carbine stocks different

[goo]

.. the rifle won't go in the one with the short inletting. were they issued that way and meant to be trimmed?
...
thx,
goo

Information

Warning: This is a relatively older thread This discussion is older than 360 days. Some information contained in it may no longer be current.

[BrianQ]

No

The difference between a short barrel channel and a long one is 1".

[Harlan (Deceased)]

.. the rifle won't go in the one with the short inletting. were they issued that way and meant to be trimmed?
...
thx,
goo

Goo,
Is the short channel a USGI stock or an aftermarket?

When you say it won't fit, do you mean it binds just as it's almost seated?
You may not be settling the action under the recoil plate correctly. Not really enough info to go on so far.

If you can give a little more info of what you are experiencing or what you are trying to do, someone will be able to help you here.

Good luck
~ Harlan

[Bubba-7]

Oh grasshopper,
The trigger housing pin is loose and when you put in the top stock it has backed out a little and it hits the inside wood. See the new chip showing in top stock your picture.

[Harlan (Deceased)]

Oh grasshopper,
The trigger housing pin is loose and when you put in the top stock it has backed out a little and it hits the inside wood. See the new chip showing in top stock your picture.

Good catch! You do well for a 'bubba'

[goo]

the channel is too short to accept the rifle. i would have to lengethen the channel to install the rifle. its not a trigger housing problem. it goes into other stocks just fine.
my question is what kind of rifle was the short chaneled stock built for?doesn't seem to be a usgi m1 carbine.

[Bubba-7]

The length of the channel has nothing to do with whether the metal goes in or not. As long as the stock was made to GI specks. If you have checked the trigger housing "PIN" to be sure it has not slipped out a little and hitting the inside of the stock, the metal will go in the stock. The only other reason I can think of is the barrel is not screwed in all the was so the distance from the receiver to the gas housing is long.
I had the same problem years ago and caught the pin coming out. It was so loose it would slide in a out as I placed the metal into the stock. And my stock was chipped just like your top picture.

[Harlan (Deceased)]

Goo,

You said at the end of your last post,
"It doesn't seem to be a usgi m1 carbine".

Just for clarification, did you mean it doesn't seem to be a USGI carbine stock?
If it's an aftermarket stock maybe it is out of spec.

[goo]

i figured it out. i'm basically just stupid (its a usmc thing).
...
Fifty-One Days!
A bartender is sitting behind the bar on a typical day, when the door bursts open and in come four exuberant Marines. They come to the bar and order five bottles of beer and ten glasses. They take their order over and sit down at the large table. The caps are popped, the glasses are filled and they begin toasting and chanting, "51 days, 51, days, 51 days!"

Two more Marines show up and soon their voices are joined in raising the roof, "51 days, 51 days, 51 days!!"

Finally the tenth Marine comes in with a picture under his arm, he walks over to the table, and sets the picture in the middle and the table erupts. Up jump the others, they begin dancing around the table, exchanging high-fives, all the while chanting, "51 days, 51 days, 51 days!"

The bartender can't contain his curiosity any longer, so he walks over to the table. There in the center is a beautifully framed child's puzzle of the cookie monster. When the frenzy dies down a little bit the bartender asks one of the Marines, "What's all the chanting and celebration about?"

The Marine who brought the picture pipes in, "Everyone thinks that Marines are dumb and they make fun of us. So, we decided to set the record straight. Ten of us got together, bought this puzzle and put it together. The side of the box said 2-4 years, but we put it together in 51 day."

[Bruce McAskill]

Goo are you sure that's a stock for a USGI carbine and not a Universal?