+ Reply to Thread
Results 1 to 4 of 4

Thread: How to clean/patch pakerized finish on 30-06 FN Mauser

Click here to increase the font size Click here to reduce the font size
  1. #1
    Legacy Member DeeBee's Avatar
    Join Date
    Nov 2019
    Last On
    08-20-2021 @ 06:25 PM
    Location
    Victoria, Oz
    Posts
    16
    Local Date
    11-01-2024
    Local Time
    09:32 AM

    How to clean/patch pakerized finish on 30-06 FN Mauser

    Hi all,

    I have a slightly beat up FN Mauser in 30-06.

    The top of the barrel end near the receiver has been ground off where a crest is in some other examples I've seen.
    It has a dull silver like finish with blotchy rust stains. The butt plate has evenly succumbed to rust.
    The wood & metal fittings on it are a bit rattlely.
    For all this, it shoots alright.

    From this I assume that it might be one of these Naval parkerized Mausers that I've heard about.

    My questions are:

    Is there a simple way to at least ensure the preservation of the blotchy metal parts, maybe even clean it to a less distressed finish?
    I'm not overly keen to polish or remove the finish, as I've no idea how to replate it.

    Was the butt plate likely to have been pakerized? What might be a good rust removal and preservation method? I'm leaning toward "OOOO" steel wool until the rust is removed and an oil coating to preserve.

    Cheers,

    DeeBee
    Information
    Warning: This is a relatively older thread
    This discussion is older than 360 days. Some information contained in it may no longer be current.

  2. # ADS
    Friends and Sponsors
    Join Date
    October 2006
    Location
    Milsurps.Com
    Posts
    All Threads
    A Collector's View - The SMLE Short Magazine Lee Enfield 1903-1989. It is 300 8.5x11 inch pages with 1,000+ photo’s, most in color, and each book is serial-numbered.  Covering the SMLE from 1903 to the end of production in India in 1989 it looks at how each model differs and manufacturer differences from a collecting point of view along with the major accessories that could be attached to the rifle. For the record this is not a moneymaker, I hope just to break even, eventually, at $80/book plus shipping.  In the USA shipping is $5.00 for media mail.  I will accept PayPal, Zelle, MO and good old checks (and cash if you want to stop by for a tour!).  CLICK BANNER to send me a PM for International pricing and shipping. Manufacturer of various vintage rifle scopes for the 1903 such as our M73G4 (reproduction of the Weaver 330C) and Malcolm 8X Gen II (Unertl reproduction). Several of our scopes are used in the CMP Vintage Sniper competition on top of 1903 rifles. Brian Dick ... BDL Ltd. - Specializing in British and Commonwealth weapons Specializing in premium ammunition and reloading components. Your source for the finest in High Power Competition Gear. Here at T-bones Shipwrighting we specialise in vintage service rifle: re-barrelling, bedding, repairs, modifications and accurizing. We also provide importation services for firearms, parts and weapons, for both private or commercial businesses.
     

  3. #2
    Advisory Panel Patrick Chadwick's Avatar
    Join Date
    Sep 2008
    Last On
    06-25-2023 @ 06:36 AM
    Location
    Germany
    Posts
    5,032
    Local Date
    11-01-2024
    Local Time
    01:32 AM
    Well, don't try this out on a valuable part, but I once achieved a parkerization "look-alike" finish by accident.

    I had wanted to remove the rust on a couple of screw dies, and dunked them in a little pot with common-or-garden rust remover (which I think is basically a weak phosphoric acid) from the local supermarket - nothing special. Then I forgot about them. When I discovered the pot again, some weeks later, the rust had gone - and the dies had acquired a parkerized-looking surface.

    I think this could be a good way to get the buttplate looking parkerized again. And to patch up bad sections on other parts. But I would not recommend bathing them in rust remover and leaving them for weeks, as I did. That might be overdoing it and produce an area with a surface that stands out rather crassly from its surroundings.

    A bit of experimentaton on some rusty bits and pieces would be advisable, to get a feeling for the speed of transformation before trying it out of the real gun parts.
    Last edited by Patrick Chadwick; 11-03-2019 at 05:30 PM.

  4. Avoid Ads - Become a Contributing Member - Click HERE
  5. #3
    Advisory Panel browningautorifle's Avatar
    Join Date
    Jul 2008
    Last On
    Today @ 06:59 PM
    Location
    Victoria BC
    Posts
    30,402
    Real Name
    Jim
    Local Date
    10-31-2024
    Local Time
    04:32 PM
    I did that quite on purpose Patrick, same thing with the same end. I also did it with Muriatic acid believe it or not and had a parkerized looking finish apply itself. Just oil after...it's on sling hardware and still looks good. First time was phosphoric acid on a Sten barrel and left it a couple days for the deep grey. Just let it dry after and apply oil.
    Regards, Jim

  6. Thank You to browningautorifle For This Useful Post:


  7. #4
    Legacy Member Sunray's Avatar
    Join Date
    Mar 2009
    Last On
    03-29-2021 @ 03:01 PM
    Location
    London, Ontario
    Posts
    1,053
    Local Date
    10-31-2024
    Local Time
    07:32 PM
    "..."OOOO" steel wool..." With oil, not "OOOO" steel wool by itself. A light touch with a fine brass wire wheel in a bench grinder or rotary tool works too. Eye protection is essential. Assuming you have either of those.
    All the metal would have the same 'finish'. Parkerizing is a term like Kleenex. It's actually a U.S. company thing. Comes in shades of grey(depending on the metal is goes on) or black. Difference is the chemicals used. Zinc based gives the grey. Manganese the black. There was no green. That's caused by long term storage in cosmolineicon.
    There is also black phosphating that was/is used on FAL's etc. Same idea with different chemicals.
    There is no touching up Parkerizing or the other coatings. It's a coating vs a finish like bluing. You can use regular cold bluing to camouflage bare spots though.
    Isn't usual for the crests to be ground off milsurp Mausers. How easy is it to get K98icon parts where you are? You may want to replace the butt plate.
    Spelling and Grammar count!

+ Reply to Thread

Similar Threads

  1. Mauser metal work finish....
    By bigduke6 in forum Mauser Rifles
    Replies: 2
    Last Post: 03-20-2016, 10:25 AM
  2. Linseed Oil Finish - How to Clean? Refinishing?
    By MilSurpFan in forum Gunsmithing for Old Milsurps
    Replies: 17
    Last Post: 08-06-2014, 05:22 AM
  3. 1923 lithgow, to clean or not to clean?
    By BushyFromOz in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 11
    Last Post: 01-06-2011, 06:50 PM
  4. think I need this Mauser finish reamed
    By old_dood in forum Gunsmithing for Old Milsurps
    Replies: 4
    Last Post: 07-18-2009, 06:22 PM
  5. Mauser 96 original wood finish
    By daveboy in forum The Restorer's Corner
    Replies: 2
    Last Post: 06-15-2009, 09:21 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts