-
Tale of an 1899 LEC (Lee Enfield Carbine) refurbishing. (Lots of pics!)
Hi everyone,
Haven't been posting in a while, life has kept me busy for the past year or so. Still, I have finally been able to spend some time on this LEC belonging to a fellow named Gary.
He trusted me with an interesting project; refurbishing a sporterized LEC.
This carbine came to me with a cut forend, no handguard, but Gary did find the middle band and the nose cap, with screws.
And, a very kind man named William agreed to lend me his complete LEC so I could use it as a guide. What a gentleman!
I started this job with a No1Mk3* forend; the action is very similar between the LEC and No1Mk3, so that was a really nice shortcut. I needed to plug a few wholes, and hide the cut-off sections in which the rear handguard retaining clip and rear sight guard would have been found on the No1Mk3.
![](https://www.milsurps.com/images/imported/2011/08/Picture009-1.jpg)
![](https://www.milsurps.com/images/imported/2011/08/Picture008-1.jpg)
![](https://www.milsurps.com/images/imported/2011/08/Picture013-1.jpg)
![](https://www.milsurps.com/images/imported/2011/08/Picture0141-1.jpg)
Then, I needed to work on the overall length, shape and thickness of the forend. Again, having a model to compare, and on which I could measure different sections, was very helpful. I mostly used a band sander for the rough, then rasps, files etc. for fine work. I was surprised to see how much material I had to remove (the shop was covered with wood dust...)
![](https://www.milsurps.com/images/imported/2011/08/Picture001-1.jpg)
![](https://www.milsurps.com/images/imported/2011/08/Picture042-1.jpg)
![](https://www.milsurps.com/images/imported/2011/08/Picture044-1.jpg)
I cut the forend to length, then I carved the front tip and drilled the screw hole so that the nose cap could fit:
![](https://www.milsurps.com/images/imported/2011/08/Picture007-1.jpg)
![](https://www.milsurps.com/images/imported/2011/08/Picture0061-1.jpg)
Then, I had to fabricate the handguard. I sourced a chunk of walnut at a local fine wood store (great placewith tons of super fancy exotic wood, etc). I found a leftover chunk that I cut with a table saw, to get a piece roughly the right length, width and height. I used a router to carve the barrel chanel, then used tha band sander to shape the exterior side.
Here's a picture of the leftover of the original wood chunk (left), a spare length cut to size, and the router'ed and sanded part before fine work.
![](https://www.milsurps.com/images/imported/2011/08/Picture022-1.jpg)
The fine work involved carving the front and rear portions of the handguard. This took time, expecially the front because it needs a tight fit in the nose cap, and there's not much wood keeping the handguard stable up front.
![](https://www.milsurps.com/images/imported/2011/08/Picture024-1.jpg)
The rear has a funny shape which is still rough in this picture:
![](https://www.milsurps.com/images/imported/2011/08/Picture017-1.jpg)
Here is the current status of the project. The handguard fits, with the nose cap and middle band. Fine sanding is next, and then linseed oil
... oh and I need to work on the butt stock too. The original is still good and won't require much.
![](https://www.milsurps.com/images/imported/2011/08/Picture019-1.jpg)
![](https://www.milsurps.com/images/imported/2011/08/Picture020-1.jpg)
![](https://www.milsurps.com/images/imported/2011/08/Picture021-1.jpg)
![](https://www.milsurps.com/images/imported/2011/08/Picture023-1.jpg)
I hope you enjoyed seeing this progress report. Cheers!
Lou
Information
|
Warning: This is a relatively older thread This discussion is older than 360 days. Some information contained in it may no longer be current. |
|
-
The Following 13 Members Say Thank You to louthepou For This Useful Post:
A. F Medic,
Badger,
Bearclaw,
bigduke6,
Emri,
Jc5,
jmoore,
m4a3sherman,
mike1967,
Paul S.,
paulseamus,
saddler,
tbonesmith
-
08-03-2011 09:40 AM
# ADS
Friends and Sponsors
-
Awesome ... ![Thumbs Up](images/smilies/TUp.gif)
Thanks for posting the ongoing process .... ![Smile](images/smilies/smile.gif)
Regards,
Doug
-
-
-
Excellent work Lou, if you start knocking out the the handgaurds am sure you would make a few $, looking for one myself, also need the fore-end but will splice a piece into the original what was cut down.
-
-
Contributing Member
Very nice, where were you when I was scratching around like a chicken in a chook yard doing a similar job years ago?
-
-
Amsdorf
Guest
Can't wait to see the the final product.
-
-
Legacy Member
-
-
You ought to I.D. your work in the barrel channel for future reference.
-
-
Nice work, that looks like a serious amount hours there.
-
-
Legacy Member
Those early carbines are beautiful. I'd love to get my hands on one someday.
-
-
-
The Following 4 Members Say Thank You to louthepou For This Useful Post: