New guy looking for some help

[smle addict]

Very nice! You have (or will have) a Maltby produced No4 Mk I. Not quite sure of the finish; it may just be the lighting, but it looks like it was laquered. Either way, it looks to be an honest rifle.

Information

Warning: This is a relatively older thread This discussion is older than 360 days. Some information contained in it may no longer be current.

[scottsmich]

Thanks a lot! Do you know it it's normal for the serial number on the magazine to match the rifle? In these days of having so many magazines for every gun it seems like an oddity to me, but I'm guessing even then it was normal to have more than one magazine for a rifle. Just curious.

Also, do you know how much the replaced barrel band affects the collector value of the rifle?

Thanks

[smle addict]

Perfectly normal to have a magazine serialized to a rifle. I cant say with certainty that your magazine was numbered in service. True british rebuilds scribe the serial into the magazine in a much neater fashion. But, some nations were not so neat, and stamped numbers in a much more hap-hazard manner.

No need to replace the front band; that weld is normal. As far as prices go, your best bet would be to check the on-line auctions to see current pricing. Seems like the prices are all over the map nowadays.

[Alan de Enfield]

In these days of having so many magazines for every gun it seems like an oddity to me, but I'm guessing even then it was normal to have more than one magazine for a rifle.

There was only one magazine per rifle, you didn't remove the magazine except occasionally to clean the rifle, the magazine was loaded using chargers, slid into the charger-bridge (strippers in American parlance). The magazines were not simply plug-and-play and required fitting to the rifle (hence they were rarely removed as they could easily have the 'ears' bent, and just a couple of thou' out of alignment and they wouldn't feed)


List of Changes #C2792 dated 3rd June 1946 mandated that all new No4 production rifles must have their magazines numbered to the rifle, and any rifles 'in the field' must have their magazines numbered to the rifle on the next Armourers Inspection.

If you have a rifle with an un-numbered magazine, you in fact have a 'non-original' rifle as ALL rifles should have had numbered magazines in Service, certainly within (say) 12 months of June '46.
If your rifle was sold out of service prior to the LoC implementation then it could have escaped with an 'un-numbered' magazine.


Extract :

[scottsmich]

There was only one magazine per rifle, you didn't remove the magazine except occasionally to clean the rifle, the magazine was loaded using chargers, slid into the charger-bridge (strippers in American parlance). The magazines were not simply plug-and-play and required fitting to the rifle (hence they were rarely removed as they could easily have the 'ears' bent, and just a couple of thou' out of alignment and they wouldn't feed)


List of Changes #C2792 dated 3rd June 1946 mandated that all new No4 production rifles must have their magazines numbered to the rifle, and any rifles 'in the field' must have their magazines numbered to the rifle on the next Armourers Inspection.

If you have a rifle with an un-numbered magazine, you in fact have a 'non-original' rifle as ALL rifles should have had numbered magazines in Service, certainly within (say) 12 months of June '46.
If your rifle was sold out of service prior to the LoC implementation then it could have escaped with an 'un-numbered' magazine.


Extract :

Thank you Alan! That explains a couple of things and raises a new question or two. The magazine is either mismarked or mismatched. I was assuming that it was a mistake in marking, but it occurs to me that if the magazine was separated from the rifle during the process of putting it into surplus then the mistake could have been made when re-attaching them during that process. The last digit ( "3") in the serial number on the rifle is very easy to mistake for a "5" as is on the magazine.

This may explain a problem I am having with feeding ammunition. The last round in the magazine does not feed. It goes high and left of the chamber. All of the other rounds feed fine. The magazine itself seems to fit fine. I was thinking that this was due to the follower or spring. I hope it's not an issue with the ears.

#C2792 also mentions marking the foreend of the rifle with the serial number. I believe this would be on the underside of the forestock. Is that correct? This was not done on
on this rifle. I suppose the rifle could have been retired between the two effective dates of the changes. The stocks look original to me. At least they all seem to be the same wood and about the same age.

One more question if you don't mind. Should the barrel also be serialized? I attached a couple of pictures of the muzzle. It does bear some marks, but not a serial number.

[Alan de Enfield]

I hope it's not an issue with the ears.

This is not a big problem, simply VERY SLIGHTLY bend the ears (one at a time) the very smallest fraction to can manage, try cycling the rounds - any improvement or worsening. Keep fiddling about altering one then the other and 'after a few hours' you'll know why you do not remove a peoperly fitted magazine from a Lee Enfield.

#C2792 also mentions marking the foreend of the rifle with the serial number. I believe this would be on the underside of the forestock. Is that correct? This was not done on
on this rifle.

It seems some were and some were not. As you suggest there would have been a large number of rifles sold off, or gone into long term storage after the end of WW2 and the inplementation of the new markings between June '46 - JUne '47.
I have a Savage which is marked :

Attachment 120983


Barrels were rarely marked with the serial number, although some countries operated with slightly amended 'rules' and you can occasionally find numbered barrels.

For the No1 Mk3 rilfe the following instructions are to be found in the "Instructions For Armourers - 1931"

17. Each rifle must invariably be used with the breech bolt bearing the rifle number, otherwise the
lugs may not bear evenly, and the rifle may fire to the right or left; the distance from the bolt to the
end of the chamber may also be affected. When, owing to loss or damage, it becomes necessary to fit
another bolt to a rifle, the rifle should be fired for accuracy on the range. The fore-end and nose-cap
are also fitted and numbered to the rifle. Accuracy tests must always be carried out when either or both
of these components are exchanged.
18. When spare bolts, sight leaves, fore-ends and nose-caps are fitted to rifles, they will be marked
with the body number. When fitting a spare barrel with body, the whole of the components before
mentioned will be re-marked with the new body number.

[scottsmich]

Thank you for the info. I realize these are really basic questions and I appreciate you taking the time to answer.

This is not a big problem, simply VERY SLIGHTLY bend the ears (one at a time) the very smallest fraction to can manage, try cycling the rounds - any improvement or worsening. Keep fiddling about altering one then the other and 'after a few hours' you'll know why you do not remove a peoperly fitted magazine from a Lee Enfield.

I did a little more reading, and it sounds like magazine feed issues can sometimes be specific to the round being fired. I currently have 4 rounds of Winchester Super that came with the gun. They have rather mashed up soft tips and aren't what I will buy if and when I can actually find ammunition for it. (Going to look at local stores today and hope I get lucky.) I'm thinking I will wait until I have the proper ammo before adjusting. I am now a bit paranoid about not damaging the magazine, so I'd like to adjust it as little as possible.

Thanks Again

[Alan de Enfield]

Thank you for the info. I realize these are really basic questions and I appreciate you taking the time to answer.



I did a little more reading, and it sounds like magazine feed issues can sometimes be specific to the round being fired. I currently have 4 rounds of Winchester Super that came with the gun. They have rather mashed up soft tips and aren't what I will buy if and when I can actually find ammunition for it. (Going to look at local stores today and hope I get lucky.) I'm thinking I will wait until I have the proper ammo before adjusting. I am now a bit paranoid about not damaging the magazine, so I'd like to adjust it as little as possible.

Thanks Again

Forget Winchester, Remington or S&B ammunition.
If you cannot get hold of any original MkVII ammunition (HXP etc) then the Modern commercial by Prvi Partisan (PPU) is about the best 303 in the market and performs fairly closely to the original MkVII and is manufactured with mil-spec cases.

I've posted these before, but see a comparison of both Rim Thickness and case wall thickness of Win & PPU cases - guess which is which :