-
FREE MEMBER
NO Posting or PM's Allowed
A (perhaps) Silly Question
Does anyone know how well a Bren magazine works 'upside down'? I.e., the cartridges feed from the top, as opposed to the normal Bren mounting. I've got this idea of modifying one to fit a No4: I can have me an Assault Enfield!
Information
|
Warning: This is a relatively older thread This discussion is older than 360 days. Some information contained in it may no longer be current. |
|
-
12-29-2009 08:03 PM
# ADS
Friends and Sponsors
-
It worked on the Charlton..................
-
-
-
Deceased January 15th, 2016
The rukes were that you were not supposed to use L4 magazines on SLRs but but could use SLR magazines on L4s in an emergency. It was explained that the L4 magazine was designed to feed with the assistance of gravity.
However, donkey's years ago, my then boss always used an L4 magazine on his SLR and, although the practice was frowned upon from on high, as far as I remember he didn't have one failure with it.
-
Your boss was right Beery! The L4 MG and L1 rifle magazines were deliberately made to be and were, fully interchangeable with no help from gravity.
The only ones that did interchange but didn't work too well were the earlier 30 round X10/L4A1 and the 20 round British trials FN mags. This was because of the original L4A1 hold open mechanism that was marginal. And when it failed, the accelerating breech block whacked the empty platform and buckled it. But the platform was modified when the magazines were made for the L4A2/L1A1. And the L4's did without a HOD.
They decided after the troop trials that a HOD is a bit of a frill that you could do without. Because even if you don't count your rounds, even during the heat and noise during a wild gun battle, you WILL hear the empty metallic ring of the breech block closing on an empty chamber. And they're right..... you do!
-
Thank You to Peter Laidler For This Useful Post:
-
FREE MEMBER
NO Posting or PM's Allowed
I have a 30 round (probably south african) FN/bren mag. I've read that they were not reliable etc. w/o gravity assist! I've never had a problem with it in the FN.
-
FREE MEMBER
NO Posting or PM's Allowed
the L2A1 or AR, Peter you would know this beast, mags could be used on the SLR. We tried them but where not favoured as when prone the mag caught the ground and also upset the balance of the rifle and sometimes the mag would release due to the supposedly weak mag catch.
So my question is where the AR mags the same as the L4?
I can't honestly remember if they where but you being an armourer over peter would know.
cheers
NED
-
The Australian made L2 rifle mags were a slightly different shape to the pom L4 magazines but both worked with each other. The Australian onew were straight and the pom ones had a very slight curve. Australia didn't buy any more of the pom L4 mags after the initial buy with the guns but just carried on using the L2 rifle mags.
Using the longer 30 round mags on the L1A1 rifle did raise your profile a few inches
As I said earlier, the only problem we had with out early L4A1 gun magazines, with the little FN type knib at the front was that the breech block could and would buckle the platform if the HOD failed....as it regularly did!
As a matter of interest, due to the sizeable amount of L4A1 guns still sloshing around in the rear echelon armouries, a last batch of FN type 30 round magazines and HOD's were manufactured quite late on
-
Thank You to Peter Laidler For This Useful Post:
-
Legacy Member
-
The Following 2 Members Say Thank You to Kev G For This Useful Post:
-
Advisory Panel
I thought he was asking about using a 303 Bren mag on a Lee Enfield? That would be a whole different thing!
-
-
Oh yes, I almost forgot.......... with the early magazine the bottom lips folded IN and it meant that in the dark, wet or in a hurry, you could insert th magazine upside down where it fails to feed! See KG's photos
Good to see the old troublesome A1 ejector block and hold open device again. They weren't interchangeable so an L4A1 couldn't be upgraded either
I'm pretty sure that given a hammer and a file that you COULD get a Bren magazine to fit into a No4, I doubt whether you'd ever get it to feed
-