+ Reply to Thread
Results 1 to 10 of 11

Thread: Remove oil from cracked stock without damaging finish?

Click here to increase the font size Click here to reduce the font size

Hybrid View

  1. #1
    Legacy Member usabaker's Avatar
    Join Date
    May 2017
    Last On
    12-30-2024 @ 01:41 PM
    Location
    San Deigo, CA
    Posts
    1,780
    Real Name
    Bill Baker
    Local Date
    07-01-2025
    Local Time
    07:39 PM
    Quote Originally Posted by FLOPPY_DISK View Post
    The oil needs to be removed from the stock so that the cracks can be glued. I don't want these cracks to spread. How does one remove oil from a stock without damaging a finish that is known to be somewhat delicate?
    I think what you are asking is how to remove the oil that has crept inside the crack without removing the finish? This is not an easy solution without seeing the cracks and location. What you will need to do is flood the crack so that the oil and dirt in the cracks are removed enough so that the glue can adhere to the wood. One of the reasons that you are not getting an answer to your question is that there is not enough information and because no one wants to take the responsibility and blame if the corrective procedure doesn't take.

    You are going to lose some finish in the area of the repair no matter what if you use what I suggest, and I take no responsibility for any outcome, remember a glued crack is not reversible, the glued area will end up stronger then the areas around it.

    I can only give you general information on cleaning the cracks because I do not know the extent of the crack, placement, and what process I could use to compress the crack while the glue drys. I'm only going to tell you how "I" clean SOME cracks out.

    DISCLAIMER ***** USE Personal Protective Equipment to include, CHEMICAL GOGGLES and a Respirator! Don't do this around heat or open flame, No Smokin of Anything. I'm not responsible if you injure yourself ************* Don't Do This at Home Kids

    Since you want to limit the removal of finish you will need to protect the area around the crack. Sometimes the stuff used to protect the crack can also remove the finish or cause blemishes. This is the case with products some I've seen and heard other use like Plasti Dip and Flex Seal, you will read about them I do not recommend using them. They use solvents as their thinning agent and this can (may) remove or damage your finish. I use a brushable SKIN SAFE product called Dragon Skin by Smooth On https://www.smooth-on.com/product-line/dragon-skin/ because your stock is oiled, it will stick but not 100 percent and the TechSpray E-LINE IPA can work up under it. This is why I say you will lose some finish. Try the Dragon Skin it on an inconspicuous area before applying it to the crack area to test if it will react/remove the finish. I have not had a problem with it, but I have not tried it on every possible aged finish.

    Once you test it won't damage the finish, brush the Dragon Skin on to the stock around (not in or on the crack) crack to be repaired. Once the Dragon Skin has dried invert the stock so the crack is facing down. Now use a product called TechSpray E-LINE IPA in aerosol form.

    https://www.techspray.com/content/ms...OL_ENG_TDS.pdf

    TechSpray E-LINE IPA is a 99.8% pure isopropyl alcohol product that comes with a tube that connects to the spray nozzle like the one you get with WD-40. Put the tube on the spray nozzle and hold it on the crack starting that one and moving to the other while spraying to flood the crack, you should see dirt and oil coming out with the liquid. Wait 3 minutes between each run so the solvent has time to dissolve more oils, but not dry out. Repeat until the runoff looks clean. You can use a white paper to stick in the crack to see how clean it might be if you push the paper in, it should come out clean; if not repeat.

    Whatever the TechSpray E-LINE IPA his will get cleaned off, so make sure you cover the areas you don't want to be touched. Check the Dragon Skin often and replace it as necessary, but let the TechSpray E-LINE IPA dry first!

    AGAIN: Since I am not the one performing the repair and cleaning, I am not responsible for the results you get.

    Let the stock dry at a minimum overnight before starting the glue repair. For the glue I would use Acraglass with black dye, using LIGHT air pressure to force it down into the cracks.
    Information
    Warning: This is a relatively older thread
    This discussion is older than 360 days. Some information contained in it may no longer be current.
    Last edited by usabaker; 12-06-2019 at 01:19 AM.
    Veteran US Navy Seabees - US Army Corps of Engineers - American Legion Post 0867
    " Only two defining forces have offered to die for me. 1.) Jesus Christ 2.) The American G.I. "One died for your soul, the other for your freedom! "

+ Reply to Thread

Similar Threads

  1. Cracked Stock
    By mrkurtz in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 2
    Last Post: 01-26-2015, 06:11 AM
  2. Samco cracked stock K31
    By WCBeck in forum Swiss Rifles
    Replies: 8
    Last Post: 04-27-2013, 10:55 PM
  3. M1917 cracked stock
    By dsk in forum Pattern 1913/1914 and M1917 Rifles
    Replies: 10
    Last Post: 10-29-2011, 06:48 PM
  4. Swede M96 with cracked stock-HOW TO FIX?
    By blano86 in forum Gunsmithing for Old Milsurps
    Replies: 5
    Last Post: 02-11-2010, 08:01 PM
  5. Strongest Cleaner to remove cosmoling but not hurt Finish
    By gerry in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 6
    Last Post: 06-26-2009, 01:22 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts