-
FREE MEMBER
NO Posting or PM's Allowed
How to shorten a barrel?
I'm looking at a friends No4 sporter with the front rifling worn away, the owner/farmer says he'd prefer it shorter for easier handling anyway, so I'm wondering is there a right and wrong place to cut off the worn section for accuracy?
The rest of the rifling is is plenty sufficient for the guns modest needs as a farm/animal management tool. Thanks
Information
|
Warning: This is a relatively older thread This discussion is older than 360 days. Some information contained in it may no longer be current. |
|
-
08-15-2011 02:18 AM
# ADS
Friends and Sponsors
-
Removing the barrel from the action and parting it off in a lathe is the conventional way to shorten the barrel. But it may just be easier to counterbore it a bit until the rifling is strong. Drill and a reamer is all that's needed, but again, it's easier to do on a lathe. Why not just try countersinking it a little first? Or is the muzzle worn more than 2-3mm?
IF you are careful and know how to use a file to properly remove cut marks and square up the front, you can just hacksaw the barrel back. It's a lot more sweat producing than using fancy machines, but it can work perfectly well given some degree of mechanical aptitude. You'll still need to crown the barrel, lest the smallest accidental contact near the bore throw up a burr that'll move the zero off. That's the hardest part!
Note that the muzzle can be up to 7 degrees (maybe a little more) off plumb without reducing accuracy, but the zero will be so bad that you may run out of sight adjustment trying to zero the rifle. So, the closer to square, the better.
No burrs interuding on the bore, either, as a little one will throw off zero like a "crooked crown", at least for a while, and a big burr can lead to a small bulge, thus defeating your efforts.
Duplicating the rounded form of the old crown isn't required.
Basically, it just depends on how good the craftsman is rather than the degree of sophistication of his tools as to whether the shorter barrel will be servicable.
-
Thank You to jmoore For This Useful Post:
-
-
Advisory Panel
I sporterized a number of sporter #4's and #1mk3's some years back. All I did was to chuck the barrelled action up in the lathe and cut and crown the barrel where it came through. That gave me about 18 1/2 " of barrel. I turned the crown and turned down the outside diameter until I could tap the front sight on. I cross pinned them again and that was that. They worked for truck guns and the guys were all overjoyed to get them. BUT, I had a lathe to work with...
-
Thank You to browningautorifle For This Useful Post:
-
If the lathe has a REALLY short headstock, you don't have to remove the action. Note that the original sight base through hole is cut on a taper, though. So to do that right you MUST have some fancy tooling. Or a really good hand with a file. My first sight base barrel taper cut was done on a precision OD grinder, but that's overkill. (? Maybe...)
-
-
Brownells also sells barrel facing tools with pilots for different calibres you can use in a hand drill to crown a barrel after cutting with a hacksaw. Personally, I use a lathe.
Союз нерушимый республик свободных Сплотила навеки Великая Русь. Да здравствует созданный волей народов Единый, могучий Советский Союз!
-
Thank You to Claven2 For This Useful Post:
-
Another simple way to turn a barrel still on the action with a short swing home type hobby lathe is to mount the muzzle in the lathe with the stripped bolt in the body. Then use a centre in the concentric to the bore striker hole.
Machine to diameter the section of barrel that is going to have the foresight block re-fitted, Start the external chamfer then with a parting tool just slice the required length off!.
You could successfully complete the bore chamfer with a chamfering cutter in a slow running pillar drill.
-
Thank You to Peter Laidler For This Useful Post:
-
Legacy Member
If you do cut the barrel with a hacksaw, you can then use a lee case trimmer with a pilot that fits the bore to crown it - sounds a bit rough but I tried it on a 2-groove barrel that ended up shooting very well.
A .308 Win pilot is actually nearer .304". Put the case trimmer in the drill & be very careful. This will give you a flat but recessed crown, you can then carefully file the outside edge true to the crown.
The worst case is that the barrel is still no good.
-
Thank You to crusty For This Useful Post:
-
Legacy Member
It was recommended to me that a redneck (ie cheap and cheerful) method of crowning was to put a round head brass screw in a drill bit and use lapping paste to recrown it. Funnily enough one of my ost accurate 303s is a winchester 1895 which doesn't seem to have a crown at all, just seems to be cut flat / straight across.
-
Thank You to newcastle For This Useful Post:
-
Legacy Member
I am embarrassed to say that my first and only barrel shortening effort was with a hacksaw, file and a circular grinding stone on my m96 Mauser. Something went wrong and it shot way less than an inch at 100 and served as my varmint rifle for many years. I seriously doubt I would be that lucky twice but as a 19yo it was as good as I could do. As a mid 40 year old it's still as good as I can do
Last edited by xa-coupe; 08-16-2011 at 02:41 AM.
-
Thank You to xa-coupe For This Useful Post:
-
Legacy Member
Ps, I hate autocorrect . I will edit this when I get home so it reads properly.
-