+ Reply to Thread
Page 1 of 2 1 2 LastLast
Results 1 to 10 of 16

Thread: New barrel on Ross MK III

Click here to increase the font size Click here to reduce the font size
  1. #1
    Member Abitnutz's Avatar
    Join Date
    Sep 2019
    Last On
    Yesterday @ 06:12 PM
    Location
    Waynesville, Ohio USA
    Posts
    12
    Local Date
    10-24-2020
    Local Time
    11:18 AM

    New barrel on Ross MK III

    Well, it's finally done after months of waiting for tooling and parts. I have a Ross Mk IIIB that is equipped with a Cooey rear sight. It was in fine overall shape except that the barrel was so bad it could be used for a sewer pipe.

    I saw that Krieger made barrels big enough for the MK III action if you could find a gunsmith that could thread it, chamber it, cut the extractor groove and generally wrestle it on to the MK III action.

    I was told that the CMPicon in Alabama would do it but when I called they wouldn't even talk to me or return my phone calls. Luckily my local gunsmith was either up for the challenge or too ignorant to know what he was getting into.

    My local guy took the original barrel off. It was on so tight he had to make a relief cut to get it off. I shipped it off to Krieger to copy the contour and get general dimensions....then I waited.

    I decided to go with a .308 bore with a 1-10 twist and 5R rifling. The barrel is so marked. I know everyone is freaking out about now but I handload everything. If you look at what's available in factory loaded ammo in .303 there is just nothing I think is worth shooting. So if I have to handload anyway, there are just so many more choices in .308 than .311-312. Also, I could get 5R rifling witch I find a lot easier to clean.

    I had Manson make the custom reamer. They knew exactly what I needed and I had it way before the barrel showed up.



    So it's now done. It's all rust blued and seems to match up really well. I haven't done any serious shooting yet but I'm sure it won't keyhole like it used to.

    It's a MK IIIB the previous owner put on a Cooey sight but left on the front 3 prong sight. It's not a terrible sight picture but I'm thinking about swapping someone for a standard MK III hooded front sight. I think that make have a much better sight picture.

    This whole project was nowhere near cheap so if someone else is thinking about it...beware. It's a straight forward job just with bigger numbers.

  2. # ADS
    Friends and Sponsors
    Join Date
    October 2006
    Location
    Milsurps.Com
    Posts
    All Threads
    Banner AD Space Available - Click HERE to Inquire Family owned and operated since 1962, Simpson LTD is the largest collector firearms store in the Midwest. Our globally sourced inventory represents many eras, with an emphasis on World War II and our favorite firearm, the Luger, of which we typically have 2,500 in stock.  Inventory changes daily with 10,000 firearms ready to ship; along with accessories, militaria, and hundreds of book titles. We also offer appraisals, consignment services ranging from single items to full collections, and we are one of the most reliable and competitively priced import and export services available.  We do not offer parts or gunsmithing, but we have a little bit of everything else. Visit our website for more information and our new technical video series Speaking Luger, and like Simpson Ltd on Facebook for updates, previews, and more. LIMITED TIME OFFER FROM THE AMERICAN GUNSMITHING INSTITUTE: Get Immediate Online Access To AGI's NEW Armorer's Course for Glock Pistols, Covering Every Generation of Glocks, Including the Latest Model 42/43 and Double Stack Pistols for ONLY $7.00! Brian Dick ... BDL Ltd. - Specializing in British and Commonwealth weapons Chuck in Denver ... Buy-Sell-Trade .. Guns, Cars Motorcycles Your source for the finest in High Power Competition Gear. Here at T-bones Shipwrighting we specialise in vintage service rifle: re-barrelling, bedding, repairs, modifications and accurizing. We also provide importation services for firearms, parts and weapons, for both private or commercial businesses. Banner AD Space Available - Click HERE to Inquire
     

  3. #2
    Contributing Member NORTHOF60's Avatar
    Join Date
    Jun 2018
    Last On
    Today @ 10:22 AM
    Location
    Scarborough, Ontario, Canada
    Posts
    186
    Local Date
    10-24-2020
    Local Time
    11:18 AM
    Have a great time at the range. I hope that you enjoy you custom Ross.
    Some do, some don't; some will, some won't; I might ...

  4. Avoid Ads - Become a Contributing Member - Click HERE
  5. #3
    Member Sharpshooter1944's Avatar
    Join Date
    Jan 2020
    Last On
    07-15-2020 @ 12:29 PM
    Location
    Michigan, USA
    Posts
    31
    Local Date
    10-24-2020
    Local Time
    11:18 AM
    How about a pic?

  6. #4
    Member Abitnutz's Avatar
    Join Date
    Sep 2019
    Last On
    Yesterday @ 06:12 PM
    Location
    Waynesville, Ohio USA
    Posts
    12
    Local Date
    10-24-2020
    Local Time
    11:18 AM
    Thread Starter
    Will do. I'll try and show as much as I can of the barrel.

  7. #5
    Advisory Panel browningautorifle's Avatar
    Join Date
    Jul 2008
    Last On
    Today @ 06:09 AM
    Location
    Victoria BC
    Posts
    24,237
    Local Date
    10-24-2020
    Local Time
    08:18 AM
    Quote Originally Posted by Abitnutz View Post
    I decided to go with a .308 bore with a 1-10 twist and 5R rifling. The barrel is so marked. I know everyone is freaking out about now but I handload everything.
    We've discussed that here once a while back and I still think that's the right way to go anyway. Just like you explain, the bullet choice is there. I used to use .308 bullets in a very tight bore #4T and it shot very well for me. I wait with bated breath for the targets to be marched past us here... Anyway it's your rifle and I doubt it'll go anywhere soon.
    Regards, Jim

  8. #6
    Contributing Member #1oilman's Avatar
    Join Date
    Sep 2016
    Last On
    10-18-2020 @ 11:21 AM
    Location
    southern Ontario
    Posts
    227
    Local Date
    10-24-2020
    Local Time
    11:18 AM
    Sounds like a great project, can you give us some insight on the cost of the barrel? I know I would like one and I'm sure there will be plenty more wanting them as well!

  9. #7
    Member Abitnutz's Avatar
    Join Date
    Sep 2019
    Last On
    Yesterday @ 06:12 PM
    Location
    Waynesville, Ohio USA
    Posts
    12
    Local Date
    10-24-2020
    Local Time
    11:18 AM
    Thread Starter
    The contoured barrel from Krieger was $450.00. That's for the oversize shank but it's un-threaded, un-chambered...nothing more than contoured and rifled. The original barrel was 30.5 inches long. The Krieger was delivered at least a full 4 inches longer. Having said that. It is a gorgeous barrel. I looked at it with a borescope and it as close to perfect as I've ever seen.

    It's not that I demand this kind of perfection. I would have gladly gone with a less expensive barrel but Krieger is the only barrel maker that makes a barrel large enough to fit a Ross action. Everyone else's barrel shank is too small, at least everyone I could find and I looked pretty hard.

    Now...add your kindly gunsmith costs...and you can see where this is not an inexpensive project.

  10. Thank You to Abitnutz For This Useful Post:


  11. #8
    Senior Member vykkagur's Avatar
    Join Date
    Nov 2019
    Last On
    @
    Location
    Canada
    Posts
    114
    Local Date
    10-24-2020
    Local Time
    12:18 PM
    Lothar Walther makes blanks more than big enough, but they're almost that price not contoured, and only in stainless.

  12. #9
    Advisory Panel browningautorifle's Avatar
    Join Date
    Jul 2008
    Last On
    Today @ 06:09 AM
    Location
    Victoria BC
    Posts
    24,237
    Local Date
    10-24-2020
    Local Time
    08:18 AM
    Quote Originally Posted by Abitnutz View Post
    you can see where this is not an inexpensive project
    Finding a Ross with a full length barrel and nice bore is getting harder every day. If one has a set of wood and what amounts to a parts kit that he wants to shoot then this is about the only way. You can also give it a tight chamber. Add the bore difference for accurate easy to find bullets and it makes it a good alternative...yes, you pay what we used to pay for just the rifle to get a barrel made but we're at that point now. Some guys pay $2500 to build an AR these days and look where that's going... Looking forward to a guided tour of the end result.
    Regards, Jim

  13. Thank You to browningautorifle For This Useful Post:


  14. #10
    Senior Member vykkagur's Avatar
    Join Date
    Nov 2019
    Last On
    @
    Location
    Canada
    Posts
    114
    Local Date
    10-24-2020
    Local Time
    12:18 PM
    Quote Originally Posted by Abitnutz View Post
    The contoured barrel from Krieger was $450.00. That's for the oversize shank but it's un-threaded, un-chambered...nothing more than contoured and rifled. The original barrel was 30.5 inches long. The Krieger was delivered at least a full 4 inches longer. Having said that. It is a gorgeous barrel. I looked at it with a borescope and it as close to perfect as I've ever seen.

    It's not that I demand this kind of perfection. I would have gladly gone with a less expensive barrel but Krieger is the only barrel maker that makes a barrel large enough to fit a Ross action. Everyone else's barrel shank is too small, at least everyone I could find and I looked pretty hard.

    Now...add your kindly gunsmith costs...and you can see where this is not an inexpensive project.
    For $35 more, they'll give you the same barrel with a .287 bore, for those who want to re-barrel an M-10 Stalker. Not cheap, but then neither is a good M-10.

+ Reply to Thread
Page 1 of 2 1 2 LastLast

Similar Threads

  1. I'm going to re-barrel my Ross Mk III
    By Abitnutz in forum The Ross Rifle Knowledge Library Collectors Forum
    Replies: 20
    Last Post: 10-30-2019, 05:56 PM
  2. Ross 280 barrel
    By eliwhitley in forum The Ross Rifle Knowledge Library Collectors Forum
    Replies: 6
    Last Post: 02-03-2018, 05:33 PM
  3. Ross MkII*** Barrel Locking screw
    By Simon P in forum The Ross Rifle Knowledge Library Collectors Forum
    Replies: 3
    Last Post: 04-19-2015, 03:12 AM
  4. Ross 1905 barrel set-back
    By ForgottenWeapons in forum The Ross Rifle Knowledge Library Collectors Forum
    Replies: 6
    Last Post: 09-20-2014, 10:09 PM
  5. Ross Barrel Removal
    By cr17 in forum Gunsmithing for Old Milsurps
    Replies: 2
    Last Post: 02-24-2010, 06:31 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts