-
Legacy Member
I've seen threads on other forums where individuals pull bullets, dump powder and put the primed case over a non-galvanized nail, fire the primer with a hammer and punch and then watch the nail for rust. Actually about to try this with a big lot of Chinese 7.62x54 I've purchased (goggles and earmuffs, of course). When shooting corrosive I've found it handy at the range to put a few inches of water in the bottom of a bucket and, with a cleaning rod, pull wet patches up to the chamber a few times with the tip of barrel dipped in the water. Fast and neat.
Ridolpho
-
The Following 4 Members Say Thank You to Ridolpho For This Useful Post:
-
04-24-2015 05:35 PM
# ADS
Friends and Sponsors
-
Advisory Panel
If I'm in doubt, I just used freshly primed cases and be done with it.
-
-
-
Legacy Member
Firing old surplus ammo is like owning a British sports car. Endless work once used.
Why use a 50 pound bomb when a 500 pound bomb will do?
-
The Following 4 Members Say Thank You to enfield303t For This Useful Post:
-
Legacy Member
Originally Posted by
Ridolpho
few inches of water in the bottom of a bucket and, with a cleaning rod, pull wet patches up to the chamber a few times with the tip of barrel dipped in the water. Fast and neat.
And all this time,,,,. Now I can chuck the funnel with fuel line shoved on it.
-
-
Legacy Member
Attachment 62272
I thought you do them with the dishes.
-
The Following 2 Members Say Thank You to Vincent For This Useful Post:
-
Advisory Panel
Like the guy that put his M14 in the dishwasher...?
-
-
Legacy Member
I bet it flash rusted when he opened the door........... I am not saying how I know that's what happens.
Attachment 62274
Windex?
-
-
Legacy Member
When I was shooting a lot of Black Powder revolver, the routine was to use spray "lube" at the range and head for home.
There, the guns would be stripped (usually one at a time) and immersed in HOT soapy water in the stainless-steel kitchen sink. (This was a bachelor pad at the time, as you may have guessed).
A good work-over with bore brushes and a toothbrush ensued, followed by a boiling water rinse.
Then a quick shake to remove most of the water and a blast with the hot-air gun (paint-stripper grade).
Thoroughly sprayed with one of the "Teflon" lubes, reassembled and put away, usually still warm. There was a Beatles song about that, as I recall.......
And these were STAINLESS BP revolvers.
"Blued" guns could be done in a similar fashion, but you had to be a bit quicker in the "rinse, dry, oil" phase or rust was a real possibility, especially here in a soggy, steamy Queensland summer .
I used to then simply "de-oil" (Carby cleaner), the cylinder / nipple assembly interiors before firing, to avoid contamination of the caps or powder.
-
-
Legacy Member
If you have a laundry tub at home, with a threaded spigot: Use an old washing machine hose. Cut the fitting off one end and attach with a clamp a 4" length of copper line that can be bent at a right angle. Thread the uncut end of the hose onto the spigot and turn on the hot water until it's really hot. Turn it off. Run a soapy patch through the bore. Then stick the spigot through the ejection port into the chamber of the rifle, with the muzzle in the tub. Turn the water back on, and let it run until the muzzle is too hot to touch. Turn off the water, run a dry patch through the bore, and oil immediately.
It's worked for me.
M
-
-
FREE MEMBER
NO Posting or PM's Allowed
Re. cleaning BP revolvers;
When I suggested water for removing fouling from his BP revolver, (it had gone rusty as put away dirty, ) this bloke immediately got up, filled the sink with water,.........and chucked it in! wood grips and all.
"Um,..Not Exactly like that" I said. :-)
MG Mike,
The copper pipe is a good idea!