Stocking a no4 mk2 for target shooting 300, 500 and 600m
It appears that you are you're enjoying our Military Surplus Collectors Forums, but haven't created an account yet. As an unregistered guest, your are unable to post and are limited to the amount of viewing time you will receive, so why not take a minute to Register for your own free account now? As a member you get free access to our forums and knowledge libraries, plus the ability to post your own messages and communicate directly with other members. So, if you'd like to join our community, please CLICK HERE to Register !
Already a member? Login at the top right corner of this page to stop seeing this message.
Stocking a no4 mk2 for target shooting 300, 500 and 600m
Im busy digging through this site...Lots of good info but sometimes its a bit confusing.
I want to setup my gun to shoot at the above ranges, there seems to be at least 3 different ways. Does anyone have a suggestion as the one thats most likely too best suit the 500 and 600m ranges?
Im also curious on something else, is there a definitive piece of work on how a no4 mk1 (T) was stocked? ie was more work was done to its stock/wood than an "as issued" rifle and if so what? Its probably me but I cant seem to find something authoritive. Whatever the exact setup this would seem to be the benchmark that other mods were set against.
Information
Warning: This is a relatively older thread This discussion is older than 360 days. Some information contained in it may no longer be current.
I'll let you into a little secret SSJ. After the war, there was a series of trials to see what would be the optimum fitting of the fore-end for sniper rifles. And guess what.....? NONE of the other methods used, offered or tried during the trial EVER out performed a properly stocked up No4T. So if you want my simple but honest opinion, guess what I'll be saying.
Fuurther to that. There were several relaxations to the fitting of fore-ends to allow for shortages and the lack of good wood etc etc but these relaxations were NEVER allowed for the No4T. And I say that if it's good and accurate enough for a sniper who really NEEDS a good and accurate rifle, then it's good enough for a target shooter.
Sounds like the book Im reading. Though I still have not found the "T" method, (or maybe im blind to it in front of me) which yes is probably going to be good enough, certainly for my humble shooting talents.
The EMER/MoD method of fore-end fitting has been written here somewhere and been discussed until the cows come home. You'll just need to trawl through the forum until it crops up
i tryed middle bedding, center bedding. But none of these methods is better than military barrel bedding . If you're lucky one barrel bedding pattern leads to the same - good- results. Middle bedding and center bedding would be user friendly if you use a sling to shoot, a very tensioned sling. Because i shoot from a front rest i prefer to use military bedding obtaining good accuracy. But military bedding is good if you use a sling also. So...do not deviate from kosher.
For 2 years a tested on range with the same round different barrel bedding. Today 2 years means " the Infinity" ... but think: No.4 rifle has been produced in millions , many armourers tried, examineted and shot it. In different Countries. Probably they gained much experience in 20 years service than now today we could gain testing our rifle at our local range. So, do not deviate from approved bedding method as a rule of thumb.
The muzzle must contact the wood 2 " at least, and a weight of 3 to 7 pounds is required to free the muzzle from the fore end.
You can simply test it. First disassemble the rifle and put a paper sheet where muzzle - fore end contact will be, two inch behind- and let the paper sheet in place. Then reassemble the rifle paying attention paper sheet rests on the same place you located it.
After that test the weight required to free the paper sheet forced betweeen barrel and fore end. To do that you could use a fishing scale or different , weight known bottles secured to the muzzle. When paper sheet is free from contact read the weight. It must be between 3 and 7 pounds.
Watch these videos, there's the first one:
Before interesting about barrel bedding, start understanding wrist/ fore end contact, draws bearing and reparing, main screw and collar, knox form( or chamber area, it's the same). You could have a perfect bedded barrel rifle, but a poor shooter, if you do not check , understand and repair the above mentioned points.
Thanks bow (el al), and yes I have to sus all the above. My "new" (un-issued) forend arrived yesterday, so I have to follow Peter's howto to fit it, though first I have to "FTR" it from a no4 mk1 to a no4 mk1/2. I didnt want to simply start in case info had been superceeded.
Parashooter yes peter's doc is what's on my woodwork bench next to the gun and new stock.
but sometimes its a bit confusing.
Register To Reply
