+ Reply to Thread
Page 2 of 2 FirstFirst 1 2
Results 11 to 13 of 13

Thread: 311 or 312 bullets

Click here to increase the font size Click here to reduce the font size

Hybrid View

Pelago 311 or 312 bullets 09-10-2009, 04:15 PM
JBS Slug your rifle bores to see... 09-10-2009, 05:00 PM
gumpire I am using .310 Dia. in my... 05-23-2011, 07:54 AM
jmoore Generally, I default to the... 09-10-2009, 05:11 PM
Terry N. I have had exceptional... 09-11-2009, 07:03 AM
me2 +1_My Favorite Jacketed... 05-24-2011, 10:57 AM
m.chalmers Cast your own! The Lyman... 09-11-2009, 08:55 PM
tbonesmith I'm currently using Hornady... 05-23-2011, 08:03 AM
gunner I always used the .311... 05-24-2011, 12:25 PM
Patrick Chadwick 3 Enfields = 3 individual... 05-24-2011, 01:37 PM
gerry303ca The .312 Hornady 174 gr work... 06-03-2011, 07:14 AM
gunner That depends on what you will... 06-05-2011, 01:35 PM
smellie I have published my test... 06-06-2011, 01:44 AM
  1. #1
    FREE MEMBER
    NO Posting or PM's Allowed
    gerry303ca's Avatar
    Join Date
    May 2008
    Last On
    08-09-2015 @ 03:19 PM
    Location
    NB Canada
    Age
    83
    Posts
    31
    Local Date
    05-14-2025
    Local Time
    04:20 AM
    The .312 Hornady 174 gr work best in most of my .303B rifles, particularly in my Ross. I have the Lee mold but haven't been able to find the right load. What powder works best with cast?
    Information
    Warning: This is a relatively older thread
    This discussion is older than 360 days. Some information contained in it may no longer be current.

  2. #2
    Contributing Member gunner's Avatar
    Join Date
    May 2009
    Last On
    09-02-2018 @ 08:20 AM
    Location
    Bavaria, Germany
    Posts
    1,657
    Local Date
    05-14-2025
    Local Time
    07:20 AM
    That depends on what you will shoot, i mean the distance. If you would have good rounds only for 100 yards shooting try the TrailBoss. If they should have to work out to 300yards try a VV N140 or other slow burning powders. Fast burning powders will lead to a bunching of the bullet and smear the grooves with lead. Look at the reloading manuals of the powder makers.
    Regards Ulrich

    Nothing is impossible until you've tried it !

  3. Avoid Ads - Become a Contributing Member - Click HERE
  4. #3
    Advisory Panel smellie's Avatar
    Join Date
    Jan 2008
    Last On
    01-14-2019 @ 09:17 AM
    Location
    Virden, Man. Pop 3250, 4 miles from Wolverine's range!
    Posts
    632
    Local Date
    05-14-2025
    Local Time
    03:20 AM
    I have published my test loads several times, but I will do so again... and explain.

    With the Sierra 180 Pro-Hunter flatbase I am shooting 37 to 38 grains of 4895. Seating is to the OAL of a Mark VII Ball round. Yes, this crowds the leade just a bit, but it works. I shoot the flatbase because Enfield rifling likes it. I shoot the American bullets because they have relatively soft jackets and obturate well; also, they are extremely consistent. Velocity with this load is about 2250 ft/sec from the SMLE, about 100 ft/sec faster with the Ross. This velocity, 2250 ft/sec, was proven by test in 1910 to be the most accurate velocity with the 174-grain bullets then coming into use. With this load, I could get half an inch with a really good Lee-Enfield, an inch with a good one and less than the half-inch with a really good Ross. I say "could" because I no longer can hold a rifle steady enough to do this, even with sandbags and a rest.

    With the Hornady flatbase 150 Spire Point .312, I find that satisfactory accuracy may be obtained with 40 grains of 4064, seated so the entire bullet cannelure shows. I have had 1-ragged-hole 6-round groups from scoped rifles with this loading, at 100 yards.

    BTW, .312" was regarded as the upper limit of tolerance with the Mark VII bullet, but actual tests showed that it shot better than smaller-diameter bullets every time.

    Hope this helps.

    Good luck in the match.
    .

  5. Thank You to smellie For This Useful Post:


+ Reply to Thread
Page 2 of 2 FirstFirst 1 2

Similar Threads

  1. Cast bullets for 45 ACP
    By Gary Kaney in forum Ammunition and Reloading for Old Milsurps
    Replies: 10
    Last Post: 07-25-2009, 05:44 PM
  2. Thoughts on 9mm bullets in..
    By jjroth in forum Ammunition and Reloading for Old Milsurps
    Replies: 5
    Last Post: 05-28-2009, 08:35 PM
  3. Tipping bullets.
    By Nate in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 10
    Last Post: 05-05-2009, 12:02 PM
  4. Leftover bullets
    By Jack Stanley in forum Ammunition and Reloading for Old Milsurps
    Replies: 1
    Last Post: 04-03-2009, 09:15 PM
  5. 455 bullets
    By JHC II in forum Ammunition and Reloading for Old Milsurps
    Replies: 10
    Last Post: 05-10-2007, 06:18 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Loading...