels, just the GeMo-Gryphics..[my term]

+ Reply to Thread

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts