+ Reply to Thread
Results 1 to 4 of 4

Thread: Wad trouble firing Remington 1858

Click here to increase the font size Click here to reduce the font size

Hybrid View

  1. #1
    FREE MEMBER
    NO Posting or PM's Allowed
    RobsTV's Avatar
    Join Date
    Sep 2011
    Last On
    10-26-2018 @ 03:56 PM
    Location
    Florida
    Posts
    12
    Local Date
    06-01-2024
    Local Time
    06:57 PM

    Wad trouble firing Remington 1858

    Have an original Remington 1858 (approx 1864 build date), not a replica.

    Loaded with 22.5gr (by volume) Triple Seven FFFg, a wonderwad, Hornaday .454 ball (slight lead shavings during insertion), and a little black powder lube on top for good measure.

    Rarely can I fire all six rounds without a wonderwad jamming up the works from last shot fired. The wonderwad is stuck between cylinder and barrel, preventing cylinder from rotating. Must remove cylinder to clear. Might get all 6 shots off. Might jam from wad after only 2 shots.

    I think I am doing everything correct. If I omit the wad, then there will be space between powder and ball, won't go in further with plunger arm, so wad is used as filler more than chainfire prevention. Plus also hear pistol is more accurate the closer ball is to barrel. Only tested accuracy at 50 yards, and was not accurate at all. All over the place, high and low. didn't have time to first test at 25 yards or less. Can not locate any black powder around here, so stuck with the Triple Seven. Black powder might allow more volume, which then would not require a wad.

    Any ideas on how to make this perform more reliably?

    Thanks

    (edit: Although this section seems correct for topic, this might have been better if I posted it in BP rifle section. Couldn't see how to delete, so if it could be moved, great)
    Information
    Warning: This is a relatively older thread
    This discussion is older than 360 days. Some information contained in it may no longer be current.
    Last edited by RobsTV; 10-04-2011 at 04:11 PM. Reason: spelin

  2. #2
    Advisory Panel

    jmoore's Avatar
    Join Date
    Mar 2009
    Last On
    06-09-2023 @ 04:20 AM
    Location
    US of A
    Posts
    7,066
    Local Date
    06-01-2024
    Local Time
    06:57 PM
    Perhaps substituting Cream of Wheat for the wad? It's just filler. But having never used substitute powders in black powder revolvers, it's just an untested idea. I've always just used BP and no wads- just grease in front.

  3. Avoid Ads - Become a Contributing Member - Click HERE
  4. #3
    FREE MEMBER
    NO Posting or PM's Allowed
    Johnny Peppers's Avatar
    Join Date
    Mar 2009
    Last On
    05-01-2015 @ 11:25 PM
    Posts
    1,810
    Local Date
    06-01-2024
    Local Time
    05:57 PM
    Sounds like too much clearance between cylinder face and barrel, and the wad is detouring out when it gets to the gap. I would take Jmoore's advice and try a filler to see if that works.

  5. #4
    FREE MEMBER
    NO Posting or PM's Allowed
    Kwizard's Avatar
    Join Date
    Oct 2011
    Last On
    03-22-2014 @ 08:37 PM
    Location
    TEXAS
    Posts
    6
    Local Date
    06-01-2024
    Local Time
    04:57 PM
    Cornmeal is cheaper than Cream O Wheat, and it compresses very nicely.

+ Reply to Thread

Similar Threads

  1. Trouble with my K98
    By Thumper in forum Mauser Rifles
    Replies: 6
    Last Post: 10-01-2011, 09:55 AM
  2. Having trouble identifying mag catch
    By Arcieri in forum M1/M2 Carbine
    Replies: 6
    Last Post: 09-12-2011, 09:29 PM
  3. M91/30 trouble loading magazine
    By blackcat_attilio in forum Soviet Bloc Rifles
    Replies: 10
    Last Post: 03-16-2011, 01:53 AM
  4. Inland sighting trouble?
    By chainsaw in forum M1/M2 Carbine
    Replies: 12
    Last Post: 11-18-2010, 07:50 PM
  5. TZZ 223 Brass Primeing Trouble ?
    By Weez556 in forum Ammunition and Reloading for Old Milsurps
    Replies: 4
    Last Post: 03-06-2009, 11:32 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts