+ Reply to Thread
Page 1 of 2 1 2 LastLast
Results 1 to 10 of 15

Thread: New to me, First Martini

Click here to increase the font size Click here to reduce the font size
  1. #1
    Legacy Member BVZ24's Avatar
    Join Date
    Oct 2021
    Last On
    Today @ 06:25 PM
    Location
    WI
    Posts
    193
    Local Date
    10-31-2024
    Local Time
    05:51 PM

    New to me, First Martini

    Picked up my first real Britishicon martini rifle (my first being a khyber from a sight unseen lot). I'm not super familiar with Martini Enfield Riflesicon, other than to know when it's real and when it's fake. I know it's converted to 303, in 1895. This rifle is in very neglected condition, but most likely was in very good condition when it was put away. I essentially wanted a placeholder until I could find one in VG condition, which I have been after for years.
    I have taken down the khyber, and found it rather easy. The khyber has a long lee nose cap, rather than the real front band.
    I'd like to evaluate how much pitting I have under the forestock, but I'm having difficulties drifting the front pin. I'll also most likely need to use a broken screw remover on the hook plate. The forestock is missing a chip from the front of the hook plate, and the "repair" was just to sand it flat, so the hook plate sticks up.

    Aside from the questionable forestock and barrel, the action functions and extracts good as is, and the firing pin indicator moves.

    Assuming I can remove the forestock to check condition and repair the chip, I would like to shoot this rifle. I have heard conflicting information that "It's not designed for MK 7 ammo" to "303 is nothing compared to 577-450 that it was designed for"

    I'm already thinking about repair options. I do have access to the khyber, which was sold to a buddy for wall hanging duty, and can strip that for a fake forestock, fake hook plate, and if needed, a real, but heavily sanded and re-blued, 303 Martini barrel. It even has extractor cuts.
    IMA has a reproduction stock available, has anyone tried to make it work?
    Can provide more pictures if needed.
    https://ibb.co/cgbfBt2
    https://ibb.co/C2TPGnz
    https://ibb.co/kHN498Z
    Information
    Warning: This is a relatively older thread
    This discussion is older than 360 days. Some information contained in it may no longer be current.

  2. # ADS
    Friends and Sponsors
    Join Date
    October 2006
    Location
    Milsurps.Com
    Posts
    All Threads
    A Collector's View - The SMLE Short Magazine Lee Enfield 1903-1989. It is 300 8.5x11 inch pages with 1,000+ photo’s, most in color, and each book is serial-numbered.  Covering the SMLE from 1903 to the end of production in India in 1989 it looks at how each model differs and manufacturer differences from a collecting point of view along with the major accessories that could be attached to the rifle. For the record this is not a moneymaker, I hope just to break even, eventually, at $80/book plus shipping.  In the USA shipping is $5.00 for media mail.  I will accept PayPal, Zelle, MO and good old checks (and cash if you want to stop by for a tour!).  CLICK BANNER to send me a PM for International pricing and shipping. Manufacturer of various vintage rifle scopes for the 1903 such as our M73G4 (reproduction of the Weaver 330C) and Malcolm 8X Gen II (Unertl reproduction). Several of our scopes are used in the CMP Vintage Sniper competition on top of 1903 rifles. Brian Dick ... BDL Ltd. - Specializing in British and Commonwealth weapons Specializing in premium ammunition and reloading components. Your source for the finest in High Power Competition Gear. Here at T-bones Shipwrighting we specialise in vintage service rifle: re-barrelling, bedding, repairs, modifications and accurizing. We also provide importation services for firearms, parts and weapons, for both private or commercial businesses.
     

  3. #2
    Legacy Member Daan Kemp's Avatar
    Join Date
    Jan 2016
    Last On
    Today @ 02:16 PM
    Location
    Centurion RSA
    Age
    73
    Posts
    1,423
    Real Name
    Daan Kemp
    Local Date
    11-01-2024
    Local Time
    12:51 AM
    The change over to Mk 7 cartridges was about 1910, and the Martinis soldiered on in the colonies for many years later. The change over was mainly to a spitzer and lighter bullet at a higher velocity commensurate with chamber pressures. And the Mk 6 cartridges disappeared. If the Mk 6 disappeared why would the Martinis remained in service?

    The 577/450 was a black powder relatively low pressure cartridge.

    I would seriously doubt if the Brits would convert the Martinis to 303 without checking chamber pressures, and use said converted Martinis with Mk 7 ammunition if it wasn't safe. They would also have ensured that all knew if the Mk 7 wasn't to be used in converted Martinis.

    However, check your Martini to ensure it is indeed safe to shoot.

  4. Avoid Ads - Become a Contributing Member - Click HERE
  5. #3
    Contributing Member Doco overboard's Avatar
    Join Date
    Jun 2015
    Last On
    Today @ 06:39 PM
    Location
    Delmarva Peninsula
    Posts
    453
    Real Name
    Brian Stiles
    Local Date
    10-31-2024
    Local Time
    06:51 PM
    Good advice above thank you.
    Especially the firing pin protrusion I would more than likely be checking first.
    That’s what I learned with a Martini rifle I just picked up.
    It was the last thing I checked , and glad I did.
    I’ll be checking that first thing before anything else from here out.

