+ Reply to Thread
Results 1 to 5 of 5

Thread: Stuck cases in a Cz 52 pistol

Click here to increase the font size Click here to reduce the font size

Hybrid View

  1. #1
    FREE MEMBER
    NO Posting or PM's Allowed
    Pattern14's Avatar
    Join Date
    Sep 2009
    Last On
    05-15-2015 @ 05:17 PM
    Location
    Harrisburg, Pennsylvania
    Posts
    210
    Local Date
    05-27-2024
    Local Time
    03:43 AM

    Stuck cases in a Cz 52 pistol

    I purchased several boxes of 7.62 x 25mm a few years ago to use in a Romanian Cz 52 and have been having problems with the cases sticking in the chamber. The headstamp is 22 and the year is 1982. With the barrel removed and the cartridges pushed into the chamber by hand, the rounds are hard to remove and I believe the cartridges may be out of specification. I even had an instance where a live round went into the chamber, failed to fire, and would not eject until I was able to tap the slide back with a small hammer.

    When I use a small needle file to chamfer the outside neck edge of the round, I can pull the cartridges out easily. My question is that there must be a better way to resolve the problem. I would hate to have to dump these boxes but I'm not prepared to spend hours filing down individual cartridges.
    Information
    Warning: This is a relatively older thread
    This discussion is older than 360 days. Some information contained in it may no longer be current.

  2. #2
    FREE MEMBER
    NO Posting or PM's Allowed
    JBS's Avatar
    Join Date
    Aug 2009
    Last On
    07-08-2019 @ 09:37 AM
    Location
    removed
    Posts
    455
    Local Date
    05-27-2024
    Local Time
    02:43 AM
    You can give the rounds a light kiss with a taper crimp die.

  3. Avoid Ads - Become a Contributing Member - Click HERE
  4. #3
    FREE MEMBER
    NO Posting or PM's Allowed
    Pattern14's Avatar
    Join Date
    Sep 2009
    Last On
    05-15-2015 @ 05:17 PM
    Location
    Harrisburg, Pennsylvania
    Posts
    210
    Local Date
    05-27-2024
    Local Time
    03:43 AM
    Thread Starter
    I thought of that but don't have a crimp die that will fit without some sort of permanent modification.

  5. #4
    FREE MEMBER
    NO Posting or PM's Allowed
    JBS's Avatar
    Join Date
    Aug 2009
    Last On
    07-08-2019 @ 09:37 AM
    Location
    removed
    Posts
    455
    Local Date
    05-27-2024
    Local Time
    02:43 AM
    Well, you have a 30 Luger or a 30 Mauser set of Dies ? You can always do it the hard way. it's faster than a file but not by much. roll the necks between two steel plates to squeeze the ridge at the mouth down. Don't do it to hard or the bullets will fall out.

  6. #5
    FREE MEMBER
    NO Posting or PM's Allowed
    yodar's Avatar
    Join Date
    Jun 2009
    Last On
    04-13-2010 @ 08:40 PM
    Posts
    2
    Local Date
    05-27-2024
    Local Time
    02:43 AM
    I reload 7.62 x 25 with cases i make from .223 brass and have several hundred rounds of Romanian 7.62 x 25 to shoot before i get back to reloading it.



    These have too heavy a crip and are rejects

    BUT Nobody has addressed the issue of chamber incongruities that might be snagging the ejection

    Clean the chamber out real well with various solvents, lacquer thinner, Ed's red, CLP, BreakFree, and use a bore brush in the chamber too! And scrape a nut pick around the chamber and see if you feel a defect.

    As a C & R 03, I have had experience with a lotta Milsurps, and chamber issues are real.
    yodar
    Last edited by yodar; 12-31-2009 at 07:54 PM.

+ Reply to Thread

Similar Threads

  1. gas piston stuck in new Rock Ola
    By colreed in forum M1/M2 Carbine
    Replies: 7
    Last Post: 07-19-2009, 01:53 PM
  2. 7.7 Jap from 30/06 cases
    By sigman2 in forum Japanese Rifles
    Replies: 10
    Last Post: 04-30-2009, 10:06 AM
  3. removing a stuck front sight, base.
    By Chuckindenver in forum Gunsmithing for Old Milsurps
    Replies: 1
    Last Post: 04-18-2009, 12:40 PM
  4. removing a stuck front sight, base. tip of the week.
    By Chuckindenver in forum M1903/1903A3/A4 Springfield Rifle
    Replies: 3
    Last Post: 04-11-2009, 12:41 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts