-
FREE MEMBER
NO Posting or PM's Allowed
Remington Rand second variation slide marking Dulite
Thank-you to all those who provided help on the correct Keyes grips question. The pair on this one are marked Star 12 and 14 inside. This is the pistol I found in Tampa last week and had transferred to my dealer locally. It is now well oiled and resting in my safe. The Dulite is about 95%; the shine is the light coat of CLP I have on it. Barrel is Springfield Arsenal (SP). I had an "S" marked magazine now mated to it. Will keep looking for a "G" in similar condition to pistol. There was a late war parkerized Remington Rand right next to this one in about 50% condition for $300 more... go figure? I guess they figured the "blued" version was incorrect. Slide stop, safety and mainspring housing are checkered.
Information
|
Warning: This is a relatively older thread This discussion is older than 360 days. Some information contained in it may no longer be current. |
|
Last edited by Arisaka99; 01-08-2010 at 10:06 PM.
-
01-08-2010 05:38 PM
# ADS
Friends and Sponsors
-
FREE MEMBER
NO Posting or PM's Allowed
Does the Springfield Armory barrel have a heat lot number stamped above the LH lug where the 'S P' is located ?????
I have a couple of extra 'G' General Shaver mags..... and a correct/original 'SP' Type 14 barrel.
usgi45s@hotmail.com
Bob
Last edited by oldcanuck; 01-08-2010 at 09:12 PM.
-
-
FREE MEMBER
NO Posting or PM's Allowed
No heat lot number. Should there be? The 1911 page shows both as correct. I would love to chat about one of the "G" mags.
-
FREE MEMBER
NO Posting or PM's Allowed
nice looking pistola!!
-
FREE MEMBER
NO Posting or PM's Allowed
Originally Posted by
Arisaka99
No heat lot number. Should there be? The 1911 page shows both as correct. I would love to chat about one of the "G" mags.
Yes, there should be a Heat Lot number on your bbl. S and P on either lugs is an earlier mfd bbl for a WWI era Springfield.
My email is usgi45s@hotmail.com
Bob
-
FREE MEMBER
NO Posting or PM's Allowed
The photo shows that your RR has a Colt 1911 slide stop....
-
FREE MEMBER
NO Posting or PM's Allowed
This is one of the ~3k WWI style slide stops purchased from Colt perhaps? Could the barrel also be a left over part from early production parts purchases from Springfield? Thank-you very much for your eyes on this one; the expertise is deeply appreciated. I am limited to date to google and some minimal personal observations.
Last edited by Arisaka99; 01-09-2010 at 04:37 PM.
-
FREE MEMBER
NO Posting or PM's Allowed
Here is a photo comparison of a 1911 slide stop with a New In The Box Type II Remington Rand that has a DuLite finish... This RR has a slotted slide stop and is a later gun SN 1013501.. Note that the 1911 slide stop is undercut below the thumb area...
-
FREE MEMBER
NO Posting or PM's Allowed
Thanks John. Appreciate the time taken with the photos. Thank-you to Bob as well for his PM and email comments. Some "off kilter" parts on this one it seems.
Last edited by Arisaka99; 01-09-2010 at 07:19 PM.
-
Legacy Member
Brad, You have a very nice early type 2 Remington Rand. An S mag is possible since Rem Rand used S, R, L and G marked magazines, not just G.
I missed the grip part but I would expect to see no ring grips on a Rem Rand that early. That may have been covered already. Do not worry about the numbers, the grips often have different numbers because those are merely the number on a given mold.
On the barrel, I have seen a few probably original barrels without a heat lot number but am not certain that is correct. It seems it could be correct since many of the parts used on early Rem Rands came from Springfield and some were left over from WW1. You can check the wear patterns where the barrel contacts the slide and get an idea if the two parts have been together for a long time therefore supporting probable originality. 1911 slide stops do come up on early Rem Rands and early Ithacas. This happened as late as Feb. 1943 at Rem Rand according to Clawson. The slide stop on John's pistol would not be correct for your much earlier pistol IMHO.
If it were my pistol I would not change a thing. That is my personal preference because so many guns have been made correct according to a book or an expert only to later discover that they were original before they were messed with. That being said, I often will get the parts I think or know that are wrong and put them aside for that pistol for possible future use or for sale with the pistol. That way the potential buyer can have the parts to make it "correct" to his satisfaction. The parts seem to be going up in value faster than the pistol so having them is a plus in any event.
Very nice pistol even if, and maybe not, a small part or two is not original. Congratulations on a nice find.
Last edited by mike radford; 01-09-2010 at 09:49 PM.
-