  6. #4
    Legacy Member BVZ24's Avatar
    Join Date
    Oct 2021
    Last On
    Today @ 06:25 PM
    Location
    WI
    Posts
    193
    Local Date
    10-31-2024
    Local Time
    05:51 PM
    Thread Starter
    Screws are all rusted stuck fairly good. I'm not sure I'm getting this stock off. The front pin will not budge with a bench vice either. The good? news is that the stripped screw won't be a problem, because the wood is so soft the plate should just fall out.
    I was planning on making a cut out and replace repair in that spot anyways.
    Based on the rust from underneath the missing handguard, and the soft condition of the wood, I am assuming the underside probably looks like the surface of the moon. My barrel will need to be welded or replaced, if the action remains serviceable. The bore is pitted but sharp, and the crown is recognisable.
    It would be nice to actually know what the barrel looks like before I jump to conclusions.

  7. #5
    Contributing Member Flying10uk's Avatar
    Join Date
    Feb 2015
    Last On
    08-11-2024 @ 10:05 PM
    Location
    UK
    Posts
    5,244
    Local Date
    10-31-2024
    Local Time
    11:51 PM
    Quote Originally Posted by BVZ24 View Post
    Screws are all rusted stuck fairly good.
    Perhaps you need to apply some penetrating oil first and let it soak in. With stuck screw fasteners it sometimes helps to first try tightening a tiny fraction before loosening and then alternating between fractionally tightening and loosening until the fastener, in this case a screw, becomes loose.

  8. #6
    Contributing Member Doco overboard's Avatar
    Join Date
    Jun 2015
    Last On
    Today @ 06:39 PM
    Location
    Delmarva Peninsula
    Posts
    453
    Real Name
    Brian Stiles
    Local Date
    10-31-2024
    Local Time
    06:51 PM
    You never know, maybe the barrel underside will be coated with old grease that preserved it somewhat.
    That's what I found when I broke mine down.
    It seemed as if it was made of animal fat or something.

    The exterior was blackened from where it dried and caked hard like varnish.
    Kroil freed everything else right up after a quick soak.

  9. #7
    Legacy Member jamie5070's Avatar
    Join Date
    Mar 2009
    Last On
    10-21-2024 @ 08:17 PM
    Location
    tucson, arizona
    Posts
    553
    Local Date
    10-31-2024
    Local Time
    05:51 PM
    The pins aren't supposed to be removed. The screws would be loosened enough to get the band over them. Try soaking the band screws with penetrating oil. Then with a properly fitted screw driver, try turning it in both directions. Give the screw driver some taps. With a screw driver bit in the slot, heat the bit with a torch. It will transfer heat to the screw.
    Also, look up british militaria forums, on tapatalk, for help. If nothing else works, you can run a dremel cut off wheel through the band slot and replace it
    john

  10. #8
    Legacy Member BVZ24's Avatar
    Join Date
    Oct 2021
    Last On
    Today @ 06:25 PM
    Location
    WI
    Posts
    193
    Local Date
    10-31-2024
    Local Time
    05:51 PM
    Thread Starter
    The pin in question is the front band cross pin. I can get the screws out at this point.

  11. #9
    Legacy Member Daan Kemp's Avatar
    Join Date
    Jan 2016
    Last On
    Today @ 02:16 PM
    Location
    Centurion RSA
    Age
    73
    Posts
    1,423
    Real Name
    Daan Kemp
    Local Date
    11-01-2024
    Local Time
    12:51 AM
    Pictures would help.

  12. #10
    Legacy Member BVZ24's Avatar
    Join Date
    Oct 2021
    Last On
    Today @ 06:25 PM
    Location
    WI
    Posts
    193
    Local Date
    10-31-2024
    Local Time
    05:51 PM
    Thread Starter
    This pin.
    The front band swivel screw also appears to have a retainer on it. I got it as loose as it will go without popping the retainer.

    IMG-20220825-065027 — ImgBB

+ Reply to Thread
Page 1 of 2 1 2 LastLast

Similar Threads

  1. Martini AC MK2
    By mrclark303 in forum Martini Henry Rifles
    Replies: 3
    Last Post: 01-13-2022, 04:50 AM
  2. BSA Martini 12
    By old tanker in forum .22 Smallbore
    Replies: 3
    Last Post: 07-21-2021, 04:15 PM
  3. Martini Enfield 303
    By Oysters in forum Martini Henry Rifles
    Replies: 10
    Last Post: 12-02-2020, 12:44 PM
  4. Canadian Martini Henry Rifle MkVI (Martini Metford MkII)
    By Lee Enfield in forum Martini Henry Rifles
    Replies: 6
    Last Post: 09-04-2020, 07:34 PM
  5. New BSA Martini
    By Calfed in forum .22 Smallbore
    Replies: 8
    Last Post: 02-06-2012, 09:01 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts