+ Reply to Thread
Page 3 of 3 FirstFirst 1 2 3
Results 21 to 23 of 23

Thread: FN Browning 1910/22 jamming on first round not ejecting properly

Click here to increase the font size Click here to reduce the font size
  1. #21
    Member bnz41's Avatar
    Join Date
    Jun 2012
    Last On
    Today @ 12:16 PM
    Location
    Essex England
    Posts
    32
    Local Date
    02-22-2020
    Local Time
    06:23 PM
    Thread Starter

    1910/22 It works.

    On the advice of two forum members who suggested there maybe a fault with the striker (firing pin). I was made aware that the 1910/22 & the 1910 share the same striker assembly so swap them to see if the 1922 ejects. I did this and yes it works.

    This is a picture of them side by side you can see the 1922 one is the shorter of the two no way was that going to work. It's a pity the gunsmith that worked on it never noticed.
    Thank you for the advice guys.

    [ATTACH=CONFIG]105379[/ATTACHs
    Attached Thumbnails Click image for larger version

Name:	20200209_092931.jpg‎
Views:	30
Size:	1.76 MB
ID:	105379  
    Last edited by bnz41; 02-09-2020 at 01:37 PM. Reason: spelling mistake

  2. The Following 3 Members Say Thank You to bnz41 For This Useful Post:


  3. # ADS
    Friends and Sponsors
    Join Date
    October 2006
    Location
    Milsurps.Com
    Posts
    All Threads
     

  4. #22
    Advisory Panel browningautorifle's Avatar
    Join Date
    Jul 2008
    Last On
    Today @ 01:18 PM
    Location
    Victoria BC
    Posts
    22,947
    Local Date
    02-22-2020
    Local Time
    10:23 AM
    Soon this shall pass, very soon... Sounds like the gunsmith wasn't very interested.
    Regards, Jim

  5. Avoid Ads - Become a Contributing Member - Click HERE
  6. #23
    Advisory Panel Lee Enfield's Avatar
    Join Date
    Oct 2006
    Last On
    Today @ 02:11 AM
    Location
    out there
    Posts
    1,454
    Local Date
    02-22-2020
    Local Time
    11:23 AM
    Quote Originally Posted by browningautorifleicon View Post
    Soon this shall pass, very soon... Sounds like the gunsmith wasn't very interested.
    It's probably more a case of lacking experience in the specific firearm.

    I'm sure one of my friends suggested the source of the problem to me, and I didn't believe him based on the fact the the firing pin set off cartridges, and ejected properly when "dry firing".

    FYI the MAB Model "D" also uses a 1910/1922 compatible firing pin.

    BSN from the Republic of Alberta

    http://www.cartridgecollectors.org/

+ Reply to Thread
Page 3 of 3 FirstFirst 1 2 3

Similar Threads

  1. Last Round jamming, feed lip adjustment
    By rickv100 in forum The Lee Enfield Knowledge Library Collectors Forum
    Replies: 43
    Last Post: 04-02-2018, 12:28 PM
  2. M1 Garand ejecting clip early
    By Mikesm44 in forum M1 Garand/M14/M1A Rifles
    Replies: 12
    Last Post: 04-25-2014, 01:28 PM
  3. M1 not ejecting
    By TDH in forum M1 Garand/M14/M1A Rifles
    Replies: 9
    Last Post: 07-12-2009, 03:01 PM
  4. FN/Browning 1910/22 pistols
    By Light Infantry in forum Milsurps General Discussion Forum
    Replies: 5
    Last Post: 11-10-2008, 08:17 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts