1939 Bren Mk.1 - just obtained & questions

[Bren1939]

Hello. A friend has just obtained a deactivated 1939 Bren Mk.I in what appears original and complete order, including cocking and dry firing.

It's stamped with "Bren Mk.1", a crown and "Enfield 1939" whilst the barrel has a few serial numbers (from A8** to X30**).

As it's a 1939 example, is there a way of tracing the serial number (B-28**) back to potentially Dunkirk, or the regiments it belonged to over its life?

Thank in advance for your advice and suggestions.

Photos below, including deactivated ammunition from June 1940:

Information

Warning: This is a relatively older thread This discussion is older than 360 days. Some information contained in it may no longer be current.

[Peter Laidler]

Not even the remotest chance in hell is the short answer. But, although these figures have been disputed by later day researchers, the census of warlike stores in August 1940, reporting on the availability of equipment to defend the realm against the forthcoming invasion states that of the c.30,000 Bren guns made up to that date (that'll be the A, B and up to the end of the C suffix letters) 27,000 were lost in France

[Brit plumber]

Hello. A friend has just obtained a deactivated 1939 Bren Mk.I in what appears original and complete order, including cocking and dry firing.

It's stamped with "Bren Mk.1", a crown and "Enfield 1939" whilst the barrel has a few serial numbers (from A8** to X30**).

As it's a 1939 example, is there a way of tracing the serial number (B-28**) back to potentially Dunkirk, or the regiments it belonged to over its life?

Thank in advance for your advice and suggestions.

Photos below, including deactivated ammunition from June 1940:

https://www.milsurps.com/images/impo...9d1b47ed-1.jpg

https://www.milsurps.com/images/impo...4f62b878-1.jpg

Any chance of PM ing me the whole number, I run a register of surviving Brens. I thought I had your gun on the register (B2824) but when I compare the photos I see its not. Also, if you post overall photos of the Bren we can tell you if its all correct. It does appear to have the correct Mk1 Barrel nut or perhaps a Mk3.

Cheers, Chris.

[Peter Laidler]

IF it's correctness yopu're after, then the magazine isn't right either!

[Bren1939]

Thank you for the information you sent following my PM, Chris. That's superb work you're doing.

As for the two magazines, thank you for the information, Peter. We do want the Bren to be "correct" whilst retaining the patina and originality it possesses already. Hence the June 1940 (deactivated) ammunition that's with it.

Therefore, advice on an appropriate 1939 magazine would be appreciated.

[Bren1939]

A few more photos, all comments, observations and advice appreciated.

[LesterH]

Nice Dovetail Brengun. This is probably one of the few that did not go to France in 39/40. It's so difficult to find a nice Dovetail these days. Often you see them with the wrong barrel, butt and bipod. However a well used Bren would have had bits replaced when maintainence was needed. Some collectors like the "rolled in the mud quality". The gun has been there and done it. However I like fairly mint and original guns and bayonets. Because I am more interested in the history and engineering. I tend to want my collection to be a reference work for future generations.IE all correct. However as collectors we pays the money and make our choices. I am sure the reenactors who roll in the mud have just as much fun as I do!
Happy new year, Lester

[Peter Laidler]

BP might not be absolutely correct about the barrel nut (sorry about this BP!). To be really original, you'll need to take the barrel nut out or look inside if it's not get-outable and see if there is a 'stop shoulder' on the underside whan it is lifted. This 'stop shoulder' was to ensure that the gun was stripped in the correct sequence. I won't go into the why's and wherefores but I'm sure someone who's a dab hand with photos will illustrate it. It's the wrong butt slide as well........ And butt slides were not a replaceable part until just after the war as I seem to recall. The stepped muzzzles of those early guns were crap too. A case of the Enfield engineers thinking that they knew more than the Czechs!

I'll let you into a little secret about pic 4. See that little taper pin that retains the stainless (it's not really stainless in a metallurgical sense....) Eliminator, flash to the barrel.... got it? That pin was originally going to be a parallel pin with a half radius recess and a sprung lever head that would spring seat/sit into the recess at the rear of the pin. It was rivetted over or circlipped in place at the other side. Then to remove the flash eliminator, you could unhook the sprung lever, rotate it through 180 degrees and then unscrew the flash eliminator off. The longer legs of the Mk1 gas plug would prevent the sprung lever from rotating should it work free from the grooved recess. So you first have to remove the gas plug THEN unclip and rotate the shaft and only then could you unscrew it in order to screw on a special blank firing flash eliminator sleeve. Being a semi sort of stainless steel, the huge build-up of carbon fouling wouldn't affect the removeability greatly (oh no.......!) so you could use normal barrels for blank firing using a simple blank muzzle end.

As I read it, the blank firing flash eliminator didn't have any sights fitted so that you couldn't actually 'aim' at anyone.

Not a lot of people know that as yet another useless bit of Enfield info

[Brit plumber]

Peter, should I assume that not all Mk1 Barrel nuts had the shoulder? I always thought they did but had them ground off later and then omitted from the Mk2 nut onwards. I only have one example with the shoulder intact, I dont know how it escaped but it matches the gun too so I aint compalining.

The good news is that your friend has the correct barrel (even if the gas hole has been reemed, it looks the part), carry handle and sleeve (Should be BSA but the patten is correct), Barrel nut (maybe with shoulder ground off), Bipod (Again would be BSA but patten is correct), Butt is correct (Again would be BSA but Patten correct).

The mag catch is Mk2 but its a cheaper item to replace, Butt plate is the later Mk1 with straight sides and as Peter said, the lower is a later Mk1 patten.

So, your friend needs a Mk1 mag at £100ish, Mk1 mag catch, Mk1 scaloped but plate with spoon, early Mk1 lower (Could prove a problem), and one of Kev Grooms repro butt handles. All in all a good start, he could always put replaced parts on ebay to recoup some cost.

[peregrinvs]

So, your friend needs a Mk1 mag at £100ish, Mk1 mag catch, Mk1 scaloped but plate with spoon, early Mk1 lower (Could prove a problem), and one of Kev Grooms repro butt handles. All in all a good start, he could always put replaced parts on ebay to recoup some cost.

Wouldn't he also need an early rounded cocking handle as well?

(And thanks again to KG for finding one for me a couple of years back )